Extron electronics System 5 IP Series Setup Manual page 11

im Vertrieb von
System 5 IP Hardware Setup, cont'd
For infrared (IR) output, wire an IR Emitter (2 emitters,
maximum, per port) as shown below for a modulated signal
and ground.
IR/SERIAL OUT
A B C D
S G S G S G S G
G = Ground
S = Signal (IR)
White Striped Wire
See the System 5 IP Series User's Manual for details on how to set
up these ports for IR or RS-232 control.
c
CM/IR/SCP port — You can connect up to four Extron control
modules (IRCMs, ACMs, RCMs), one Extron IR Link infrared
signal repeater, and/or up to two Extron SCP 104 or SCP 226
control pads to this port to allow remote control of the
System 5 IP switcher or other items. A maximum of seven
devices can be connected to this port.
The SCP 104 or SCP 226 Secondary Control Panel replicates
most of the switcher's front panel controls. The control pad
can receive IR signals from an optional IR 402 remote control
and send them to the switcher. Control modules can be used to
control VCRs, DVD players, tape decks, a projector lift, or screen
control. Refer to the appropriate device's user's manual.
The control modules, IR Link, and SCPs can be daisy chained,
as shown in the following diagram. Extron CTL (Comm-Link)
cable is recommended for these connections. Use the following
diagram as a wiring guide.
www.camboard.de
2-6 System 5 IP Switchers • Hardware Setup
100'
(30.5 m)
IR Emitter 1
Tel. 07131 911201
Fax 07131 911203
CAMBOARD Electronics
A B
+V G
200' (61 m) max.
Extron CTL or CTLP Cable Color Code:
E SCP Communication
Modulated IR (for IR Link)
D
Control Module Communication
C
B Ground ( ) & Drain Wire
+12 VDC
A
d
System 5 IP Switcher
C D E
Rear Panel
CM IRSCP
DISPLAY
E SCP Communication
PIC
ON OFF
MUTE
C IRCM, ACM, RCM
B Ground ( ) & Drain Wire
VOLUME
A +12 VDC
AUTO
IMAGE
to Last Device
Extron
SCP 226
Maximum =
4 Control Modules
= White
(4 Module Addresses)
Violet Control modules include IRCM,
=
Black & Drain Wire
= ACM, RCM, and CM models.
Red
=
N
The maximum total distance between the System 5 IP and
a connected device is 200' (61 m).
N
Extron recommends that you connect the cable's drain
wire to the ground pin at both ends. This reduces EMI
interference.
Relay ports — Via Global Configurator, each relay can be
associated with a front panel button (projector on/off buttons,
function buttons, or input selection buttons) or can be operated
independently.
Group A Group B
RELAYS RELAYS
A B C A
C 1 2 C 3 4 C 5 6 C 1 2 C
Common Relay 2 Common
Relay 1
These relays are normally open by default. They can be
configured via SIS commands or Global Configurator to operate
as follows:
• on — relay closes and stays closed until otherwise
instructed
• off — relay opens and stays open until otherwise instructed
ce-info@camboard.de
System 5 IP Switchers • Hardware Setup
DOC
PC VCR
CAM
1 2 3
4 5 6
DVD LAPTOP
IR
SCP 226
C IRCM/ACM/RCM
B Ground ( )
A +12 VDC
DVD & VCR CONTROL
Tx
DVD VCR
TITLE MENU
TUNER
ENTER TV/VCR
PREV/REW PLAY NEXT/FWD PAUSE STOP
IRCM-DV+
Group C
RELAYS
B C A B C
3 4 C 5 6 C 1 2 C 3 4 C 5 6
Relay 4 Common Relay 6
Relay 3 Relay 5
2-7