Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Wonwoo PS-M032
Summary of Contents for Wonwoo PS-M032
- Page 1 INSTALLATION / OPERATING MANUAL 3x Mega pixel HD-SDI Mini Speed Dome camera P/N : 388059105 PRINTED IN KOREA Distributed by Before attempting to connect or operate this product, please read these instructions carefully and save this manual for future use...
-
Page 2: Table Of Contents
TABLE OF CONTENTS 1. PRECAUTIONS 1. 1 Important Safety Instruction 1. PRECAUTIONS • Read these instructions. 1. 1 Important Safety Instruction ................... • Pay attention on all the warnings. 2. GETTING STARTED • Follow all instructions. 2. 1 Features ........................ •... -
Page 3: Getting Started
2. GETTING STARTED 2. 1 Features 2. 3 Selection Flow Auto-Focus - The camera adjusts the focus automatically while monitoring the screen continuously Type Indoor Outdoor in the auto mode. It built in 3x zoom lens, when used in combination with its 6x digital zoom, the camera achieves a zooming capability of up to 18x. -
Page 4: Installation
3.Installtion 3. 1 Address / communication setting 3. 3 Indoor Ceiling The following steps of installation and connection work should be done by qualified service personnel or system installers and should conform to all local codes. ▶ ADDRESS( ID) setting S/W NO ▶... -
Page 5: Indoor In Ceiling
3. 4 Indoor In Ceiling 3. 5 Outdoor (Ceiling Bracket) The mounting has to be installed onto a firm and stable location where all the parts may be completely The mounting has to be installed onto a firm and stable location where all the parts may be completely secured. -
Page 6: Outdoor (Wall Bracket)
4. MAIN SETUP MENU 4. 1 Initialize 3. 6 Outdoor (Wall Bracket) The mounting has to be installed onto a firm and stable location where all the parts may be completely When the device is powered on, you can check the address, secured. - Page 7 - LABEL Setting - TOUR NO Press key. NEAR TOUR MENU PRESET LABEL EDIT <001> TOUR MENU Select character by using joystick and press key. NEAR LABEL : PRESET 001 TOUR NO : 01 DEFINE LABEL TOUR EDIT < > <STORE TELE MOVE...
- Page 8 3) Scan - Start POSITIION By using Scan function, the camera moves between 2 positions if there is no PTZ command after SCAN MENU SCAN START POSITION passing the assigned Dwell time. When there is no camera movement, the Scan function runs and the camera moves from the position assigned as the start point to the position assigned as the end point SCAN NO : 01 DEFINE...
- Page 9 - DWELL - LABEL The Scan function runs after the Dwell time without any camera SCAN MENU PATTERN LABEL EDIT <01> PATTERN MENU movement. SCAN NO : 01 DEFINE LABEL : PATTERN NO : 01 UNDEFINE Select ON/OFF by using joystick and press key.
- Page 10 - START PAN POSION 5) AREA The Area function means that it displays the Area name between two programmed pan positions. AREA MENU AREA START POSITION Maximun 16 Area functions are toured in order. AREA NO : 01 DEFINE LABEL START PAN POS : 000.0 STOP PAN POS...
- Page 11 - ALARM NO “Save” above setting Alarm data to the memory. ※ - "Save" above setting data to the memory. ALARM SELECT AREA MENU - "CLR" means above setting Pattern data will not be saved and be cleared. - "BACK" means it goes back to the previous menu. ALARM NO : 01 UNDEFINE LABEL...
-
Page 12: Dome Menu
4. 3 Dome Menu - TIME ＊TIME (MIN) : The Park time can be assigned from 10 sec to 60sec. (Max. 2min./ by 10 sec.) PARK MENU Pan, Tilt, Zoom motion is adjustable in the “Dome Setting” Menu. TIME : 02MIN MAIN MENU FUNCTION : PRESET... - Page 13 - RESPONSE 5) DOME SUB MENU *Send the intrinsic protocol value to the Tx line. (Only for Pelco-D 5.0) DOME MENU DOME MENU TILT LIMIT : OFF Select ON/OFF by using joystick and press key. NEAR TITLE : SPEED BY ZOOM : OFF POWER UP ACTION : ON AUTO FLIP...
- Page 14 - HEATER OFF TEMP 8) FATORY SET ＊Set the temerature of heater OFF. (0~70℃) Restore all of setting value to the factory default. DOME MENU DOME MENU HEATER ON TEMP : 5 C All of existing setting value would be erased. TITLE : HEATER ON TIME : 30 MIN...
-
Page 15: Camera Menu
- D-ZOOM 4. 4 Camera Menu Decide using of digital zoom function. D-ZOOM: ON/ OFF Camera menu is subject to be changed without prior notice to upgrade and quality increase and we may use slip sheet for the change. Select : Set ON : Set OFF : NEAR... - Page 16 - NEAR LIMIT - RED, BLUE MODE Infinity focus is the state where a lens from an image of Adjust color leverl (RED, BLUE : 00~ 20) an object an infinite distance away. Standard level : RED -> 10 BLUE->110 This corresponds to the point of focus for Select : Set ON :...
- Page 17 - SLOW SHUTTER 5) WDR MODE Select AUTO, MANUAL, SHUTTER or IRIS. Set WDR funtion WDR(Wide Dynamic Range) Select : NEAR Set ON : Set OFF : NEAR - SHUTTER - WDR MODE If you set SHUTTER in the AE MODE, you can control shutter Select ON or OFF.
- Page 18 - ICR AUTO GAP 6) SPECIAL Select the ICR level. In the Special menu, it’s available to set special function of the camera Select : NEAR Set ON : Set OFF : NEAR Select : Set ON : Set OFF : NEAR NEAR - ICR AUTO DELAY...
-
Page 19: Clear Setting
- PRESET FREEZE 7) CAMERA RESET Display start image and finished image only. Make initialize the setting value which is set in CAMERA MENU. Static image on-screen during the camera movement. Select : NEAR Set ON : Set OFF : NEAR Select : NEAR... -
Page 20: Specification
Built-in Focus Control Auto / Manual / One push selectable Iris Control Auto / Manual selectable Protocols PELCO-D, PELCO-P , WONWOO Communication RS-485 Power Consumption AC 24V 3A(OUTDOOR), AC 24V 1A(INDOOR), DC 12V 1.5A(INDOOR) Operating Temperature 0ºC ~ +50ºC (Indoor ) Ø107.5... - Page 21 Ø128 Ø4.5 Ø180.3 Ø107.5 R53.8 Ø172 Ø164 Ø128 Ø4.5 161.6 132.4 Ø180.3 R53.8 R53.8 Ø172...
- Page 22 MEMO...
Need help?
Do you have a question about the PS-M032 and is the answer not in the manual?
Questions and answers