Download
Share
Print this page
Lifetime 60066 Owner's Manual
  1. Manuals
  2. Brands
  3. Lifetime Manuals
  4. Outdoor Storage
  5. 60066
  6. Owner's manual

Lifetime 60066 Owner's Manual

Hide thumbs

Advertisement

Quick Links

Download this manual
OUTDOOR STORAGE
MODEL N° 60066
OWNER'S MANUAL
Keep this Identification Number in case you must contact our Customer Service Department.

Advertisement

loading
Need help?

Need help?

Do you have a question about the 60066 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Lifetime 60066

Summary of Contents for Lifetime 60066

  • Page 1 OUTDOOR STORAGE MODEL N° 60066 OWNER’S MANUAL Keep this Identification Number in case you must contact our Customer Service Department.

  • Page 2: Safety Instructions

    REGISTER YOUR LIFETIME PRODUCT TODAY! There are benefi ts to registering your Lifetime product. With our new online product registration form, it’s fast and easy! Register with us at www.lifetime.com and enjoy these great benefi ts: LIFETIME’S PROMISE TO YOU: Maintaining your privacy is our long-standing policy at Lifetime.

  • Page 3: Before Beginning Assembly

    BEFORE BEGINNING ASSEMBLY *Two adults required to *Two adults required to complete complete assembly* assembly* (+ one adult suggested as an instruction reader) Only adults should set up the product. Do not allow children in the set-up area until assembly is complete. TOOLS AND PARTS REQUIRED FOR THIS ASSEMBLY #2 Phillips 1/8"...
  • Page 4 ASSEMBLY GUIDES Refer to the following areas throughout the instructions to assist in the assembly process: This area is located at the top, left-hand TOOLS AND HARDWARE REQUIRED FOR THIS PAGE corner of the page and indicates which tools and hardware are needed to complete the assembly steps on a page.

  • Page 5: Parts & Hardware List

    PARTS & HARDWARE LIST MAIN COMPOSTER PARTS Description HARDWARE BAG Description TUMBLER ASSEMBLY HARDWARE COMPOSTER PARTS KIT BASE ASSEMBLY HARDWARE PARTS IDENTIFIER Main Composter Parts...
  • Page 6 PARTS IDENTIFIER Main Composter Parts Composter Parts Kit [BIV] WARNING...

  • Page 7: Hardware Identifier

    HARDWARE IDENTIFIER Tumbler Assembly Hardware [BIS] Base Assembly Hardware [BIT]...
  • Page 8 BASE FRAME ASSEMBLY HARDWARE REQUIRED HARDWARE BAG REQUIRED: BIT SMALL PARTS REQUIRED PARTS REQUIRED TOOLS REQUIRED Safety Glasses Phillips Screwdriver 7/16” Wrench Electric Drill w/Phillips Head...
  • Page 9 TOOLS AND HARDWARE REQUIRED FOR THIS PAGE NO HARDWARE REQUIRED FOR THIS STEP 2 ADULTS REQUIRED FOR THIS STEP BASE ASSEMBLY A-Frame Weldments (BII) Composter Leg (BIH) Repeat this step for the second Composter Leg. Outer Housing Brackets are on the outside.
  • Page 10 TOOLS AND HARDWARE REQUIRED FOR THIS PAGE #8 x 1/2” Phillips Self-Tapping Screws (BHJ) Do not overtighten Screws.
  • Page 11 TOOLS AND HARDWARE REQUIRED FOR THIS PAGE Locking Pin Spring (BIN) Locking Pin Assembly (BIX) WARNING...
  • Page 12 TOOLS AND HARDWARE REQUIRED FOR THIS PAGE 7/16” Inner Housing Brackets (BIJ) Cap Nut (ADJ) Locking Pin WARNING...

  • Page 13: Hardware Required

    TUMBLER ASSEMBLY HARDWARE REQUIRED HARDWARE BAG REQUIRED: BIS SMALL PARTS REQUIRED...

  • Page 14: Parts Required

    TUMBLER ASSEMBLY (CONT.) PARTS REQUIRED TOOLS REQUIRED Phillips Screwdriver Safety Glasses Rubber Mallet 1/8” Drill Bit (ARA) (Included) Electric Drill w/Phillips Head...
  • Page 15 TOOLS AND HARDWARE REQUIRED FOR THIS PAGE 1/2” TUMBLER ASSEMBLY Mounting End Plate (BHP) End Panel (BHM) 5/16” Steel Flat Washers (BHO) 5/16” Cap Nuts (AAN) Repeat this step for the second End Panel. Warning Sticker The extruded end of the Mounting End Plate goes toward the Tumbler.
  • Page 16 TOOLS AND HARDWARE REQUIRED FOR THIS PAGE 1/2” Flat Washer (BIO) Sleeve (BIL) 5/8” Flat Washer (BIP) over a Grease Packet (AKH) Repeat steps 2.2 - 2.3 for the second set of Washers, Bushing, Sleeve, and Hex Bolt. Tear here...
  • Page 17 TOOLS AND HARDWARE REQUIRED FOR THIS PAGE Bolt, Washer, and Sleeve Assembly Be sure to insert a Black Plastic Spacer (BIM) between the End Panel and the Inner Housing Bracket of the A-Frame as shown. Warning Sticker Bolt, Washer, and Sleeve Assembly...
  • Page 18 TOOLS AND HARDWARE REQUIRED FOR THIS PAGE...
  • Page 19 2 ADULTS REQUIRED FOR THIS STEP Orient the second End Panel to match the first to align the two ventilation holes. Have another adult hold this second Panel in place. Locking Pin Lifetime Logo Note: These two ventilation holes must be aligned.
  • Page 20 TOOLS AND HARDWARE REQUIRED FOR THIS PAGE 2 ADULTS REQUIRED FOR THIS STEP Place a Panel/Lid (BHN) It’s OK if the Screws (ADW) spin freely at this point. Do not worry about stripping the plastic. Repeat this step for the other side of the Front Panel/Lid. Divots in Front/Lid Panel Divots in End Panel Note: It’s OK if the Screws (ADW) spin freely at this point.
  • Page 21 TOOLS AND HARDWARE REQUIRED FOR THIS PAGE NO HARDWARE REQUIRED FOR THIS PAGE Ventilation Tube (BHQ) Ventilation Hole Lifetime Logo...
  • Page 22 TOOLS AND HARDWARE REQUIRED FOR THIS PAGE 2 ADULTS REQUIRED FOR THIS STEP Double Hook Straps (BJC) Panel/Lid (BHN) (Fig. 1) (Fig. 2). Fig. 1 Fig. 2...
  • Page 23 TOOLS AND HARDWARE REQUIRED FOR THIS PAGE 2.10 Pan-Head Screws (ADW) It’s OK if the Screws (ADW) spin freely at this point. Do not worry about stripping the plastic.
  • Page 24 TOOLS AND HARDWARE REQUIRED FOR THIS PAGE Repeat step 2.7 for the next Panel/Lid. 2.11 Plastic Nuts (BHK). Tighten the Screws (ADW) into the Plastic Nuts (BHK) with a screwdriver only. Do not overtighten.
  • Page 25 TOOLS AND HARDWARE REQUIRED FOR THIS PAGE Latch Assemblies (BJA) 2.12 Head Screw (ADW) It’s OK if the Screws (ADW) spin freely at this point. Do not worry about stripping the plastic. Plastic Nuts (BHK). Tighten the Screws (ADW) into the Plastic Nuts (BHK) with a screwdriver only. Do not overtighten.
  • Page 26 TOOLS AND HARDWARE REQUIRED FOR THIS PAGE Pinned Hinges (BIY) 2.13 It’s OK if the Screws (ADW) spin freely at this point. Do not worry about stripping the plastic. Plastic Nuts (BHK). Tighten the Screws (ADW) into the Plastic Nuts (BHK) with a screwdriver only. Do not overtighten.
  • Page 27 TOOLS AND HARDWARE REQUIRED FOR THIS PAGE Place two Hinge Tubes (BJB) Lid (BHN) . It’s OK if the Screws (ADW) spin freely at this point. Do not worry about stripping the plastic. place a Plastic Nut (BHK) Tighten the Screws (ADW) into the Plastic Nuts (BHK) with a screwdriver only.
  • Page 28 TOOLS AND HARDWARE REQUIRED FOR THIS PAGE Blow Hole Plug (BTK) 2.16 Repeat this step for each Panel/Lid.
  • Page 29 TOOLS AND HARDWARE REQUIRED FOR THIS PAGE NO HARDWARE REQUIRED FOR THIS STEP 2.17 Note: Remove Lid when filling and emptying Tumbler.
  • Page 30 TOOLS AND HARDWARE REQUIRED FOR THIS PAGE NO HARDWARE REQUIRED FOR THIS STEP LOCKING THE COMPOSTER Latch Hook Latch Assembly wire Repeat steps 3.1 - 3.2 for second Latch. WARNING...
  • Page 31 LIFETIME COMPOST TUMBLERS 5-YEAR LIMITED FACTORY WARRANTY THE MANUFACTURER RESERVES THE RIGHT TO MAKE SUBSTITUTIONS TO WARRANTY CLAIMS IF PARTS ARE UNAVAILABLE OR OBSOLETE. PLEASE INCLUDE YOUR DATED SALES RECEIPT AND PHOTOGRAPHS OF DAMAGED PARTS. REGISTER YOUR PRODUCT FOR QUICKER CUSTOMER SERVICE.
  • Page 32 ® ENHANCE YOUR LIFETIME PURCHASE BY ADDING ACCESSORIES OR OTHER GREAT PRODUCTS To purchase accessories or other Lifetime Products, visit us at: www.lifetime.com Or call: 1-800-424-3865...