Pioneer CDJ-1000 Operating Instructions Manual
Compact disc player
Hide thumbs
Also See for CDJ-1000:
- Operating instructions manual (96 pages) ,
- Service manual (93 pages) ,
- Training manual (30 pages)
Table of Contents
Advertisement
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Pioneer CDJ-1000
Summary of Contents for Pioneer CDJ-1000
- Page 1 COMPACT DISC PLAYER CDJ-1000 Operating Instructions...
- Page 2 NOTE: THE NO USER-SERVICEABLE PARTS COMPARTMENT WARNING IS LOCATED ON THE APPLIANCE BOTTOM. <DRB1297>...
-
Page 3: Important Notice
[For U.S. model] IMPORTANT NOTICE H006AEn The serial number for this equipment is located in the rear panel. Please write this serial number on your enclosed warranty card and keep it in a secure area. This is for your security. <DRB1297>... -
Page 4: Table Of Contents
CD lens cleaner The player’s pickup lens should not become dirty in normal use. If for some rea- son, the lens becomes soiled and malfunctions, contact your nearest PIONEER authorized service center. Lens cleaners for CD players are commercially available, but special care should be exercised in their use as some may cause damage to the lens. -
Page 5: Storing Discs
When performing forced ejection, be sure to follow the precautions below. 1 Be sure to turn OFF the power of the CD player, and check that the disc has stopped rotating. It takes about 60 seconds for the disc to stop rotating after the power has been turned OFF. -
Page 6: Features
BEFORE OPERATIONS FEATURES The CDJ-1000 compact disc player is designed for use by DJs providing all the func- tions and performance required in disco clubs while offering performance, sound quality and functionality superior to any analog player. JOG DIAL The large 206 mm diameter Jog dial enables better handling than an analog turntable. -
Page 7: Connections
Connect the supplied control cord to enable control of the unit from the mixer to allow fader start play and back cue. Connecting DJM-600 CDJ-1000 ÷ CD1 and CD2 on a DJM-300 or DJM-500 mixer are connected to player A and player B respectively, in the same way as shown above. -
Page 8: Connecting To Other Devices
When all connections have been made, connect the power cord to the AC inlet on the rear panel of the player and connect the power plug to an AC wall outlet or to a power receptacle on the rear panel of the amplifier. <DRB1297> Supplied audio cable Digital signal cable CDJ-1000 CDJ-1000... -
Page 9: Panel Facilities
PANEL FACILITIES Top Panel 1 DISPLAY CD TEXT/WAVE (ZOOM) button (*) Each press of this button toggles the display between WAVE display and CD-TEXT disc/track title display. When the button is held down for 1 second or longer, the WAVE display cycles between the 1 track full-scale and 2x zoom scale. 2 TIME MODE/AUTO CUE button (*) TIME MODE: Each time this button is pressed, the time display changes between elapsed play-... -
Page 10: Display
BEFORE OPERATIONS: PANEL FACILITIES 29 Memory Card Loading Slot P.16 30 Memory Card indicator P.16 Lights when the MMC card is being accessed. ¶ Do not remove the card or turn off the power when this lamp is on. 31 Play/Pause indicator (6) Lights during play and flashes during pause. -
Page 11: Disc Loading/Unloading
DISC LOADING/UNLOADING Label surface up Insert straight 1. Set the rear-panel POWER switch to ON. Do not force a disc into the unit when the POWER switch is set to OFF as this may damage the disc and the unit. 2. -
Page 12: Stopping Playback
CUE button (back cue) before pressing the EJECT button (0) to eject the disc. ¶ Playback will stop and the disc will be ejected. ¶ Note that the CDJ-1000 does not come with a stop button. To Pause Play During playback, press the PLAY/PAUSE button (6). -
Page 13: Changing Playback Speed
[Amending the Cue point] 1. During playback, press the CUE button. ¶ This will take you back to the set track position. 2. In the VINYL mode, to set the Cue point, go through steps 2 and 3 as mentioned above. 7 Real-time cue During playback, press the LOOP IN/REALTIME CUE button at the desired Cue point. -
Page 14: Advanced Operations
ADVANCED OPERATIONS 7 Fader start play Using the cross fader start function of the DJM-600, DJM-500 or DJM-300, step 10 above can be eliminated for even simpler mixing. In addition, when the ADVANCED OPERATIONS LOOP IN/REALTIME LOOP OUT CUE (IN ADJUST) (OUT ADJUST) HOT CUE A HOT CUE B... -
Page 15: Reversing Playback
(See page. 7 for instructions on how to connect the player.) Relay Play Using Two Players (*) If you connect the terminals of this player with another CDJ series CD player using the attached control cord then you will be able to relay play. P. 7. -
Page 16: Using Cue Points/Loop Points Memory
ADVANCED OPERATIONS USING CUE POINTS/LOOP POINTS MEMORY This unit can store Cue points and Loop points for each disc in internal or on a Multimedia Card (MMC). Using Internal Memory When a commercially available Multimedia Card (MMC) is not inserted in the card slot, the internal memory is used. -
Page 17: Copying Mmc Data
7 Storing CUE points Insert a Multimedia Card in the card insertion slot and perform the same pro- cedure as when the internal memory is used. P.16 7 Storing Loop points Insert a Multimedia Card in the card insertion slot and perform the same pro- cedure as when the internal memory is used. -
Page 18: Troubleshooting
8cm disc and adaptor are used. This is NOT a malfunction. ¶ The BPM value measured by the CDJ-1000 may differ from the BPM value recorded on a CD or from our DJ mixer, but this difference is a result of differences in the BPM value measurement method;... -
Page 19: Error Message Display
Error message display When the CDJ-1000 CD player is unable to operate properly, an error code is dis- played on the display panel. Check the error code displayed against the following table and take the recommended action to correct the error. If an error code other... -
Page 20: Specifications
After all, we want you listening for a lifetime. PIONEER CORPORATION 4-1, Meguro 1-Chome, Meguro-ku, Tokyo 153-8654, Japan PIONEER NEW MEDIA TECHNOLOGIES, INC. Multimedia and Mass Storage Division: PIONEER ELECTRONICS OF CANADA, INC. Industrial Products Department: 300 Allstate Parkway, Markham, Ontario L3R OP2, Canada <DRB1297>...
Need help?
Do you have a question about the CDJ-1000 and is the answer not in the manual?
Questions and answers