Rigol DS6000 User Manual
Digital, demo board
Hide thumbs
Also See for DS6000:
- User manual (298 pages) ,
- Quick manual (41 pages) ,
- Service manual (26 pages)
Related Manuals for Rigol DS6000
Summary of Contents for Rigol DS6000
- Page 1 RIGOL User’s Guide DS6000 Digital Oscilloscope Demo Board July 2011 RIGOL Technologies, Inc. GlobalTestSupply www. .com Find Quality Products Online at: sales@GlobalTestSupply.com...
-
Page 2: Table Of Contents
3.3.1 RS232/UART Signal .................... 3-35 3.3.2 SPI Signal ......................3-38 3.3.3 I2C Signal ......................3-40 3.3.4 CAN Signal ......................3-42 3.3.5 Signals for Testing Logic Analyzer ................ 3-43 GlobalTestSupply User’s Guide for DS6000 Demo Board www. .com Find Quality Products Online at: sales@GlobalTestSupply.com... -
Page 3: Chapter 1 Overview
RIGOL Chapter 1 Overview This manual introduces the functions and using methods of DS6000 Demo board. This Demo board is used to illustrate the basic functions of the oscilloscope. It is powered through USB port and can output 25 kinds of signals for the illustration of oscilloscope functions. -
Page 4: Chapter 2 Quick Start
2.1 Demo Board Layout Part1 Part3_E Part2 Part2_E Part8 Part9 Part3 Part3_E Part4 Part4_E Part6 Part7_S Part7_E Part10 Part5_E Part5_S Part5 Figure 2-1 Board Layout GlobalTestSupply User’s Guide for DS6000 Demo Board www. .com Find Quality Products Online at: sales@GlobalTestSupply.com... - Page 5 Crosstalk signal 2 output each time the SINGLE key is pressed. Part2_E RARE_AN Part2 pins extension —— FREQ_AN —— MANU_AN —— MANU_BST —— GLITCH_SINE —— GLITCH_CLK —— GlobalTestSupply User’s Guide for DS6000 Demo Board www. .com Find Quality Products Online at: sales@GlobalTestSupply.com...
- Page 6 SPI MOSI signal I2C_SDA I2C data signal Output signal of I2C data bus. The content of the data is the character string “RIGOL” but the data frame head and read/write bits will change. I2C_SCL I2C clock signal Clock signal of I2C protocol. The clock frequency is 125kHz.
- Page 7 10% overshoot. Part5_S SLOW Slow sweep Select “Slow” or “Fast” sweep. FAST Fast sweep Part5_E DAC_OUT Part5 —— pins extension UF_DAC SWEEP NOISY_SINE SINE SQUARE GlobalTestSupply User’s Guide for DS6000 Demo Board www. .com Find Quality Products Online at: sales@GlobalTestSupply.com...
- Page 8 LA_D11 Output 6.1kHz square waveform. LA_D12 Output 3.05kHz square waveform. LA_D13 Output 1.525kHz square waveform. LA_D14 Output 762.2Hz square waveform. LA_D15 Output 381.1Hz square waveform. GlobalTestSupply User’s Guide for DS6000 Demo Board www. .com Find Quality Products Online at: sales@GlobalTestSupply.com...
- Page 9 24 bits digital input terminal. It can input digital terminal data stream and be used for function extension. Part10 —— USB Device USB port, used for demo board power supply. GlobalTestSupply User’s Guide for DS6000 Demo Board www. .com Find Quality Products Online at: sales@GlobalTestSupply.com...
-
Page 10: Measurement Connection
Demo board damage and the board should be used in anti-static environment as far as possible. GlobalTestSupply User’s Guide for DS6000 Demo Board www. .com Find Quality Products Online at:... -
Page 11: Chapter 3 Demo Board Applications
“+Duty” and “Vpp” measurements and enable statistic function. The demonstration result is as shown in the figure below. Duty Cycle Measurement Figure 3-1 Demonstration Result of Square Waveform GlobalTestSupply User’s Guide for DS6000 Demo Board www. .com Find Quality Products Online at: sales@GlobalTestSupply.com... -
Page 12: Sine Signal
The demonstration result is as shown in the figure below. Figure 3-2 Demonstration Result of Sine Signal GlobalTestSupply User’s Guide for DS6000 Demo Board www. .com Find Quality Products Online at:... - Page 13 Enable “FFT” operation and the signal frequency is 500 kHz as shown in the figure below. Figure 3-3 FFT Operation Result of Sine Signal GlobalTestSupply User’s Guide for DS6000 Demo Board www. .com Find Quality Products Online at: sales@GlobalTestSupply.com...
-
Page 14: Da Output Signal
DAC_IN5 DAC_IN4 DAC_IN3 DAC_IN2 DAC_IN1 DAC_IN0 Figure 3-4 Digital Input Signals Note: in the figure above, the probe ratio of CH1 and CH4 is “×10”. GlobalTestSupply User’s Guide for DS6000 Demo Board www. .com Find Quality Products Online at: sales@GlobalTestSupply.com... - Page 15 Unfiltered Sine Waveform Filtered Sine Waveform Figure 3-6 Analog Output Signal GlobalTestSupply User’s Guide for DS6000 Demo Board www. .com Find Quality Products Online at: sales@GlobalTestSupply.com...
-
Page 16: Differential Signal
The demonstration result is as shown in the figure below. Figure 3-7 Differential Signal Measurement Using Differential Probe GlobalTestSupply User’s Guide for DS6000 Demo Board www. .com Find Quality Products Online at:... - Page 17 Enable MATH function (A-B). Set source A to CH1 and source B to CH2. The operation result is as shown in the figure below. Figure 3-9 MATH Function Demonstration Using Single-ended Probe GlobalTestSupply User’s Guide for DS6000 Demo Board www. .com Find Quality Products Online at: sales@GlobalTestSupply.com...
-
Page 18: Pal Video Signal
“500 mV”; adjust the vertical position and trigger level to appropriate values to make the oscilloscope trigger stably. The demonstration result is as shown in the figure below. Figure 3-10 PAL Video Signal GlobalTestSupply User’s Guide for DS6000 Demo Board www. .com Find Quality Products Online at:... -
Page 19: Ntsc Video Signal
The demonstration result is as shown in the figure below. Figure 3-11 NTSC Video Signal GlobalTestSupply User’s Guide for DS6000 Demo Board www. .com Find Quality Products Online at:... -
Page 20: Amplitude Modulation Signal
“Normal”; adjust the vertical position and trigger level to appropriate values to make the oscilloscope trigger stably. The demonstration result is as shown in the figure below. Figure 3-12 Amplitude Modulation Signal GlobalTestSupply 3-10 User’s Guide for DS6000 Demo Board www. .com Find Quality Products Online at: sales@GlobalTestSupply.com... - Page 21 Enable FFT operation function. Set the vertical scale to 100mVrms/div and the center frequency to 500 KHz. The operation result is as shown in the figure below. Figure 3-13 FFT Operation Result of Amplitude Modulation Signal GlobalTestSupply User’s Guide for DS6000 Demo Board 3-11 www. .com Find Quality Products Online at:...
-
Page 22: Special Signal Applications
“500 mV”; adjust the vertical position and trigger level to appropriate values to make the oscilloscope trigger stably. The demonstration result is as shown in the figure below. Figure 3-14 Sine Signal Superimposed with Noise GlobalTestSupply 3-12 User’s Guide for DS6000 Demo Board www. .com Find Quality Products Online at: sales@GlobalTestSupply.com... - Page 23 “Vrms”, the vertical scale to “100 mVrms” and the horizontal scale to “62.5MHz”. The operation result is as shown in the figure below. 125MHz noise component Figure 3-16 FFT Operation Result of Noisy Sine Signal GlobalTestSupply User’s Guide for DS6000 Demo Board 3-13 www. .com Find Quality Products Online at:...
- Page 24 The operation result is as shown in the figure below (the noise component is basically rejected). The noise component is basically rejected Figure 3-18 FFT Operation Result after Noise Reject GlobalTestSupply 3-14 User’s Guide for DS6000 Demo Board www. .com Find Quality Products Online at: sales@GlobalTestSupply.com...
-
Page 25: Slow Sweep Signal
Figure 3-19 Slow Sweep Signal GlobalTestSupply User’s Guide for DS6000 Demo Board 3-15 www. .com Find Quality Products Online at:... - Page 26 Adjust the “Persistence Time” to 20s and the sweep trace of the sweep signal is clearly displayed as shown in the figure below. Figure 3-20 Sweep Trace of the Slow Sweep Signal GlobalTestSupply 3-16 User’s Guide for DS6000 Demo Board www. .com Find Quality Products Online at: sales@GlobalTestSupply.com...
-
Page 27: Fast Sweep Signal
Figure 3-21 Fast Sweep Signal GlobalTestSupply User’s Guide for DS6000 Demo Board 3-17 www. .com Find Quality Products Online at:... - Page 28 Adjust the “Persistence Time” to 500ms and the sweep trace of the sweep signal is clearly displayed. Figure 3-22 Sweep Trace of the Fast Sweep Signal GlobalTestSupply 3-18 User’s Guide for DS6000 Demo Board www. .com Find Quality Products Online at: sales@GlobalTestSupply.com...
-
Page 29: Phase Deviation Signal
Enable delay measurement of the rising edge as well as statistic function. The demonstration result is as shown in the figure below. Figure 3-23 Channel Delay Measurement GlobalTestSupply User’s Guide for DS6000 Demo Board 3-19 www. .com Find Quality Products Online at:... -
Page 30: Rare Abnormal Signal
180kHz, the memory depth to “Auto”. Set the persistence time to 20s and the capture result of abnormal signal is as shown in the figure below. Rare Abnormal Signal Figure 3-24 Rare Abnormal Signal GlobalTestSupply 3-20 User’s Guide for DS6000 Demo Board www. .com Find Quality Products Online at: sales@GlobalTestSupply.com... - Page 31 Enable the waveform record function. After the record finishes, use the waveform playback and analysis function to analyze the accidental pulse. Figure 3-25 Waveform Record and Analysis GlobalTestSupply User’s Guide for DS6000 Demo Board 3-21 www. .com Find Quality Products Online at:...
-
Page 32: Frequent Abnormal Signal
500mV. At this point, the abnormal signals can be observed stably as shown in the figure below. Figure 3-26 Stable Display of Frequent Abnormal Signal GlobalTestSupply 3-22 User’s Guide for DS6000 Demo Board www. .com Find Quality Products Online at: sales@GlobalTestSupply.com... - Page 33 Enable Pass/Fail mode. Set X mask to 0.24div and Y mask to 0.50div. The demonstration result is as shown in the figure below. Figure 3-27 Pass/Fail Test of Frequent Abnormal Signal GlobalTestSupply User’s Guide for DS6000 Demo Board 3-23 www. .com Find Quality Products Online at:...
-
Page 34: Manual Abnormal Signal
“1 V”; adjust the vertical position and trigger level to appropriate values. The demonstration result is as shown in the figure below. Figure 3-28 Manual Abnormal Signal GlobalTestSupply 3-24 User’s Guide for DS6000 Demo Board www. .com Find Quality Products Online at: sales@GlobalTestSupply.com... -
Page 35: Manual Burst Signal
Set the time base to 5ms. At this point, the sample rate is 2GSa/s and the memory depth is 140Mpts. Under single trigger, every burst can be captured as shown in the figure below. Figure 3-29 Manual Burst Signal GlobalTestSupply User’s Guide for DS6000 Demo Board 3-25 www. .com Find Quality Products Online at:... - Page 36 Adjust the time base to 200ns/div when the oscilloscope is in STOP state and amplify the waveform captured. As shown in the figure below, all the waveform details are successfully captured. As DS6000 provides a 140Mpts deep memory, users can adjust the horizontal position to view relatively longer waveform stored. Figure 3-30 Burst Details...
-
Page 37: Narrow Burst Signal
“1 V”; adjust the vertical position and trigger level to appropriate values. The demonstration result is as shown in the figure below. Figure 3-31 Narrow Pulse GlobalTestSupply User’s Guide for DS6000 Demo Board 3-27 www. .com Find Quality Products Online at:... -
Page 38: Glitch Signal Of Sine
The demonstration result is as shown in the figure below and users can view the interval time between glitches. All the adjacent glitches can be captured. Figure 3-32 Sine Glitch Signal GlobalTestSupply 3-28 User’s Guide for DS6000 Demo Board www. .com Find Quality Products Online at: sales@GlobalTestSupply.com... - Page 39 Set the time base to 2us. The demonstration result is as shown in the figure below and the positions of the glitches on the sine waveform are clearly displayed. Figure 3-33 Sine Glitch Signal (Details) GlobalTestSupply User’s Guide for DS6000 Demo Board 3-29 www. .com Find Quality Products Online at:...
-
Page 40: Glitch Signal Of Square Waveform
“Normal” and the vertical scale to “500 mV”; adjust the vertical position and trigger level to appropriate values. The demonstration result is as shown in the figure below. Figure 3-34 Square Waveform Glitch Signal GlobalTestSupply 3-30 User’s Guide for DS6000 Demo Board www. .com Find Quality Products Online at: sales@GlobalTestSupply.com... - Page 41 2us; the demonstration result is as shown in the figure below and users can view the interval time between glitches. Figure 3-35 Time Interval between Glitches GlobalTestSupply User’s Guide for DS6000 Demo Board 3-31 www. .com Find Quality Products Online at: sales@GlobalTestSupply.com...
-
Page 42: Crosstalk Signal
As the frequency measurement result in the figure shows, the frequency of the signal is 1 MHz. Figure 3-36 CTALK_A and CTALK_B Output Signals GlobalTestSupply 3-32 User’s Guide for DS6000 Demo Board www. .com Find Quality Products Online at: sales@GlobalTestSupply.com... - Page 43 Enable the 20MHz bandwidth limit of CH1 and press SINGLE to trigger the 125 MHz high-frequency signal. The demonstration result is as shown in the figure below. Figure 3-38 Enable 20MHz Bandwidth of CH1 GlobalTestSupply User’s Guide for DS6000 Demo Board 3-33 www. .com Find Quality Products Online at:...
- Page 44 Enable the 20MHz bandwidth limit of CH2 and press SINGLE to trigger the 125 MHz high-frequency signal. The demonstration result is as shown in the figure below. Figure 3-39 Enable 20MHz Bandwidth Limit of CH2 GlobalTestSupply 3-34 User’s Guide for DS6000 Demo Board www. .com Find Quality Products Online at: sales@GlobalTestSupply.com...
-
Page 45: Digital Signal Applications
Stop bit is always 1bit, 1.5bits or 2bits. For this Demo board, the stop bit of RS232 signal is 1bit. 2. Signal Explanation Signal Output Pin: RS232_TX Rate: 9600bps; Data: RIGOL DS6000; Frame structure: 1bit start bit+ 8bits data bits+ 1bit stop bit; LSB output; negative polarity, none (check bit) 3. Functions RS232 trigger, RS232 decoding 4. - Page 46 Set the trigger condition to “Data” and the data to “54” (the ASCII code value of “6”). The corresponding data can be captured stably. Figure 3-41 RS232 Trigger and Decoding (Data Trigger) GlobalTestSupply 3-36 User’s Guide for DS6000 Demo Board www. .com Find Quality Products Online at: sales@GlobalTestSupply.com...
- Page 47 Note: the output signal of pin UART is the same with the RS232_TX signal except that its polarity is positive. The same demonstration result can be obtained using the above method (set the polarity to “+” in protocol decoding). GlobalTestSupply User’s Guide for DS6000 Demo Board 3-37 www. .com Find Quality Products Online at: sales@GlobalTestSupply.com...
-
Page 48: Spi Signal
SCLK to “CH1”, MOSI to “CH2”, the data bits to 8, the endian to MSB and the ary to hex. Set the BUS status to “ON” and the demonstration result is as shown in the figure on the next page. GlobalTestSupply 3-38 User’s Guide for DS6000 Demo Board www. .com Find Quality Products Online at:... - Page 49 Chapter 3 Demo Board Applications RIGOL Figure 3-43 SPI Trigger and Decoding GlobalTestSupply User’s Guide for DS6000 Demo Board 3-39 www. .com Find Quality Products Online at: sales@GlobalTestSupply.com...
-
Page 50: I2C Signal
2. Signal Explanation Signal Output Pin: I2C_SCL, I2C_SDA I2C signal with 125 kHz rate. The content is “RIGOL”. The data frame head and the read/write bit would change. 3. Functions I2C trigger, I2C decoding 4. - Page 51 Chapter 3 Demo Board Applications RIGOL Figure 3-44 I2C Trigger and Decoding GlobalTestSupply User’s Guide for DS6000 Demo Board 3-41 www. .com Find Quality Products Online at: sales@GlobalTestSupply.com...
-
Page 52: Can Signal
2. Signal Explanation Signal Output Pin: CAN_L, CAN_H CAN signal with 1MHz signal rate. The data is the character string “RIGOL”; the data length is 5; the signal uses CRC check and does not have ACK segment. 3. Functions CAN trigger, CAN decoding 4. -
Page 53: Signals For Testing Logic Analyzer
CH2 of the oscilloscope using the probe. The demonstration result is as shown in the figure below. Figure 3-46 LA_D0 and LA_D1 Output Signals GlobalTestSupply User’s Guide for DS6000 Demo Board 3-43 www. .com Find Quality Products Online at:... - Page 54 CH1 and CH2 to “Leading” and “X”, respectively. The oscilloscope can trigger stably as shown in the figure below. Figure 3-47 LA_D0 and LA_D1 Output Signals (Pattern Trigger) GlobalTestSupply 3-44 User’s Guide for DS6000 Demo Board www. .com Find Quality Products Online at: sales@GlobalTestSupply.com...
Need help?
Do you have a question about the DS6000 and is the answer not in the manual?
Questions and answers