Shure ULXD User Manual page 11

Connecting to an AMX or Crestron System
The following messages can be used to communicate with an AMX or Crestron unit across an Ethernet connection.
Message Types
The control system sends the following command messages:
Sent from the control system to the Shure device to change the value of a parameter. Used to set the parameter to a specific value. Once a
SET
command is sent, the Shure device sends back a
SET
Gets the current value of a parameter. Once a
GET
Reports the current value for a parameter. The
REPORT
command. The
Syntax
All messages sent and received are ASCII characters.
1. Each message begins with a "<" followed by a space.
2. Each message ends with a space followed by an ">"
3. Each message is terminated by a carriage return and line feed (CRLF).
The control system may need to enter the hex value, equivalent to 0x0D0A.
Please see the control system user guide for information on entering car-
riage returns.
4. If the message is a box parameter, there should be no channel number in
the string.
Command Response Table
Action
View Transmitter Name
Set Channel Name
Get Channel Name
Set Audio Level
View Audio Level
Set Transmitter Group & Channel
View Transmitter Group & Channel
Set Transmitter Frequency
View Transmitter Frequency
Set RF Tx Level
View RF Tx Level
Set RF Mute
View RF Mute
Set Audio Tx Mode
View Audio Tx Mode
Set Audio Input Line Level
View Audio Input Line Level
Set Metering Rate
View Metering Rate
Audio Meter Level
GET
string is also sent when the value of the parameter is changed on the Shure device.
REPORT
COMMAND
GET DEVICE_NAME
SET x CHAN NAME vvvvvvvv
GET x CHAN NAME
SET x AUDIO_IN_LVL vvvv
GET x AUDIO_IN_LVL
SET x GROUP_CHAN gg,cc
GET x GROUP_CHAN
SET x FREQUENCY vvvvvvvvvvv
GET x FREQUENCY
SET x RF_TX_LVL vvvvvv
GET x RF_TX_LVL
SET x RF_MUTE vvvv
1 = mute, 0 = unmute
GET x RF_MUTE
1 = mute, 0 = unmute
SET x AUDIO_TX_MODE vvvv
1 = mono, 2 = point to point, 3 = stereo
GET x AUDIO_TX_MODE
SET x AUDIO_IN_LINE_LVL vvvv
0 = off (Aux), 1 = on (Line)
GET x AUDIO_IN_LINE_LVL
SET x METER_RATE vvvvvvvvvvv
0 = off, value in milliseconds
GET x METER_RATE
REPORT x AUDIO_IN_LVL_L vvvvvvvvvvv
string with the current resultant setting.
REPORT
command is sent, the Shure device will send back a
string is sent from the Shure device to the Control system in response to a
REPORT
Example Messages
<GET 1 FREQUENCY >/0d/0a
1
Example Messages for Channel Parameters
• <REPORT 1 FREQUENCY 578000 >/0d/0a
Example Messages for Box Parameters
• <SET DEVICE_NAME Shure >/0d/0a
• <REPORT DEVICE_NAME Shure >/0d/0a
string with the current setting.
REPORT
2
RESPONSE
REPORT DEVICE_NAME vvvvvvvv
REPORT x CHAN_NAME vvvvvvvv
REPORT CHAN_NAME vvvvvvvv
REPORT x AUDIO_IN_LVL vvvv
REPORT x AUDIO_IN_LVL vvvv
REPORT x FREQUENCY vvvvvvvvvvv REPORT
x GROUP_CHAN gg,ccvvv
REPORT x GROUP_CHAN gg,cc
REPORT x FREQUENCY vvvvvvvvvvv
REPORT x GROUP_CHAN --,--vvv
REPORT x FREQUENCY vvvvvvvvvvv
REPORT x RF_TX_LVL vvvvvv
REPORT x RF_TX_LVL vvvvvv
REPORT x RF_MUTE vvvv
1 = mute, 0 = unmute
REPORT x RF_MUTE vvvv
1 = mute, 0 = unmute
REPORT x AUDIO_TX_MODE vvvv
1 = mono, 2 = point to point, 3 = stereo
REPORT x AUDIO_TX_MODE vvvv
1 = mono, 2 = point to point, 3 = stereo
REPORT x AUDIO_IN_LINE_LVL vvvv
0 = off (Aux), 1 = on (Line)
REPORT x AUDIO_IN_LINE_LVL vvvv
0 = off (Aux), 1 = on (Line)
REPORT x METER_RATE vvvvvvvvvvv
0 = off, value in milliseconds
REPORT x METER_RATE vvvvvvvvvvv
0 = off, value in milliseconds
REPORT x AUDIO_IN_LVL_L vvvvvvvvvvv
REPORT x AUDIO_IN_LVL_R vvvvvvvvvvv
or
SET GET
3
13