Related Manuals for Kärcher HDS 5.6/35 De Cage
Summary of Contents for Kärcher HDS 5.6/35 De Cage
- Page 1 OPERATOR MANUAL 98034310-1 MODEL # ORDER # HDS 5.6/35 De Cage 1.110-622.0 HDS 5.6/35 De Cage 1.110-623.0 To locate your local Kärcher Commercial Pressure Washer Dealer nearest you visit www.karchercommercial.us 05/10/17 9.803-436.0-B...
- Page 2 • Pump Volume at Pump Head: 5.6 GPM • Pump Pressure at Pump Head: 3500 PSI • Pump Pressure at Pump Head: 3500 PSI • Burner Type: Karcher KT • Burner Type: Karcher KT • Burner BTU's: 523,000 • Burner BTU's: 523,000 •...
-
Page 3: Table Of Contents
CONTENTS Introduction & Important Safety Information Component Identifi cation Assembly Instruction Operating Instructions Detergents & Cleaning Tips Shut Down & Clean-Up Storage Maintenance Troubleshooting 13-16 Preventative Maintenance & Oil Change Chart Model Number ______________________________ Serial Number ______________________________ Date of Purchase ____________________________ The model and serial numbers will be found on a decal attached to the pressure washer. -
Page 4: Introduction & Important Safety Information
INTRODUCTION & IMPORTANT SAFETY INFORMATION WARNING: This machine exceeds Thank you for purchasing this Pressure Washer. WARNING 85 db appropriate ear protection We reserve the right to make changes at any time must be worn. without incurring any obligation. Owner/User Responsibility: The owner and/or user must have an understanding of the manufacturer’s operating instructions and warnings EAR PROTECTION... -
Page 5: Important Safety Information
IMPORTANT SAFETY INFORMATION In an overfi lling situation, additional precautions are WARNING: High pressure devel- WARNING necessary to ensure that the situation is handled oped by these machines will in a safe manner. cause personal injury or equip- WARNING: Risk of injury. Disconnect battery ment damage. - Page 6 IMPORTANT SAFETY INFORMATION extensive periods of time as this may cause dam- age to the pump. 23. Protect discharge hose from vehicle traffi c and sharp objects. Inspect condition of high pressure hose before using or bodily injury may result. 24.
-
Page 7: Component Identifi Cation
COMPONENT IDENTIFICATION Inlet Connection Water Supply Hose Flue Adapter (not included) Optional 7-10049 Insulation Gasket Optional 7-01471 NOTE: Burner air adjustment must be tested after installation. Rupture Disk Diesel Adjustable Fuel Tank Thermostat High Pressure Burner Hose Switch Unloader Valve 98034360-2 Detergent Metering... -
Page 8: Assembly Instruction
ASSEMBLY INSTRUCTIONS Safety Pressure Dipstick Latch Nozzle Wand Spray High Pressure Hose 98034360-5 98034360-4 98034360-3 STEP 1: Attach the high pressure STEP 2: Pull the spring-loaded col- STEP 3: Remove shipping cap, if hose to the spray gun using tefl on lar of the wand coupler back to insert equipped, and install oil dipstick. -
Page 9: Operating Instructions
OPERATING INSTRUCTIONS Oil Dipstick Oil Cap Filter Fuel Tank 98034360-9 98034360-10 STEP 1: Read operator's manual before operating machine. Check engine STEP 2: Fill engine/burner fuel tank oil level. Oil level should be level with the bottom of the oil fi ller neck. (Refer with No. -
Page 10: Detergents & Cleaning Tips
DETERGENTS & GENERAL CLEANING TECHNIQUES WARNING: Some detergents THERMAL PUMP PROTECTION WARNING may be harmful if inhaled or in- If you run the engine on your pressure washer for 3-5 gested, causing severe nausea, minutes without pressing the trigger on the spray gun, fainting or poisoning. -
Page 11: Shut Down & Clean-Up
SHUTTING DOWN AND CLEAN-UP Burner Switch On-Off Key Switch 98034360-20 98034360-22 98034360-21 STEP 2: Turn burner switch off and STEP 1: Remove detergent suction STEP 3: Turn off water supply. tube from container and insert into continue spraying, allowing water to one gallon of fresh water. -
Page 12: Maintenance
MAINTENANCE Winterizing Procedure: PREVENTATIVE MAINTENANCE Damage due to freezing is not covered by warranty. Ad- 1. Check to see that water pump is properly lubri- here to the following cold weather procedures whenever cated. the washer must be stored or operated outdoors under 2. -
Page 13: Troubleshooting
TROUBLESHOOTING PROBLEM POSSIBLE CAUSE SOLUTION LOW OPERATING Faulty pressure gauge Install new gauge. PRESSURE Insuffi cient water supply Use larger supply hose; clean fi lter at water inlet. Old, worn or incorrect spray nozzle Match nozzle number to machine and/or replace with new nozzle. - Page 14 TROUBLESHOOTING PROBLEM POSSIBLE CAUSE SOLUTION BURNER WILL Flex coupling slipping on fuel Replace if needed. NOT LIGHT pump shaft or burner motor shaft (continued from On-Off switch defective Check for electrical current reaching burner previous page) assembly with burner switch on. Heavy sooting on coil and burner Clean as required.
- Page 15 TROUBLESHOOTING PROBLEM POSSIBLE CAUSE SOLUTION LOW WATER Improper fuel or water in fuel Replace with clean and proper fuel. TEMPERATURE Low fuel pressure Increase fuel pressure. Weak fuel pump Check fuel pump pressure. Replace pump if needed. Fuel fi lter partially clogged Replace as needed.
- Page 16 TROUBLESHOOTING PROBLEM POSSIBLE CAUSE SOLUTION OIL DRIPPING Oil seal worn Check and replace if necessary. EXCESSIVE Irregular functioning of the valves Check and replace if necessary. VIBRATION IN DELIVERY LINE DETERGENT Air leak Tighten all clamps. Check detergent lines for NOT DRAWING holes.
-
Page 17: Preventative Maintenance & Oil Change Chart
PREVENTATIVE MAINTENANCE This pressure washer was produced with the best available materials and quality craftsmanship. However, you as the owner have certain responsibilities for the correct care of the equipment. Attention to regular preventa- tive maintenance procedures will assist in preserving the performance of your equipment. Contact your dealer for maintenance. - Page 18 Form #9.803-436.0 • Printed in U.S.A.
Need help?
Do you have a question about the HDS 5.6/35 De Cage and is the answer not in the manual?
Questions and answers