SERVICE MANUAL CD RECEIVER MA047 2004 KD-SHX701, KD-SHX701T KD-SHX701 Area suffix E ---------- Continental Europe KD-SHX701T Area suffix E ---------- Continental Europe SOURCE KD-SHX701 EX -------------- Central Europe TP/PTY BAND EU ------------------------- Turkey BACK DISP MENU TABLE OF CONTENTS PRECAUTIONS ............... 1-3 SPECIFIC SERVICE INSTRUCTIONS .
Page 2
SPECIFICATION AUDIO AMPLIFIER SECTION Maximum Power Output Front 50 W per channel Rear 50 W per channel 19 W per channel into 4 Ω, 40 Hz to 20 000 Hz at no more Continuous Power Output Front (RMS) than 0.8% total harmonic distortion. 19 W per channel into 4 Ω, 40 Hz to 20 000 Hz at no more Rear than 0.8% total harmonic distortion.
SECTION 1 PRECAUTIONS Safety Precautions Burrs formed during molding may be left over on some parts of the chassis. Therefore, pay attention to such burrs in the case of preforming repair of this system. Please use enough caution not to see the beam directly or touch it in case of an adjustment or operation check.
Page 4
Preventing static electricity Electrostatic discharge (ESD), which occurs when static electricity stored in the body, fabric, etc. is discharged, can destroy the laser diode in the traverse unit (optical pickup). Take care to prevent this when performing repairs. 1.2.1 Grounding to prevent damage by static electricity Static electricity in the work area can destroy the optical pickup (laser diode) in devices such as CD players.
Page 5
Important for laser products 5.CAUTION : If safety switches malfunction, the laser is able 1.CLASS 1 LASER PRODUCT to function. 2.DANGER : Invisible laser radiation when open and inter 6.CAUTION : Use of controls, adjustments or performance of lock failed or defeated. Avoid direct exposure to beam. procedures other than those specified here in may result in 3.CAUTION : There are no serviceable parts inside the hazardous radiation exposure.
SECTION 3 DISASSEMBLY Main body section 3.1.1 Removing the front panel assembly (See Fig.1) (1) Push the detach button in the lower right part of the front Front panel assembly panel assembly. (2) Remove the front panel assembly. Detach button Fig.1 3.1.2 Removing the heat sink (See Fig.2)
3.1.3 Removing the top chassis assembly (See Figs.3 to 6) • Prior to performing the following procedures, remove the heat sink. Bottom chassis assembly Reference: Remove the front panel assembly as required. (1) From the bottom side of the main body, remove the two screws C attaching the top chassis assembly to the bottom chassis assembly.
Page 9
3.1.4 Removing the front chassis (See Figs.7 and 8) • Prior to performing the following procedure, remove the front Top chassis assembly panel assembly, heat sink and top chassis assembly. (1) From the both sides of the top chassis assembly, remove the two screws E attaching the front chassis.
Page 10
3.1.6 Removing the main board (See Figs.10 and 11) • Prior to performing the following procedures, remove the front Rear bracket panel assembly, heat sink and top chassis assembly. (1) From the rear side of the bottom chassis assembly, remove the two screws G attaching the rear bracket to the bottom chassis assembly.
Page 11
3.1.8 Removing the front door mechanism assembly (See Fig.13) • Prior to performing the following procedures, remove the front Front door mechanism assembly panel assembly, heat sink, top chassis assembly and main Bottom chassis board. (1) From the top side of the bottom chassis assembly, remove the screw K attaching the shaft holder to the bottom chas- sis.
Page 12
CD mechanism assembly • Prior to performing the following procedure "Removing the CD mechanism assembly". 3.2.1 Removing the front-end board (See Fig.1) (1) From the top side of the CD mechanism assembly, solder Short-circuit point Feed motor the short-circuit point on the flexible wire extending from the CD pickup.
Page 13
3.2.2 Removing the top cover (See Fig.2) (1) From the back side of the CD mechanism assembly, re- move the two screws B attaching the top cover. Top cover (2) Take out the top cover upward. Parts d Reference: When reassembling the top cover, set parts c of the top cover under the bending parts d of the chassis base.
Page 14
3.2.4 Removing the clamper unit (See Figs.5 and 6) • Prior to performing the following procedures, remove the top Clamper unit cover and mechanism section. (1) From the bottom of the mechanism section, remove the clamper spring2. (See Fig.5) (2) Release part e of the clamper spring from the bending part of the chassis base assembly.
Page 15
3.2.5 Reattaching the clamper unit (See Figs.5 to 9) (1) From the bottom of the mechanism section, attach the Clamper2 spring clamper spring2 to the clamper unit. (See Figs.5 and 7) (2) Move the clamper unit to set the side joints f and g to each boss of the chassis base.
Page 16
3.2.6 Removing the front unit (See 10 to 12) • Prior to performing the following procedures, remove the top Front-end cover and mechanism section. board (1) From the bottom side of the mechanism section, discon- nect the flexible wire from connector CN503 on the front- end board.
Page 17
3.2.7 Removing the loading arm S.A. (See Figs.13 and 14) • Prior to performing the following procedures, remove the top cover, mechanism section and front unit. (1) From top side of the front unit, move the loading arm S.A. from the front upwards. (See Fig.13) (2) Release the bosses from the right and left joints m and n of the chassis base.
Page 18
3.2.8 Removing the rod (L)(R) and roller assembly (See Figs.15 and 16) • Prior to performing the following procedures, remove the top Collar Collar cover, mechanism section, front unit and loading arm S.A. (1) From the bottom side of the loading arm S.A., release the rod (L) and (R) from the joints r.
Page 19
3.2.9 Removing the CD pickup assembly (See Figs.17 to 19) • Prior to performing the following procedure, remove the front- Feed gear end board. CD Pickup assembly (1) From the bottom of the CD mechanism assembly, turn the feed gear in the direction of the arrow to move the CD pick- up assembly outwards.
Page 20
3.2.10 Removing the spindle motor (See Fig.20) • Prior to performing the following procedure, remove the front- T. table assembly end board. (1) From the bottom side of the CD mechanism assembly, re- Washer move the T.table assembly and washer from the spindle motor.
Page 21
3.2.12 Removing the SW board and reset SW board (See Fig.23) • Prior to performing the following procedure, remove the front- end board. (1) From the top side of the CD mechanism assembly, remove the screw L attaching the SW board. (2) Remove the screw M attaching the reset SW board.
(2) Electric voltmeter Load impedance 20KΩ(2 Speakers connection) (3) Digital tester Output Level (4) Tracking offset meter (5) Test Disc JVC :CTS-1000 KD-AR7000 Line out 5.0V (Vol. MAX) (6) Extension cable for check KD-SHX700 Line out 4.0V (Vol. MAX) EXTSH002-22P × 1...
Page 23
Service mode 4.2.1 Service mode setting (1) Push POWER BOTTON (Power ON) (2) Set to service mode By pushing and holding "DISP" button + "VOLUME +" button + "MENU" button sequentially. "SOURCE" button "OK" button "CURSOR" button SOURCE PICT BAND BACK DISP MENU...
Page 24
CD DATA READ ADJ NOW ADJ INT OTHERS ADJ NOW ADJ NOW FEB ** FEO ** TEB ** RFG** The auto adjustment value of FGA ** TEO ** TGA ** survo at now ADJ INT ADJ INT FEB ** FEO ** TEB ** RFG** The auto adjustment value of FGA ** TEO ** TGA ** RUNNING MODE...
Page 25
PICTURE CLEAR NOW... PICTURE CLEAR A.DSP ERROR CLEAR NOW... A.DSP ERROR CLEAR T.DSP ERROR CLEAR NOW... T.DSP ERROR CLEAR ROM COLLECTION DATA READ DATA CLEAR DATA READ (Without disk) If "DISP" and "SOURCE" buttons are pushed and PLEASE INSERT DATA CD held during the usual display, it will shift to ROM COLLECTION.
Page 26
SMTH1=****** SMTH1=****** SMTH1=****** DEFAULT * BACK / DISP Change the value with ENTER : OK / BAND "CURSOR" button. SMTH2=****** SMTH2=****** SMTH2=****** DEFAULT * BACK / DISP Change the value with ENTER : OK / BAND "CURSOR" button. MP=****** MP=****** MP=****** DEFAULT * BACK / DISP Change the value with...
Page 27
7.FM IF COUNTER 7.FM COUNTER 97.9MHz 70dBuV 0% 97.9MHz 70dBuV 0% Adjustment NG or No Signal 8.AM S.METER 8.AM S.METER 999kHz 26dBuV 0% 999kHz 26dBuV 0% High or Low or No Signal 9.AM S.METER 9.AM S.METER 999kHz 56dBuV 0% 999kHz 56dBuV 0% High or Low or No Signal 10.AM IF COUNTER 10.AM IF COUNTER...
Page 28
4.2.2 Detailed CD error code Error Details of error Error code Detailed error code Focus serch error When foucus is not adjusted by 3-round(1set) focus serch after 0053 Focus is not adjusted by disc change or focus shock, 3-round focus serch the result is NG Tracking balance adjustment error Tracking balance adjustment is...
Page 29
4.2.3 Detailed error code of mechanism error Error Details of error Error code Detailed error code Disc loading error 1.B1 Time out 0011 2.C1 Time out 0012 3.D1 Time out 0013 4.C2 Time out 0014 5.B2 Time out 0015 6.A2 Time out 0016 7.F1 Time out 0017...
Page 30
4.2.5 Detailed CD changer mechanisum error code Details of error Error code Error Detailed error code Tray extension error 1.Tray-in switch time out Tray stops part way 0011 (Tray-in switch Low,Tray-out switch High) 2.Tray-out switch time out Tray stops part way 0012 (Tray-in switch High,Tray-out switch High) 3.Tray-in switch time out...
Page 31
4.2.6 Detailed CD changer error code Error Details of error Error code Detailed error code Pickup movement error Time over at PUBWD and PUFWD by monitoring RESET SW 1.Time over of pickup movement Pickup cannot move to an inner around inner circumference (10s) circumference.
SECTION 5 TROUBLESHOOTING Feed section Is the wiring for IC601 Is 8V present at IC681 Is 2V at IC601 pin 63? Check CD8V. pin 63 correct? pins 3 and 12? Check the vicinity of IC601. Is 4V present at both Is 2V present at IC681 Check the feed motor sides of the feed motor?
Page 33
Signal processing section Compare the L-ch and Is the sound output from No sound from either R-ch to locate the both channels (L, R)? channel. defective point. Normal Is 9V present at IC165 Is 9V present at IC901 Check IC901 and its /IC265 pin 16? pin 10? peripheral circuits.
Page 34
Maintenance of laser pickup Replacement of laser pickup (1) Cleaning the pick up lens Before you replace the pick up, please try to clean the lens Turn of the power switch and, disconnect the with a alcohol soaked cotton swab. power cord.
Page 35
16P CORD DIAGRAM GN/BK WH/BK VI/BK GY/BK Black Green Violet Blue Gray BL/WH White Yellow OR/WH Orange Brown VI/BK GY/BK MEMORY OR/WH WH/BK BL/WH REMOTE GN/BK VI/BK GY/BK BL/WH OR/WH WH/BK GN/BK Rear Right Auto Antenna Front Right Line Front Left Telephone Muting...
Page 36
VICTOR COMPANY OF JAPAN, LIMITED AV & MULTIMEDIA COMPANY CAR ELECTRONICS CATEGORY 10-1,1chome,Ohwatari-machi,Maebashi-city,371-8543,Japan (No.MA047) Printed in Japan...
PARTS LIST [ KD-SHX701 ] [ KD-SHX701T ] * All printed circuit boards and its assemblies are not available as service parts. KD-SHX701 Area suffix E ----------- Continental Europe KD-SHX701T Area suffix E ----------- Continental Europe EX --------------- Central Europe...
Page 38
Exploded view of general assembly and parts list Block No. Front board 50 51...
Page 40
General Assembly Block No. [M][1][M][M] Symbol No. Part No. Part Name Description Local GE20156-002A GEAR BKT UNIT LV40847-002A SPACER FSYH4036-100 SHEET GE30968-001A LEVER BKT UNIT GE30964-002A LOWER LEVER ASS GE30975-003A FRONT BKT ASSY QNZ0664-002 CAR CONNECTOR QAL0587-001 FSYH4036-100 SHEET GE30972-001A DETACH LEVER GE30973-001A...
Page 41
Symbol No. Part No. Part Name Description Local LV43889-001A SW PWB SHEET LV40848-050A SPACER(P) LV34937-001A NAME PLATE SHX701E LV35345-001A NAME PLATE SHX701TE,SHX701TEU,SHX701TEX LV41843-002A LASER CAUTION GE40218-011A SHEET (x2) GE40101-001A PIN CAP (x8) QJJ010-040904 SIN CR C-C WIR QUQ105-3003AB FFC WIRE LV43349-001A POWE IC BKT LV43373-001A...
Page 42
CD mechanism assembly and parts list Block No. FLM-JC1-1D Grease = JVS-1003 = MOBIL-1 = JVG-31N = JC-803B 61 38 11.10mm 0.10mm 82 82 1.2 0.1mm...
Page 43
CD mechanism Block No. [M][B][M][M] Symbol No. Part No. Part Name Description Local VKZ4539-026 MINI SCREW (x5) LV10857-001A CHASSIS FRAME 2 LV30225-0J6A SPACER (x2) LV35272-001A DAMPER(F) (x2) LV35273-001A DAMPER(R) QYSPSTU2045M TAP SCREW M2 x 4.5mm(x3) LV43039-001A DAMPER SP.(R) LV43849-001A DAMPER SP(F2) (x2) LV43041-001A...
Page 44
Symbol No. Part No. Part Name Description Local LV43011-001A THRUST SPRING QYSPSFT2040Z TAP SCREW M2 x 4mm LV21604-003A L.S.HOLDER 1 VKZ4539-026 MINI SCREW (x2) LV34582-002A L.S.HOLDER 2 VKZ4539-026 MINI SCREW (x2) LV34581-001A SUB GUIDE VKZ4539-026 MINI SCREW (x3) LV34915-001A SW LEVER LV43898-001A S.L.SPRING...
Electrical parts list Main board Symbol No. Part No. Part Name Description Local Block No. [0][1][0][0] D715 UDZS5.6B-X Z DIODE 1.5kΩ 1/10W J Symbol No. Part No. Part Name Description Local D716 UDZS5.6B-X Z DIODE 1.5kΩ 1/10W J D717 UDZS5.6B-X Z DIODE...
Page 46
Symbol No. Symbol No. Part No. Part Name Description Local Part No. Part Name Description Local NRSA63J-473X MG RESISTOR 47kΩ 1/16W J C987 QERF1CM-107Z E CAPACITOR 100uF 16V M NCB31EK-223X C CAPACITOR 0.022uF 25V K C988 NCB31HK-103X C CAPACITOR 0.01uF 50V K NCB31HK-103X C CAPACITOR...
Page 47
Symbol No. Symbol No. Part No. Part Name Description Local Part No. Part Name Description Local C2723 QERF1AM-107Z E CAPACITOR 100uF 10V M NRSA63J-222X MG RESISTOR 2.2kΩ 1/16W J C2724 NCB31HK-152X C CAPACITOR 1500pF 50V K NRSA63J-0R0X MG RESISTOR 0Ω...
Page 48
Symbol No. Symbol No. Part No. Part Name Description Local Part No. Part Name Description Local R757 NRSA63J-102X MG RESISTOR 1kΩ 1/16W J R991 NRSA63J-102X MG RESISTOR 1kΩ 1/16W J R758 NRSA63J-473X MG RESISTOR 47kΩ 1/16W J R1000 NRS181J-0R0X MG RESISTOR 0Ω...
Page 49
Symbol No. Symbol No. Part No. Part Name Description Local Part No. Part Name Description Local R2626 NRSA63J-123X MG RESISTOR 12kΩ 1/16W J R4134 NRSA63J-102X MG RESISTOR 1kΩ 1/16W J R2651 NRSA63J-0R0X MG RESISTOR 0Ω 1/16W J R4135 NRSA63J-102X MG RESISTOR 1kΩ...
Symbol No. Symbol No. Part No. Part Name Description Local Part No. Part Name Description Local TH901 NAD0036-224X N THERMISTOR 220kΩ C806 NCB31HK-102X C CAPACITOR 1000pF 50V K Ω TH902 NAD0031-002X N THERMISTOR C807 NCB31CK-473X C CAPACITOR 0.047uF 16V K ...
Page 51
Symbol No. CD module board Part No. Part Name Description Local Block No. [0][3][0][0] R822 NRSA63J-821X MG RESISTOR 820Ω 1/16W J Symbol No. R823 NRSA63J-102X MG RESISTOR 1kΩ 1/16W J Part No. Part Name Description Local R825 NRSA63J-471X MG RESISTOR 470Ω...
Page 52
Symbol No. Symbol No. Part No. Part Name Description Local Part No. Part Name Description Local C638 NCB31HK-103X C CAPACITOR 0.01uF 50V K R533 NRSA63J-101X MG RESISTOR 100Ω 1/16W J C639 NEA70JM-476X E CAPACITOR 47uF 6.3V M R534 NRSA63J-101X MG RESISTOR 100Ω...
Page 53
Symbol No. Part No. Part Name Description Local R642 NRSA63J-103X MG RESISTOR 10kΩ 1/16W J R643 NRSA63J-332X MG RESISTOR 3.3kΩ 1/16W J R651 NRSA63J-104X MG RESISTOR 100kΩ 1/16W J R653 NRSA63J-0R0X MG RESISTOR 0Ω 1/16W J R654 NRSA63J-470X MG RESISTOR 47Ω...
Page 54
Packing materials and accessories parts list Block No. A1 A3 A4 A5 A6 A7 A8 A9 A10 A11 A12 KIT : A13 A14 A16 A17 3-18...
Page 55
Packing and Accessories Block No. [M][3][M][M] Symbol No. Part No. Part Name Description Local LVT1159-004A INST BOOK ENG SPA FRE TUR SHX701TEU LVT1159-001A INST BOOK ENG GER FRE DUT SHX701E,SHX701TE,SHX701TEX LVT1159-002A INST BOOK SPA ITA POL RUS SHX701E,SHX701TE LVT1159-005A INST BOOK SHX701TEU LVT1159-003A...
SCHEMATIC DIAGRAMS CD RECEIVER KD-SHX701,KD-SHX701T CD-ROM No.SML200405 KD-SHX701 Area suffix E ---------- Continental Europe KD-SHX701T Area suffix E ---------- Continental Europe SOURCE KD-SHX701 EX -------------- Central Europe TP/PTY BAND EU ------------------------- Turkey BACK DISP MENU Contents Block diagram Standard schematic diagrams...
Safety precaution Burrs formed during molding may be left over on some parts of the chassis. Therefore, pay attention to such burrs in the case of preforming repair of this system. Please use enough caution not to see the beam directly or touch it in case of an adjustment or operation check.
Standard schematic diagrams DSP section Parts are safety assurance parts. When replacing those parts make sure to use the specified one. blend iboc_i 0.022 10/6.3 iboc_q iboc_ws IDM_DATA iboc_bck IDM_WS IDM_BCK LINE.IN-L LINE.IN-GND LINE.IN-R RDS-D2 SUBWFER RDS-C2 SCL-DI 10/6.3 RDS_DATA SDA-DI IC10 RDS_CLK...
Page 67
VICTOR COMPANY OF JAPAN, LIMITED AV & MULTIMEDIA COMPANY CAR ELECTRONICS CATEGORY 10-1,1chome,Ohwatari-machi,Maebashi-city,371-8543,Japan Printed in Japan (No.MA047SCH)