Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for AXIOMTEK AC5410P
Summary of Contents for AXIOMTEK AC5410P
- Page 1 AX5410P 16 Channels Opto-Isolated Digital Input Card with PCI Bus User’s Manual...
- Page 2 AXIOMTEK assumes no responsibility for any inaccuracies that may be contained in this document. AXIOMTEK makes no commitment to update or to keep current the information contained in this manual.
- Page 3 Wear a wrist-grounding strap, available from most electronic component stores, when handling boards and components. Trademarks Acknowledgments AXIOMTEK is a trademark of AXIOMTEK Co., Ltd. IBM is a registered trademark of International Business Machines Corporation. MS-DOS, Microsoft C and QuickBasic are trademarks of Microsoft Corporation.
- Page 4 Unpacking The AX5410P is packed in an anti-static bag. The board has components that are easily damaged by static electricity. Do not remove the anti-static wrapping until proper precautions have been taken. Safety instructions in front of this User’s Manual describe anti-static precautions and procedures.
-
Page 5: Table Of Contents
T a b l e C o n t e n t s Chapter 1 Introduction General Description.......... 1 Features ............1 Specifications........... 2 Screw Terminal Panel ........2 Software Package ..........3 Chapter 2 Installation Base I/O Port Address and IRQ Level ....5 Connector Pin Assignments ...... - Page 6 This page does not contain any information.
-
Page 7: Chapter 1 Introduction
AX5410P 16 Channel Opto-Isolated Digital Input Card User’s Manual C h a p t e r Introduction General Description The AX5410P provides 16 isolated digital input channels. It plugs directly into any 32-bit PCI Bus. The 16 opto-isolated D/I channels are ideal for sensing digital inputs, and provide 1000V of isolation. -
Page 8: Specifications
AX5410P 16 Channel Opto-Isolated Digital Input Card User’s Manual Specifications Isolated Input Indication Display: 16 Red LEDs Indication Mode: Logic “1” :LED on Logic “0” :LED off Opto-isolator: PC814 Input Channels: 16 Isolation: 1000V channel-to-channel and channel-to-ground Throughput: 10KHz max. Interrupt Throughput: 7KHz max. -
Page 9: Software Package
AX5410P 16 Channel Opto-Isolated Digital Input Card User’s Manual Software Package AS59020: DAC Win 95 Driver AS59040: DAC Win NT Driver Introduction... - Page 10 AX5410P 16 Channel Opto-Isolated Digital Input Card User’s Manual This page does not contain any information. Introduction...
-
Page 11: Installation
AX5410P 16 Channel Opto-Isolated Digital Input Card User’s Manual C h a p t e r Installation Base I/O Port Address and IRQ Level AX5410P occupies eight I/O port spaces. The PCI Plug & Play BIOS assigns the I/O port base address and IRQ level. From the device driver, user can get the base address, IRQ level and plus the slot number where AX5410P is plugged into. -
Page 12: Ac Or Dc Input Select
AX5410P 16 Channel Opto-Isolated Digital Input Card User’s Manual Jumper +12V 18,19,37 AC or DC Input Select Both AC and DC signals can be input to AX5410P channels. Each input channel is equipped with jumper-selectable filter. The jumpers are JP17 and JP18. For DC input, filter is not required. -
Page 13: Jumper Settings
AX5410P 16 Channel Opto-Isolated Digital Input Card User’s Manual Jumper Settings AX5410P accepts two kinds of signals as digital inputs: voltage input and dry contact, both configurable by setting the jumpers JP1 through JP16 onboard. Refer to the following diagrams for the corresponding jumper settings of both signals. -
Page 14: Signal Wiring
AX5410P 16 Channel Opto-Isolated Digital Input Card User’s Manual Signal Wiring The AX5410P accepts digital input signals from TTL devices, dry contacts and voltage inputs. Install jumpers (JP1~JP16) for dry contacts or voltage inputs according to previous section. With jumpers installed, the input signal is isolated from the internal circuit. -
Page 15: 2.5.3 Voltage Input
AX5410P 16 Channel Opto-Isolated Digital Input Card User’s Manual JP16 DI 1+ DI 1- DI 2+ DI 2- DI 16+ DI 16- VOLTAGE REMOTE SOURCE SWITCH 2.5.3 Voltage Input Set jumpers and place a voltage source (3V-24V) according to the description below. The voltage input signals are isolated from the internal circuit. -
Page 16: Ttl Devices (With Isolation)
AX5410P 16 Channel Opto-Isolated Digital Input Card User’s Manual 2.5.4 TTL Devices (With Isolation) Simply connect the output points of TTL devices to AX5410P. The figures below give a brief description of the connections and jumpers settings. DATA STATUS JP16 DI 1+ DI 1- DI 2+... -
Page 17: Hardware Installation
AX5410P 16 Channel Opto-Isolated Digital Input Card User’s Manual Hardware Installation The AX5410P board is shipped with protective electrostatic cover. When unpacking, touch the board’s electrostatically shielded packaging with the metal frame of your computer to discharge the accumulated static electricity prior to touching the board. - Page 18 AX5410P 16 Channel Opto-Isolated Digital Input Card User’s Manual This page does not contain any information.
-
Page 19: Register Structure & Format
AX5410P 16 Channel Opto-Isolated Digital Input Card User’s Manual C h a p t e r Register Structure & Format I/O Address Mapping This chapter describes the register format and function. The AX5410P use only one I/O address. The register is 16 bits wide and show below. - Page 20 AX5410P 16 Channel Opto-Isolated Digital Input Card User’s Manual This page does not contain any information.
-
Page 21: Device Driver
AX5410P 16 Channel Opto-Isolated Digital Input Card User’s Manual C h a p t e r Device Driver The AX5410P device driver is suitable for Plug & Play under DOS environment when generating information from PCI BIOS. This chapter describes in detail on how to install the device driver and use the device driver command to get base address, IRQ level, slot number. -
Page 22: Using The Device Driver Command
* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * Copyright 1998 by AXIOMTEK Co., LTD Ver 1.0... -
Page 23: Programming Examples
AX5410P 16 Channel Opto-Isolated Digital Input Card User’s Manual NOTE: The question mark “?” must be replaced by a card number. If Base Address returns to 0, it means all information retrieved by the card number are not available. Programming Examples 4.2.1. -
Page 24: Sample Program In Turbo Pascal
AX5410P 16 Channel Opto-Isolated Digital Input Card User’s Manual close(fd); clrscr(); printf("BASE ADDRESS :%x\n",base); printf("SLOT NUMBER :%x\n", busno); if (base = = 0) { printf("ERROR INFORMATION !\n"); exit(0); 4.2.2. Sample Program in Turbo Pascal * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * Example program for Turbo PASCAL language To get BASE ADDRESS SLOT NUMBER via device driver... -
Page 25: Sample Program In Qbasic 4.5
AX5410P 16 Channel Opto-Isolated Digital Input Card User’s Manual close(fdw); close(fdr ); writeln('BASE ADDRESS : ',addr:10); writeln('SLOT NUMBER :',slotno:10); if addr <> 0 then writeln('The information are correct'); END. 4.2.3. Sample Program in QBasic 4.5 * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * Example program for QB45 language To get BASE ADDRESS SLOT NUMBER via device driver... - Page 26 AX5410P 16 Channel Opto-Isolated Digital Input Card User’s Manual This page does not contain any information.
-
Page 27: Appendix A Block Diagram
AX5410P 16 Channel Opto-Isolated Digital Input Card User’s Manual A p p e n d i x Block Diagram CHANNEL1 VISO DI 1+ OPTO ISOLATOR DI 1- VISO CHANNEL16 DI 16+ OPTO ISOLATOR JP16 DI 16- Block Diagram... - Page 28 AX5410P 16 Channel Opto-Isolated Digital Input Card User’s Manual This page does not contain any information.
-
Page 29: Appendix B Location Diagram
AX5410P 16 Channel Opto-Isolated Digital Input Card User’s Manual A p p e n d i x Location Diagram Location Diagram... - Page 30 AX5410P 16 Channel Opto-Isolated Digital Input Card User’s Manual This page does not contain any information.
Need help?
Do you have a question about the AC5410P and is the answer not in the manual?
Questions and answers