Venting Installation - Superior WRE3042WS Installation And Operation Instructions Manual

OPTIONAL OUTSIDE AIR KIT (MODEL AK4/AK4F)
Installation of outside air kit should be performed during rough fram-
ing of fireplace due to the nature of it's location. Outside combustion
air is accessed through a vented crawl space (AK4F) or through a
sidewall (AK4). See Figure 22, page, 14 for instruction of operating
air kit.
CAUTION: Combustion air inlet ducts shall not
terminate in attic or garage space.
The maximum height for the air vent can not exceed
3 feet below the lue gas outlet of the termination.
Secure to Collars with Metal Tape, Screws
or Straps (Min. of 1/4" x 20" in size)
Air Inlet
Location
Must Allow
For Bushes
or Snow
Vented Crawl Space
(Check Local Codes
Before Installing in a
Vented Crawl Space)
Figure 5- Outside Air Kit
CHIMNEY PIPE
WARNING: Label part number 900599-01 must
be applied by the installer to all chimney pipe
sections but is not required on sections that will
be visible after the installation is complete. Label
must wrap around the circumference of the pipe.
See accessories, page 19 for Kit F2659.
An IHP chimney system consists of 12", 18", 24", 36" and 48" snap-
lock, double-wall pipe segments, planned for maximum adaptability
to individual site requirements. Actual lengths gained after fitting
overlaps must be taken into consideration (lineal gain) and are given
in lineal gain chart (see Figure 6).
Lineal gain is actual measurable length of a part after two or more
parts are connected.
127055-01E

VENTING INSTALLATION

Air Inlet
Vent Hood
Eyebrow
Required for
Wall Installation
Superiorfireplaces.US.com
WARNING: The opening in collar around chimney
at top of fireplace must not be obstructed. Never use
blown insulation to fill chimney enclosure
3
12 / "
8
Galvanized
Outer Pipe
8" Stainless
Inner Pipe
Figure 6 - Lineal Gain
LINEAL GAIN
PART NO. DESCRIPTION
42"
SS-8DM Starter Section
12-8DM
Pipe Section
12-8HT
18-8DM
Pipe Section
18-8HT
24-8DM
Pipe Section
24-8HT
36-8DM
Pipe Section
36-8HT
48-8DM
Pipe Section
48-8HT
RT-8DM Round Termination
RTL-8DM Round Termination
RLT-8DM Round Termination
Round Termination
RTT-8DM
with Slip Section
Round Termination
RTTL-8DM
with Slip Section
Round Termination
RLTT-8DM
with Slip Section
ET-8DM Square Chase-Top
Square Chase-Top
ETO-8DM
with Mesh
Square Chase-Top
ETL-8DM
with Slip Section
Square Chase-Top
ETLO-8DM with Mesh & Slip
* The lineal gain for the terminations is
measured to the lue gas outlet height.
.
Hemmed
End
GAIN
Fireplace 45"
19''
10 5 / "
8
16 5 / "
8
5
23 / "
8
34 5 / "
8
46 5 / "
8
7
6 / "*
8
7 3 / "*
4
7 1 / "*
2
7
6 / " to
8
1
23 / "*
8
1
8 / " to
2
21 1 / "*
2
7 1 / " to
2
1
21 / "*
4
12"*
12"*
7" to 15"*
12" to
25 1 / "*
2
Section
7