Related Manuals for Hollyland HLHC050E
Summary of Contents for Hollyland HLHC050E
- Page 1 50M single Cat5e/6 HDMI wall plate extender with bi-direction IR (HLHC050E) User manual...
-
Page 2: Table Of Contents
Preface ....................1 1. Cautions ....................2 2. About ....................3 3. Installation ..................6 4. Operation instruction ................9 5. Maintenance ..................11 6. Truble shooting .................. 11... -
Page 3: Preface
Preface Thanks for purchasing our HDMI Single Cat5e/6 Wall Plate Extender. Before using this product, read this user manual carefully please. Follow the instruction to keep your safety and avoid products damage. This user manual might be modified irregularly because of updated products. -
Page 4: Cautions
1. Cautions Logo and meaning Careful, warning, dangerous, Pay attend to following items. Cautions Do not use this product in the extreme hot, cold, dusty or humid environments. Prevent friction with hard objects. Avoid the product falling down from a high place, or it may damage the hardware. -
Page 5: About
2. About Product model and standard: Single Cat5e/6 Wall Plate Extender includes transmitter and receiver. Transmitters combine HDMI video, audio and control signals, then transmit them through single CAT5e cable. Receivers get these signals, separate signals and rebuild video, audio and control ones, output through HDMI interfaces. - Page 6 Supports power over UTP cable, single 12V DC power supply from any side of TX or RX. 38KHz bi-direction remote IR (RX->TX and TX->RX). Both HDMI input and output are compatible with HDCP 1.2. Be compatible with DVI 1.0. ...
- Page 7 Product introduction Transmitter： 1. HDMI Input port, connect to Video source 2. DC 12V input 3. IR blaster output 4. IR receiver input 5. Status indicator 6. Power indicator 7. Internal DC input port 8. CAT5e/6 cable RJ45 port Receiver：...
-
Page 8: Installation
1. HDMI Output port, connect to display terminal 2. DC 12V input 3. IR blaster output 4. IR receiver input 5. Status indicator 6. Power indicator 7. Internal DC input port 8. CAT5e/6 cable RJ45 port Packing list 1 unit transmitter, 1 unit receiver. ... - Page 9 b) Basing on real request, make CAT5e/6 cables for connecting the transmitter and the receiver. The length can NOT be more than distance of parameters. c) CAT5e/6 cables should be far away from electromagnetic disturbance sources. Such as AC motors, electro soldering, fluorescents, microwave ovens, etc.
- Page 10 b) Insert IR blaster cable to extender TX IR OUT port. IR blaster should be close to your player or other controlled equipment. TX IR IN port can be connected an IR receiving cable. c) Insert CAT5e/6 cable to CAT5e/6 port. a) Connect power adapter or provide DC input from rear DC input port.
-
Page 11: Operation Instruction
4. Operation instruction Getting started After finishing all steps above, system is workable, follow below steps. a) Ensure the video source and the display terminal are powered on. b) Ensure all input, output cables are connected. c) Insert TX or RX power adapters into power plug bases. d) Green power indicator will light. - Page 12 receiver. IR signal will be transmitter to extender RX side IR output port, to control display terminal directly. EDID call back function Products support EDID call back function. Receiver unit will read EDID from display terminal, and then pass this EDID information to transmitter unit. The transmitter unit will update internal NVRAM to save new EDID information, and inform video source to read updated EDID information.
-
Page 13: Maintenance
5. Maintenance Storage conditions Products storage temperature should be -20°C~60°C. For long time storage requirement, please use original carbon boxes, and avoid from high humid, acid base or dusty place. Maintenance Warning To ensure your safety, place choose original adapters. And provide stable AC input according to this manual. - Page 14 Check transmitter and receiver power first. And then check if transmitter unit video indicator is light. If it is not, check video source please. If it is, check receiver unit video indicator. If receiver video indicator is not light, check CAT5e/6 cable please. If length of cable is longer than maximum distance, the system is not workable.