Download Print this page

Advertisement

Quick Links

DESCRIPTION
The W894A Proportional Level Controller provides auto-
matic slope control of paving, curbing, grading and similar
mobile equipment. The Controller measures deviation from
a gravity reference and supplies a two-wire output for driving
a servovalve such as the MCV113. The W894A operates in
12 Volt electrical systems.
Two modules are housed in the case of the Controller with
plug-in electrical interconnections. The transducer sensing
module electromagnetically measures the deviation of the
equipment it is mounted on from a gravity reference. The
amplifier module accepts the signals from the slope sensing
module and uses the deviation to provide a corrective output
to keep the equipment at the prescribed slope.
FEATURES
Rugged aluminum housing
Adjustable sensitivity
RUN/STANDBY switch permits operator to switch to
manual control
Deviation meter with zero center shows deviation from
setpoint in RUN or STANDBY positions
ORDERING INFORMATION
SPECIFY
1. Model Number W894A. See Table A.
2. Accessories
TABLE A.
ORDER NUMBER
W894A1053
© Danfoss, 2013-09
DESCRIPTION
12Vdc, Drives MCV113
Hot Side Switching
BLN-95-8974-5
W894A
Proportional Level Controller
BLN-95-8974-5
Reverse polarity and short circuit protection
Moisture and corrosion resistant
Accepts a remote slope setpoint adjuster
Withstands vibration and shock
ACCESSORIES
Order the necessary parts from the list below:
1. MCV113 Servovalve
2. Q625A Remote Setpoint (hand-held setpoint with inte-
gral coiled cord and MS connector).
3. Q625A Remote Setpoint (panel-mount setpoint with ter-
minal strip).
4. KW01001 Cable (two-foot coiled cable that extends to
ten feet. Has straight connector on one end and spade
lugs on the other. Mates with the five-pin W894A connec-
tor and the panel-mount Q625A Remote Setpoint)
5. KW01013 Cable (two-foot coiled cable that extends to
ten feet. Has right angle connector on one end and
straight connector on the other. Mates with the ten-pin
W894A connector and an MS3102A18-1P plug).
6. KW01012 Cable (four-foot coiled cable that extends to
twenty feet. Has right angle connector on one end and
straight connector on the other. Mates with the ten-pin
W894A connector and an MS3102A18-1P plug).
Issued: March 1992
1

Advertisement

loading

Summary of Contents for Danfoss W894A

  • Page 1 The Controller measures deviation from a gravity reference and supplies a two-wire output for driving a servovalve such as the MCV113. The W894A operates in 12 Volt electrical systems. Two modules are housed in the case of the Controller with plug-in electrical interconnections.
  • Page 2 With gain potentiometer set to maximum, gain will be 1.7 null meter reading at the red/white division indicates a 3 to 2.7 Vdc per 0.3% slope error input. Vdc output. BLOCK DIAGRAM 1183 Schematic of Transducer and Amplifier Sections of the W894A. CONNECTION DIAGRAM 206C Typical System Connections. BLN-95-8974-5...
  • Page 3 HUMIDITY After being placed in a controlled atmosphere of 95% SHOCK humidity at 49° C (120° F) for 10 days, the W894A will 50 g's for 11 milliseconds. Three shocks in both direc- perform within specification limits. tions of the 3 mutually perpendicular axes for a total of 18 shocks.
  • Page 4 EUROPE Phone: (763) 509-2084 Fax: (763) 559-0108 ORDER FROM DEVICE REPAIR Danfoss (Neumünster) GmbH & Co. Order Entry Department For devices in need of repair or evaluation, include a Krokamp 35 description of the problem and what work you believe...