Shure ULXD User Manual page 10

Home Screen Display Options
Receiver
Edit the following parameters in the
: Edits the receiver's channel name (transfers to the transmitter
EDIT NAME
during a sync).
: Changes the information displayed on the LCD home screen:
HOME INFO
: Use parameter to adjust the brightness of the LCD
DISPLAY BRIGHTNESS
panel, meter LEDs and front panel icons and
the contrast of the LCD panel.
Transmitter
Home Screen: Press the ▲▼ arrows at the home menu to display one of the
following screens:
Locking Controls and Settings
Use the feature to prevent accidental or unauthor-
LOCK
ized changes to the hardware. Attempting to access a
locked feature will display the following message:
Receiver
>
UTILITIES LOCK
: All menu paths are inaccessible. To unlock, press the
MENU
the control wheel to select
UNLOCKED
: Gain adjustment is locked
GAIN
: Power switch is disabled
POWER
: Cannot perform a Scan and Sync
SCN/SYC
Transmitter
>
UTILITY LOCK
: All menu paths are inaccessible. To unlock, press the
MENU
> >
UTILITY LOCK UNLOCKED
: Power switch is disabled
POWER
Quick-Lock Option: To turn on the transmitter with its power and menu navi-
gation buttons locked, press and hold the ▼ button during power-on until the
locked message is displayed.
To unlock, turn the power switch to the off position, then press and hold the ▼
button while turning the power switch to the on position.
Transmitter Presets
Use the menu to store settings on the receiver to transfer to
TX SYNC SETUP
the transmitter during a sync. Each parameter has the default value
which leaves that setting unaffected by a sync.
Feature Setting
0 dB, -12 dB
BP PAD
All, Power, Menu, None
LOCK
High, Mid, Low
RF POWER
,
BP OFFSET
0 dB to +21 dB (in 3 dB increments)
HH OFFSET
NiMH, Lithium, Alkaline
BATT
On, Off
Cust. Group
Note: When Cust. Groups is set to on, it may take up to 30 seconds to com-
plete an IR sync.
12
menu:
UTILITIES
parameter to adjust
CONTRAST
button, turn
EXIT
and press to save.
ENTER
ENTER
Encryption
ULXD features Advanced Encryption Standard (AES-256) encryption, con-
forming to the US Government National Institute of Standards and Technology
(NIST) publication FIPS-197.
1. Enable encryption on the receiver:
symbol illuminates green and the LCD displays
2. Sync the transmitter to the receiver. The encryption symbol displays on the
transmitter.
Note: Any change to the encryption status on the receiver requires an
sync to transfer the setting to the transmitter. The Encryption Mismatch
warning will display on the receiver LCD panel if they are not on the same
setting.
System Reset
Use this feature to overwrite current settings with saved or factory default
settings.
Save a System Preset
To save the current receiver setup as a new preset:
SYSTEM RESET
Restore Settings
To restore saved or factory default settings:
1. Go to
UTILITES
2. Scroll to the preset or default settings option and press
ing warning will display:
3. Press the flashing
Advanced RF
RF Mute
4 times:
Use this to turn on a transmitter without interfering
with the RF spectrum.
Press and hold the
til is displayed. To un-mute, restart the
RF MUTED
transmitter.
Custom Groups
Use this feature to create up to six groups of manually selected frequencies
that can be exported to networked receivers to simplify system setup.
To create a custom group:
,
KEEP
Note: Use Wireless Workbench or Wireless Frequency Finder to select the
best compatible frequencies. See www.shure.com for more information.
To export a custom group:
1. Go to
UTILITES
ing screen will display.
2. Press the flashing
on the network.
Antenna Bias
To turn off:
UTILITES
UTILITIES
> > .
SAVE CREATE NEW PRESET
> >
SYSTEM RESET RESTORE
button to overwrite the current settings.
ENTER
button during power-on un-
exit
>
UTILITES ADVANCED RF
> >
ADVANCED RF CUSTOM GROUPS
button to export all custom groups to all receivers
ENTER
> >
ADVANCED RF ANTENNA BIAS
> . The encryption
ENCRYPTION
.
SYNC NOW FOR ENCYPTION
>
UTILITES
.
. The follow-
ENTER
>
CUSTOM GROUPS
> . The follow-
EXPORT
.