Sr+ Setup For Pioneer Plasma Displays; Multi Room Setup - Pioneer PDK-1014 Operating Instructions Manual

Other Settings
• ATT 10dB – 10dB of limiting
• LFE OFF – No sound from LFE channel
3 When you're finished, press RETURN.
You will return to the Other Setup menu.

SR+ Setup for Pioneer plasma displays

Make the following settings if you have connected a
Pioneer plasma display to this receiver using an SR+
cable. Note that the number of function settings available
will depend on the plasma display you've connected.
See also Using this receiver with a Pioneer plasma display
on page 65 and Using the SR+ mode with a Pioneer
plasma display on page 66.
1 Select 'SR+ Setup' from the Other Setup menu.
6. Other Setup
[ a . DRC Setup
[ b . Dual Mono Setup
[ c . LFE ATT Setup
[ d . SR+ Setup
[ e . Multi Room Setup
[ f . 12V Trigger Setup
[ g . SACD GAIN Setup
2 Select the 'PDP Volume Control' setting you
want.
6d. SR+ Setup
PDP Volume Control
PDP Input Select
DVD/LD
TV/SAT
DVR
VIDEO1
VIDEO2
Monitor Out Connect
• OFF – The receiver does not control the volume of the
plasma display
• ON – When the receiver is switched to one of the
inputs that use the plasma display (DVD/LD, or
another one of functions below), the volume on the
plasma display is muted so only sound from the
receiver is heard.
3 Assign any input source connected to the plasma
display to the corresponding input number.
This matches the receiver's input source with a
numbered video input on the plasma display. For
example, assign DVD/LD to input-2 if you have
connected the your DVD video output to video input 2 on
the plasma display.
]
]
]
]
]
]
]
[ OFF ]
[ input-3 ]
[ TV ]
[ input-1 ]
[ OFF ]
[ OFF ]
[ input-2 ]
• The Monitor Out Connect should be set to the input
that you've used to connect this receiver to your
plasma display.
6d. SR+ Setup
PDP Volume Control
[ ON ]
PDP Input Select
DVD/LD [ input-3 ]
TV/SAT [ TV ]
DVR [ input-1 ]
VIDEO1 [ OFF ]
VIDEO2 [ OFF ]
Monitor Out Connect
[ input-2 ]
4 When you're finished, press RETURN.
You will return to the Other Setup menu.

Multi Room Setup

VSX-2014i model only
• Default setting: VARIABLE / Setting 1
If you've made multi-room connections (see Multi-room
listening on page 61) you may need to specify your
volume setting and IR receiver type.
1 Select 'Multi Room Setup' from the Other Setup
menu.
6. Other Setup
[ a . DRC Setup
[ b . Dual Mono Setup
[ c . LFE ATT Setup
[ d . SR+ Setup
[ e . Multi Room Setup
[ f . 12V Trigger Setup
[ g . SACD GAIN Setup
2 Select the volume level setting.
6e. Multi Room Setup
Volume Level
[ VARIABLE ]
IR Setting
[Setting 1]
CAUTION:If the "FIXED"
position is chosen, the
volume will be loud.
• VARIABLE – Use this setting if you've connected a
power amplifier in the sub room (this receiver is
simply being used as a pre-amp) and you will be
using this receiver's controls to adjust the volume.
• FIXED – Use this setting if you've connected a fully
integrated amplifier (such as another Pioneer VSX
receiver) in the sub room and want to use that
receiver's volume controls.
Caution
• With the FIXED setting, the source is sent from this
receiver at maximum volume, so make sure the
volume is quite low in the sub room at first and then
experiment to find the correct level.
6d. SR+ Setup
PDP Volume Control
[ ON ]
PDP Input Select
DVD/LD [ input-2 ]
TV/SAT [ TV ]
DVR [ input-1 ]
VIDEO1 [ OFF ]
VIDEO2 [ OFF ]
Monitor Out Connect
[ input-2 ]
]
]
]
]
]
]
]
6f. Multi Room Setup
Volume Level
[ FIXED ]
IR Setting
[Setting 1]
CAUTION:If the "FIXED"
position is chosen, the
volume will be loud.
11
71
En