Table of Contents
Advertisement
nd is automatically defined as following table.
ectable indoor unit.
uto-RUN" mode
three step of air flow setting
ne of air flow setting
atically swing louver
omatically swing louver
step of air flow setting
ep of air flow setting
ne of air flow setting
05 EXTERNAL INPUT" and "06 PERMISSION /
Indoor unit air flow setting
-
-
-
-
-
e - Lo
Hi - Me - Lo
Hi - Lo
Hi - Me
Hi - Me
UH - Hi - Me
UH - Me
UH - Hi
t is "HIGH SPEED".
180 hours.
600 hours.
1000 hours.
1000 hours, then the indoor unit will be stopped by
",
tion "14
" accordingly.
e four.
will be valid.
door units connected with the same outdoor unit immediately.
-off terminal "CNT-6", all indoor units are stopped immediately.
n temperature during heating.
n temperature during heating.
n temperature during heating.
turn air temperature of indoor unit.
turn air temperature of indoor unit.
turn air temperature of indoor unit.
urn air temperature of indoor unit.
urn air temperature of indoor unit.
urn air temperature of indoor unit.
d is low speed.
d is set speed.
d is operated intermittently.
stopped.
N OFF" is set automatically.
s thermistor is working.
ure to start frost prevention control.
ap is raised.
eating.
ng and fan.
an.
at is OFF, the fan does not perform extra operation.
at is OFF, the fan perform extra operation for half an hour.
at is OFF, the fan perform extra operation for an hour.
at is OFF, the fan perform extra operation for six hours.
tat is OFF, the fan does not perform extra operation.
tat is OFF,the fan perform extra operation for half an hour.
tat is OFF,the fan perform extra operation for two hours.
tat is OFF, the fan perform extra operation for six hours.
ostat is OFF, the fan perform intermittent operation for five minutes
F.
ostat is OFF, the fan perform intermittent operation for five minutes
t, and is automatically defined.
AMP Air Conditioning
How to set function
Stop air-conditioner and press
(SET)
1.
buttons at the same time for over three seconds, and the
"FUNCTION SET
" will be displayed.
2.
Press
(SET) button.
3.
Make sure which do you want to set, "
(remote control function) or "I/U FUNCTION
function).
4.
Press
or
button.
Selecct "
FUNCTION
" (remote control function) or "I/U
FUNCTION
" (indoor unit function).
5.
Press
(SET) button.
6.
On the occasion of remote control function selection
"DATA LOADING" (Indication with blinking)
Display is changed to "01
Press
or
button.
"No. and function"are indicated by turns on the remote control
function table, then you can select from them.
(For example)
Function No.
Function
Press
(SET) button.
The current setting of selected function is indicated.
(for example) "AUTO RUN ON"
If "02 AUTO RUN SET" is
selected
Setting
Press
or
button.
Select the setting.
Press
(SET)
"SET COMPLETE" will be indicated, and the setting will be
completed.
Then after "No. and function" indication returns, Set as the
same procedure if you want to set continuously ,and if to
finish, go to 7.
7.
Press ON/OFF button.
Setting is finished.
It is possible to finish by pressing ON/OFF button on the way, but unfinished change of setting is
unavailable.
During setting, if you press
Setting is memorized in the control and it is saved independently of power failure.
How to check the current setting
When you select from "No. and funcion" and press set button by the previous operation, the "Setting" displayed first is the current
setting.
(But, if you select "ALL UNIT
", the setting of the lowest number indoor unit is displayed.)
Operation message
Function description:
(MODE)
setting description:
FUNCTION
"
" (indoor unit
1
6
Indoor unit selection button
On the occasion of indoor unit function selection
"DATA LOADING" (Blinking for 2 to 23 seconds to read the data)
".
Indication is changed to "02 FAN SPEED SET".
Go to
.
[Note]
(1)
If plural indoor units are connected to a remote control,
the indication is "I/U 000" (blinking)
the indoor unit connected is indicated.
(2)
Press
or
Select the number of the indoor unit you are to set
If you select "ALL UNIT
all unites.
(3)
Press
Press
or
"No. and function" are indicated by turns on the indoor unit function
table, then you can select from them.
(For example)
Press
(SET) button.
The current setting of selected function is indicated.
(For example) "STANDARD"
selected.
Press
or
Select the setting.
Press
(SET) button.
"SET COMPLETE" will be indicated, and the setting will be
completed.
Then after "No. and function" indication returns, set as the same
procedure if you want to set continuously , and if to finish, go to 7.
When plural indoor units are connected to a remote control, press
the AIRCON NO. button, which allows you to go back to the
indoor unit selection screen. (example "I/U 000
(RESET) button, you return to the previous screen.
-
88
-
P JA 012D 73 0
,
Function No.
Fixing button
7
Finishing button
2
Starting button
Previous screen button
The lowest number of
button.
", you can set the same setting with
(SET) button.
button.
Function No.
Function
If "02 FAN SPEED SET" is
Setting
button.
")
www.ampair.co.uk | sales@ampair.co.uk
'15 • PAC-T-236
Advertisement
Table of Contents
