Mitsubishi FX2NC-485ADP Installation Manual

This manual contains text, diagrams and explanations which will guide the reader in the correct
installation, safe use and operation of the FX
be read and understood before attempting to install or use the unit. Further information can be found in
the associated manuals mentioned below.
Specifications are subject to change without notice
Safety guidelines for the user and protection of the FX
This manual has been written to be used by trained and competent personnel. The definition of such a
person or persons is as follows:
a) Any engineer using the product associated with this manual, should be of a competent nature,
trained and qualified to the local and national standards. These engineers should be fully aware of
all aspects of safety with regards to automated equipment.
b) Any commissioning or service engineer must be of a competent nature, trained and qualified to
the local and national standards.
c) All operators of the completed equipment should be trained to use that product in a safe and
coordinated manner in compliance to established safety practices.
Note: The term 'completed equipment' refers to a third party constructed device which contains or uses
the product associated with this manual.
Notes on the Symbols Used in this Manual
At various times through out this manual certain symbols will be used to highlight points of information
which are intended to ensure the users personal safety and protect the integrity of equipment.
1) Indicates that the identified danger WILL cause physical and property damage.
2) Indicates that the identified danger could POSSIBLY cause physical and property
damage.
• Under no circumstances will Mitsubishi Electric be liable or responsible for any consequential damage
that may arise as a result of the installation or use of this equipment.
• All examples and diagrams shown in this manual are intended only as an aid to understanding the
text, not to guarantee operation. Mitsubishi Electric will accept no responsibility for the actual use of
the product based on these illustrative examples.
• Please contact a Mitsubishi distributor for more information concerning applications in life critical
situations or high reliability.
Associated Manuals
PROGRAMMING MANUAL, PROGRAMMING MANUAL ΙΙ, or FX COMMUNICATION USER'S MANUAL
mentioned below are not provided in sets with a product.
Contact our agent where the product was purchased to request the manuals accordingly.
Manual Name
This FX -485ADP INSTALLATION
2NC
manual MANUAL
FX COMMUNICATION USER'S
#
MANUAL
✩
FX HARDWARE MANUAL
1S
✩
FX /FX HARDWARE MANUAL
0 0N
✩
FX HARDWARE MANUAL
1N
✩
FX HARDWARE MANUAL
2N
FX HARDWARE MANUAL(DSS/DS)
2NC
✩
✩
PROGRAMMING MANUAL
✩
PROGRAMMING MANUAL ΙΙ
FX -CNV-BD
✩ 1N
Special Adapter Connection Board
FX -CNV-BD
✩ 2N
Special Adapter Connection Board
# Indispensable manual
This manual describes the installation the and specifications of the 485ADP .
For details on wiring (including use of terminal resistor and preparation of cable) with communication equipment,
system configuration and communication setting, and program examples, refer to the "FX COMMUNICATION USER'S
MANUAL".
-485ADP (hereafter abbreviated to "485ADP") and should
2NC
Manual
Number
JY997D01201
JY992D69901
JY992D83901
JY992D47501
JY992D89301
JY992D66301
JY992D76401
(D/UL) JY992D87201
JY992D76401
JY992D88101
JY992D84701
JY992D63601
✩ Either manual is necessary.
FX -485ADP
2NC
Installation Manual
JY997D01201B
2NC
Description
Describes contents related to installation of the
FX -485ADP Module.
2NC
Describes contents related to communication
available in FX Series PLC such as wiring,
communication setting, and program examples.
Describes contents related to hardware of FX
Series PLC such as specifications, wiring, and
installation.
Describes contents related to instruction in FX
FX /FX /FX/FX /FX
0S 0N 2 2C
Describes contents related to instruction in FX
FX /FX /FX Series PLC.
1N 2N 2NC
Describes contents related to installation of the
each board.
-485ADP.
/
0
Series PLC.
1S
/