The use of a substitute replacement component which does Leakage 0.5mA current Device not have the same safety characteristics as the PIONEER tester under recommended replacement one, shown in the parts list in test this Service Manual, may create shock, fire, or other hazards.
Page 3
CLASS 1. A specially instructed person should servicing operation of the apparatus. LABEL CHECK CDJ-1000MK2/ TLXJ Type Only CDJ-1000MK2/ WYXJ Type Only Additional Laser Caution 1. Laser Interlock Mechanism...
Page 4
By following the instructions in this manual, be sure to apply the prescribed grease or glue to proper portions by the appropriate amount.For replacement parts or tools, the prescribed ones should be used. CDJ-1000MK2...
6. ADJUSTMENT ..............................64 7. GENERAL INFORMATION ..........................65 7.1 DIAGNOSIS..............................65 7.1.1 SERVICE MODE ..........................65 7.1.2 DISASSEMBLY ..........................75 7.1.3 On Discharge of the Capacitor ......................80 7.1.4 CLEANING ............................80 7.1.5 POWER ON SEQUENCE ........................81 7.2 PARTS ..............................84 7.2.1 IC................................84 8. PANEL FACILITIES ............................93 CDJ-1000MK2...
1. SPECIFICATIONS CDJ-1000MK2/ KUCXJ type 1. General 3. Accessories System ..............Compact disc digital audio system Operating instructions ..................1 Power cord ......................1 Power requirements ................AC 120 V, 60 Hz Audio cable ......................1 Power consumption .................... 33 W Control cord ......................
Polyethylene Bag Z21-038 NSP 15 Label VRW1629 (230 x 340 x 0.03) (2) CONTRAST TABLE CDJ-1000MK2/KUCXJ, TLXJ and WYXJ types are constructed the same except for the following: Part No. Mark No. Symbol and Description KUCXJ type TLXJ type WYXJ type >...
2.2 EXTERIOR SECTION (1/2) Refer to "2.3 Exterior (2/2) section". TLXJ Type Only WYXJ Type Only Refer to " 2.4 Slot -IN Mechanism section". NON-CONTACT SIDE CONTACT SIDE CDJ-1000MK2...
Page 9
NSP 28 Rear Panel Cord Clamper ZCB-069Z Heat Sink DNG1082 (2) CONTRAST TABLE CDJ-1000MK2/KUCXJ, TLXJ and WYXJ types are constructed the same except for the following: Part No. Mark No. Symbol and Description KUCXJ type TLXJ type WYXJ type 6 PSWB Assy...
3.4 MAIN (2/4), FLRB and SLMB ASSYS SLMB ASSY (DWS1309) MAIN ASSY (DWX2303) CLAMP CLAMP FLRB ASSY (DWX2308) CAUTION : FOR CONTINUED PROTECTION AGAINST RISK OF FIRE, REPLACE ONLY WITH SAME TYPE NO. ICP-N20, MFD BY ROHM CO., LTD. FOR IC101 AND IC104. CN201 CDJ-1000MK2...
Page 21
RISK OF FIRE, REPLACE ONLY WITH SAME TYPE NO. ICP-N15, MFD BY ROHM SAME TYPE NO. ICP-N25, MFD BY ROHM SAME TYPE NO. ICP-N10, MFD BY ROHM CO., LTD. FOR IC102 AND IC103. CO., LTD. FOR IC105. CO., LTD. FOR IC106. CDJ-1000MK2...
3.5 MAIN (3/4) and MMCB ASSYS MAIN ASSY (DWX2303) 3/4,4/4 CDJ-1000MK2...
Page 23
: The power supply is shown with the marked box. 2/4,4/4 : PB AUDIO SIGNAL ROUTE : DIGITAL DATA SIGNAL ROUTE CN202 MMCB ASSY (DWX2304) CDJ-1000MK2...
S1305 : 1 S1306 : ¡ SLDB ASSY (DWS1325) TEMPO ZERO POINT ADJ. J1101 SWITCHES SLDB ASSY S1401 : TEMPO RESET S1402 : MASTER TEMPO S1403 : TEMPO RANGE : The power supply is shown with the marked box. CDJ-1000MK2...
Page 38
Voltage (V) 0 to 4.9 IC950(LA6562) Pin No. Voltage (V) 11.8 IC711(TC7SET32FU) Pin No. Voltage (V) IC204 (TC7SET08FU) Pin No. Voltage (V) IC205 (TC74VHC08FT) Pin No. Voltage (V) IC850 (BA10358F) Pin No. Voltage (V) IC206(PQ1R33) Pin No. Voltage (V) CDJ-1000MK2...
Page 39
2.6 to 2.8 4.2 to 4.5 IC12 (TC74HCT7007AF) Pin No. Voltage (V) IC607 (PQ025EZ01ZP) 0 to 4.9 Pin No. Voltage (V) IC13 (TC7WU04FU) Pin No. Voltage (V) IC608(TC7WU04FU) Pin No. Voltage (V) 2 to 2.6 2 to 2.6 1.2 to 2.5 CDJ-1000MK2...
Page 40
Voltage (V) Pin No. Voltage (V) Pin No. Voltage (V) Pin No. Voltage (V) 4.2to4.5 IC405 (TC74VHC541FT) Pin No. Voltage (V) 2.6to2.8 1.1to1.5 IC407 (TC7S04FU) Pin No. Voltage (V) IC605 (TC7WT241FU) Pin No. Voltage (V) IC402(TC7WU04FU) Pin No. Voltage (V) CDJ-1000MK2...
Page 41
-29.7 to -30.7 -32.4 to -35.9 -29.7 to -30.7 -30.2 to -32.9 -29.7 to -30.7 -36.4 -29.7 to -30.7 -36.3 -29.7 to -30.7 -36.4 -29.7 to -30.7 -36.4 -29.7 to -30.7 -36.4 -29.7 to -30.7 -36.4 -29.7 to -30.7 CDJ-1000MK2...
B C E C808 Q800 Q800 OFTR Transistor with resistor B C E C831 R810 NARF SIDE B RFAS Chip Part C809 P.C.Board Field effect C814 KN800 transistor C806 C807 C810 R811 R812 C812 119.5 FC DC 3-terminal C855 regulator CDJ-1000MK2...
CN1501 R1509 R1504 CN1501 1.FLAC1 R1505 2.FLAC3 3.FLAC3 R1506 CN1501 R1507 (DNP1987-E) CN303 R1508 (DNP2059-B) MMCB ASSY GNDM CN999 GNDM XMEN S1DO GNDM V3R3 CN202 SMCK SMDI XMDT (DNP2058-B) B C D E F B C D E F CDJ-1000MK2...
Page 47
STCN ASSY SPCN ASSY (DNP2058-B) (DNP2058-B) FLRB ASSY SLMB ASSY CN1501 2.FLAC3 CN1501 3.FLAC3 CN1501 (DNP1987-E) (DNP2059-B) MMCB ASSY GNDM GNDM XMEN S1DO GNDM V3R3 SMCK SMDI XMDT (DNP2058-B) B C D E F B C D E F CDJ-1000MK2...
R1908 W225 IC1901 GNDD IC1901 R1916 R1917 J1801 C1907 R1910 C1906 Q1909 R1913 Q1901 Q1902 Q1902 Q1901 CN1802 OPEN SIDE 1 2 3 OPEN SIDE CN1902 (DNP2059-B) (DNP2059-B) CN1902 CN1801 CN1802 CN12 CN13 G H I G H I CDJ-1000MK2...
4.8 SW POWER SUPPLY and PSWB ASSYS SIDE A SIDE A SW POWER SUPPLY ASSY CN201 CN101 CN101 PRIMARY AC IN COLD 40HI COLD ORANGE WHITE PSWB W318 DWS1312- W319 DWS1311- PSWB ASSY POWER ON OFF (DNP1987-E) CDJ-1000MK2...
DWS1312 and DWS1311 are constructed the same except for the following: Mark Symbol and Description DWS1312 DWS1311 AN1 (AC SOCKET) AKP7032 Not used AN1 (1P AC INLET) Not used BKP1046 PARTS LIST OF CDJ-1000MK2/ KUCXJ Mark No. Description Part No. Mark No. Description Part No. IC950 LA6562 MAIN ASSY IC900...
0% at the slider center after adjustment, turn off the power, and perform fineadjustment again. (Repeat the sequence of fineadjustment, power on, check, power off, and fine-adjustment.) When adjusting the VR1402 (Zero point adj.), adjust it from the hole on the foil side with the SLDB Assy attached to the control panel. CDJ-1000MK2...
@ Mode for checking the error log In this mode, the latest 16 errors can be checked. ¤ Mode for checking the version of the software program In this mode, the version of the software program for each microcomputer can be checked. CDJ-1000MK2...
Page 66
(orange) (red) 7 PLAY/PAUSE (green) CARD 8 IN ADJUST (orange) IN ADJUST 9 OUT ADJUST (orange) OUT ADJUST 0 JOG MODE (green) - TEMPO (blue) VINYL CARD (red) = MASTER TEMPO MASTER TEMPO (green) ~ TEMPO RESET TEMPO RESET CDJ-1000MK2...
Page 67
_ CALL - REV H- 1 + DELETE ¡ MEMORY All of FL, Jog-FL and LED light up. ™ EJECT LOCK (SW) £ EJECT ¢ MEMORY JOG ADJUST H- 2 -TOUCH (VOL) ∞ MEMORY JOG ADJUST -RELESE (VOL) (FL DISPLAY) CENTER CENTER CDJ-1000MK2...
Page 68
V+5V RMIN FLWR 10/50 0.01 10/50 GNDD B2B-PH B6B-PH 10/50 X: Short Connector 10/50 DTC124 (CDJ-1000MK2: OPEN) Y: A side: TEST MODE B side: UP DATE 10/50 MAX1M XM2C-0192-111 MAX232EPE Parts List SEMICONDUCTORS : MAX232EPE : DTA124 : DTC124 CAPACITORS...
Page 69
To enter Test mode, execute the TS command before inserting a disc. Otherwise, audio playback of the first piece of music automatically starts responding to the command from the system-control microcomputer, and any command execution afterwards will not be accepted. In this case, "OFF" is displayed when a command is execution. CDJ-1000MK2...
Page 70
Example: To jump by 100 tracks from the current location toward the outermost track: 100MF (Slider Move Fwd/Rev) To move the slider by about 1 mm toward the outermost/innermost track of the disc. You can move the slider to your desired location by repeatedly executing this command. CDJ-1000MK2...
Page 71
If the AD command is executed after disc insertion, audio playback of the designated piece of music starts. Example: For audio playback of the third piece of music: 3AD Note: Designate the number in the range from 1 to the number of pieces of music recorded. CDJ-1000MK2...
Remove the screw fixing the adjust plate, then screw it into the hole corresponding to the value (-1, -2, -3, +1, or +2) for a load to be added: -1, -2, -3 : To decrease the load +1, +2 : To increase the load Adjust plate To decrease To increase the load the load JOG Check Mode : CANCEL POWER OFF CDJ-1000MK2...
Page 73
No. is not displayed, but you can see the error breakdown code stored in memory. Only in the case of breakdown code 20 (the spindle motor does not rotate), the disc will not be ejected, because this is not a problem of the media. Error Check Mode : CANCEL POWER OFF CDJ-1000MK2...
Page 74
• How to check the software version for the mechanism-control and system-control microcomputers Ver. Check Mode : ON POWER SW RELOOP/EXIT POWER ON Hold it pressed for 10 seconds FL display (13 for the first version) Mechanism-control microcomputer Version display System-control microcomputer Version display Ver. Check Mode : CANCEL POWER OFF CDJ-1000MK2...
× 3 Slot-in Mechanism G5 Assy × 3 × 3 Bottom Plate Disconnect two Connectors. Unhook four springs and Dampers. MAIN Assy Unhook Damper Unhook Damper CN302 CN302 (2p) CN202 CN303 (3p) Unhook Float Spring G5 Unhook Float Spring G5 CDJ-1000MK2...
Page 76
× 2 Unhook × 2 Unhook Caution: MAIN Assy Be careful not to lost Pickup Loading Base Earth Spring. Flexible Cable CN800 STCN Assy • Bottom side CN913 SPCN Assy CN912 • Bottom view × 3 Traverse Mechanism Assy CDJ-1000MK2...
Page 77
Remove the SW Ring. ∗ Caution ( CN1102 ∗ ∗ Be careful not to lose the SW spring. ∗ ∗ ∗ ∗ Remove two screws. Remove the JOG ASSY (JOG A, B and C) SW Ring JOG Assy (JOGA, B, C) CDJ-1000MK2...
Page 78
When inserting a cable in connector, release a lock by all means, and connector locks after inserting it. SW Cushion HH48 ×12 Roller A Assy SW Ring Grease: GYA1001 (ZLB-PN397B) Grease: GYA1001 (ZLB-PN397B) Roller A Assy ×9 Sheet SW JOG Holder 2 JOG Holder 2 CDJ-1000MK2...
Page 79
The cautions on an assembly [ NG ] [ OK ] MFLB Assy MFLB Assy Control Panel Control Panel Slot -In Mecha Slot -In Mecha 25P Flexible Cable 25P Flexible Cable MAIN Assy MAIN Assy Bottom Plate Bottom Plate CDJ-1000MK2...
SW POWER SUPPLY ASSY C105 C105 7.1.4 CLEANING Before shipping out the product, be sure to clean the following positions by using the prescribed cleaning tools: Position to be cleaned Cleaning tools Pickup leneses Cleaning liquid : GEM1004 Cleaning paper : GED-008 CDJ-1000MK2...
Focus Gain adjustment Tracking Gain adjustment Less than 30 minutes TOC read 30 minutes or more Line speed measurement 8 cm Adapter detection Search for 00 min 01 sec 00 min 01 sec Spindle: 3100rpm Audio Data read start CDJ-1000MK2...
Page 83
Measurement approx. 1.3 ms If DONE becomes H, XFRST is set to H in 1 ms. Clearance of the FPGA register and initialization. DONE DATA DONE DATA CDJ-1000MK2...
Page 87
PD3446A8 (MAIN ASSY: IC300) Mecha. Control UCOM • Pin Function (3/3) y l l t i r l a i l a i l a i l a i t i r c i l d i l c t i CDJ-1000MK2...
When the button is held down for 1 second or longer, the POWER switch OFF /ON WAVE display cycles between the 1 track full-scale and 2x zoom scale. This switch is located on the rear panel of the unit. CDJ-1000MK2...
Page 94
It is set to call mode when A, B and C light in green. When the button is back stops and if the dial is rotated, music is output according to the speed the dial pressed, playback starts from the hot cue point. It is off when no hot cue point is turned. has been recorded. CDJ-1000MK2...
Page 95
Even when there may be several memory points in the same block, only one lights. ZOOM indicator Indicates that WAVE is indicated in zoom mode. RELOOP indicator Lights when the unit is in reloop standby or performing a loop. CDJ-1000MK2...
When set in the audio memory display mode the light will flash when record- ing. Jog touch detection indicator In the VINYL mode, this indicator lights when the surface of the Jog dial is pressed. VINYL mode display. Lights up in the VINYL mode. CDJ-1000MK2...