Shure ULXD User Manual
  1. Manuals
  2. Brands
  3. Shure Manuals
  4. Microphone system
  5. ULXD
  6. User manual

Shure ULXD User Manual

Digital
Hide thumbs Also See for ULXD:
Table of Contents

Advertisement

Quick Links

See also: User Manual , Manual
ULXD Digital Wireless System
©2011 Shure Incorporated
xxxxxxx (Rev. 1)
1

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the ULXD and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Shure ULXD

Summary of Contents for Shure ULXD

  • Page 1 ULXD Digital Wireless System ©2011 Shure Incorporated xxxxxxx (Rev. 1)

  • Page 2: Important Safety Instructions

    • Do not short circuit; may cause burns or catch fire • Do not charge or use battery packs with other than specified Shure products • Dispose of battery packs properly. Check with local vendor for proper disposal of used battery packs...

  • Page 3: General Description

    Each receiver has an RJ-45 port on the back for connecting to other receivers over an Ethernet network. Networking receivers allows you to automatically set channels for all the receivers with a single group scan command. You can also control and monitor all networked receivers through the Shure Wireless Workbench PC software.

  • Page 4: Front Panel

    -6 dBFS Illuminates when the receiver is connected with • Off = No RF connection between the receiver Normal peaks other Shure devices on the network. IP Address Yellow/ -12 dBFS and transmitter must be valid to enable networked control...
  • Page 5 ② On/Off Switch ⑧ AA Battery Adapter Powers the unit on or off Handheld: rotate and store in the battery compartment to use a Shure re- chargeable battery pack ③ TA4M Input Jack Connects to a 4-Pin Mini Connector (TA4F) microphone or instrument cable Bodypack: remove to accommodate a Shure rechargeable battery pack ④...

  • Page 6: Shure Sb900 Rechargeable Battery

    ⑤ Mic. Offset a sync Displays microphone offset gain value Batteries The transmitter runs on two AA batteries or the Shure SB900 rechargeable battery. PGXD Drawings Needed: 1. Polarity 2. AA Clip storage...

  • Page 7: Setting Gain

    Setting Gain Receiver Gain Controls Adjust gain at the receiver so that the average signal levels are solid green The receiver adjusts the system audio gain from 0 to +60 dB. No transmitter and yellow with peaks that flicker the red overload LED. Attenuate the gain if gain is necessary to optimize the gain structure.

  • Page 8: Interference Detection

    Press the flashing button to ENTER save the value to the receiver. 4. Power on the ULXD transmitter. 5. Press the button on the receiver. sync 6. Align the IR windows until the receiver IR port illuminates red.

  • Page 9: Manual Frequency Selection

    2. If not, find the IP address from one of the devices on the network (such as an ULXD receiver) and see if you can ping it from the computer running WWB6. 3. From a WINDOWS/MAC command prompt, type ‘ping IPADDRESS’ of the device (e.g.
  • Page 10 Home Screen Display Options Encryption ULXD features Advanced Encryption Standard (AES-256) encryption, con- Receiver forming to the US Government National Institute of Standards and Technology (NIST) publication FIPS-197. Edit the following parameters in the menu: UTILITIES 1. Enable encryption on the receiver: >...
  • Page 11 The control system sends the following command messages: Sent from the control system to the Shure device to change the value of a parameter. Used to set the parameter to a specific value. Once a command is sent, the Shure device sends back a string with the current resultant setting.

  • Page 12: Troubleshooting

    Manager tool available in Shure’s Wireless Workbench (WWB) software. Software is available for download from http://www.shure.com/wwb. ® Perform the following steps to update the firmware for the ULXD system: 1. Download the latest firmware to WWB software: > . Click to view and download the latest versions.

  • Page 13: Tables And Diagrams

    Tables and Diagrams Frequency Range and Transmitter Output Power Band Frequency Range Power ( mW) Band Frequency Range Power ( mW) ( MHz) ( MHz) 470 to 534 1/10/20 632 to 696 1/10/20 470 to 534 1/10/20 710 to 782 1/10/20 479 to 534 1/10...

  • Page 14: Licensing Information

    Changes or modifications not expressly approved by the manufacturer could void the user’s authority to operate the equipment. The CE Declaration of Conformity can be obtained from Shure Incorporated or any of its European representatives. For contact information please visit www.

Table of Contents