- Please follow the directions, and read the guidelines carefully before use. Please keep the owner’s guide for future reference. - Some functions of the BT 100 NC may not be available when it is paired with certain devices. - The specifications are subject to change without prior notice for quality improvement.
4) Do not store the device in places with a temperature higher than 113 ℉/ 45 ℃. 5) This product is sweat and water resistant. Do not get the product completely wet. If the device becomes wet, turn the power off, dry the device with a dry towel and contact Phiaton Customer Service for an inspection.
The device may not be charged upon purchase and must first be charged before use. 1) Open the USB cover on BT 100 NC and connect the provided USB charging cable. 2) Connect the provided USB charging cable with a computer (laptop) or you may also use a separately purchased USB adaptor (rating: 5V/over 500mA) to begin charging.
※ Pairing mode will start once the power is turned on for the first time after purchase. ※ When the BT 100 NC is not in use, ensure the NC function is switched OFF. If left in the ON position, this will cause the battery to run out. If the NC Function is switched ON even after the power is turned off, it is displayed in blue lights to...
- When having entered ‘Connection Waiting Mode’ during connection - Press the CALL/POWER Button or the PLAY Button on the earphone to connect. - The BT 100 NC will also be connected if you select ‘BT 100 NC’ from the device search list within your ‘Bluetooth Device’.
- Turn on the Bluetooth feature within the two 'Bluetooth Devices' you want to connect with BT 100 NC. - Refer to ‘6. PAIRING WITH A ‘BLUETOOTH DEVICE’ to pair the first device with the BT 100 NC. - Press and hold the PLAY Button again for 2.5 seconds to enter ‘Pairing Mode’.
- If you press the (+) Button for 2.5 seconds again, then Auto Mode will turn off and switch to Manual Mode. ※ Upon Multipoint Connection, the features operated within BT 100 NC usually operate within the second paired device. (When using the first paired device, it is possible to operate the device from BT 100 NC.)
: Brief Hold : Press and Hold ※ Music can be listened to through BT 100 NC by directly operating your ‘Bluetooth Device’. ※ When the battery is completely drained, you can connect the provided audio cable to continue listening.
13. USING THE CALL FUNCTION 1) Accepting a Call - When the incoming call tone is heard through the earphones or the incoming call vibration is ringing, Play Button press the CALL/POWER Button. (Adjusting Call Volume: to control the call volume, Press the (+)/(-) Button.) Call/Bluetooth Power Button...
※ The above times may differ depending on the environment in which it is used. 15. OUT OF COMMUNICATION RANGE 1) The BT 100 NC vibrates when you are out of communication range (about 10 m/33 ft.) from the ‘Bluetooth Device’.
“POWER ON, Pairing Mode activated” 17. CONNECTING AND USING THE AUDIO CABLE 1) BT 100 NC can also be used with the audio cable connected as shown in the figure. ※ When connected to a device with the provided audio cable, the Bluetooth remote features are disabled and you must use the device you are connected to answer calls and play music.
- Mic. for Noise Cancelling 19. PRODUCT SYMPTOMS AND TROUBLESHOOTING 1) The power does not turn on: - Charge the device. If the power does not turn on even after charging, contact Phiaton Customer Service. 2) The device does not charge: - Check whether the USB charging cable has been properly connected with the device.
11) The device is paired with PC/Laptop but does not work: - PC/Laptop is equipped with various Bluetooth drivers depending on the manufacturer and it is possible it does not support BT 100 NC. - Please contact to PC/Laptop manufacturer to download the latest software driver or for further assistance in connecting to a ‘Bluetooth Device’.
RF energy that are deemed to comply without testing of specific absorption ratio (SAR). 22. CE COMPLIANCE INFORMATION Phiaton, hereby declares that this BT 100 NC is in compliance with the essential requirements and other relevant provisions of directive 1999/5/EC.
Page 16
2) Activating/Deactivating the LED Indicator - BT 100 NC is equipped with an indicator that shows operating features to provide information on operating status. - Press the (-) Button and (+) Button simultaneously for about 2.5 seconds to deactivate the indicator (LED) that shows operating status.