Table of Contents
Advertisement
Quick Links
T W O - W A Y
A S - 6 8 5 0 v T W - F M
Once the battery is weak, the LCD remote will display a battery low voltage
icon and a "L-BAT" indication with 2 beeps to warn the user to change it.
FCC USER NOTICE (U.S.A.):
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device
may not cause harmful interference, and (2) this device must accept any interference received, including interference
that may cause undesired operation.
NOTE: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to
this equipment. Such modifications could void the user's authority to operate the equipment.
DOC: 1.00
- AS-6850vTW-FM -
L C D
T R A N S M I S S I O N
W I T H
F U L L
User Guide
It is the responsibility of the vehicle operator to ensure their vehicle
is parked in a safe and responsible manner.
1.
a) Manual transmission: When leaving the vehicle, it is the user's
responsibility to ensure that the gearshift lever is in the NEUTRAL
position and the parking brake is engaged in order to avoid accidents
upon remote starting.
b) Automatic transmission: When leaving the vehicle, it is the user's
responsibility to ensure that the gearshift lever is in "Park" in order to
avoid accidents upon remote starting.
(Note: Make sure that the automatic vehicle cannot start in "Drive".)
2. It is the user's responsibility to ensure that the remote starter is disabled
or put into valet mode before servicing.
Battery Low Voltage Warning
- November 8, 2007 -
A U T O M A T I C / M A N U A L
R E M O T E
S T A R T E R
A L A R M
S Y S T E M
WARNING
- MO -
Assembled in Canada
Advertisement
Table of Contents
Related Manuals for Autostart AS-6850VTW-FM
Summary of Contents for Autostart AS-6850VTW-FM
- Page 1 (Note: Make sure that the automatic vehicle cannot start in "Drive".) 2. It is the user's responsibility to ensure that the remote starter is disabled or put into valet mode before servicing. Battery Low Voltage Warning Once the battery is weak, the LCD remote will display a battery low voltage icon and a “L-BAT”...
-
Page 2: Table Of Contents
When leaving the vehicle you must ensure that the windshield wiper and headlight switches are cause them to remain even after remote starter shut down, resulting in a dead battery. P. 2 Table of Contents Secure Lock ... 14 Remote Trunk Release... -
Page 3: Using The Transmitter
Using the Transmitter Your remote starter is equipped with a 6-button, multi-channel, 2-way remote control. It can operate two independent vehicles equipped with identical remote starters (see Multi-car operation section on page 17). LCD Remote Functions The transmitter offers several command-confirmation and timer features. This section explains some of the key functions available. - Page 4 Backlight: Press and hold the button (for more than 3 seconds and less than 5 seconds), to turn the Backlight for 3 seconds. If the backlight will stay until the press the button quickly (for less than 1 second); the backlight will turn on until the operation ends.
- Page 5 Side Button Programming Language Menu Language Temperature Menu Temperature Clock Menu Clock hours Clock minutes Confirmation Mode Menu Confirmation Mode Toggle BZVIB Toggle BLITE Backlight Color Menu Backlight SECURE Menu Toggle lock remote Time Start Menu Time start hours Time start minutes Toggle time start VALET Menu Valet Mode options...
- Page 6 Alarm Clock Menu Alarm hours Alarm minutes Toggle alarm Parking Countdown This version of the countdown feature is particularly useful for keeping track of parking meter time: The user may quickly set up the countdown using the 5 min. before the Parking countdown reaches 0. Alarm Clock The LCD remote control has a built-in alarm clock, which can be set up using the .
-
Page 7: Remote Starting Your Vehicle
Button Operation: Button Lock button Unlock button Trunk button Start button Engine running Engine stop Button Unlock+Start buttons Lock+Unlock buttons Trunk+Lock buttons car operation) Trunk+Unlock buttons car operation) Trunk+Start buttons car operation) L --01 → Lock button L --01 → Unlock button L --01 →... -
Page 8: Setting Your Vehicle Into Ready Mode
1. Turn the ignition key to the position while the engine is running. This would cause the starter motor to re-engage.) 2. Press the brake pedal to disengage the remote starter unit. You are now ready to drive off. P. 8... -
Page 9: Arming The Starter Kill
This feature allows you to let the remote starter take over control of the vehicle (i.e. no Key in the Ignition Switch) while the engine is running. -
Page 10: Valet Modes
Combo Valet Mode, both the remote starter functions and the alarm functions are disabled. When your vehicle is in Valet Start Mode, only the remote starter functions are disabled. When your vehicle is in Valet Alarm Mode, only the alarm functions are disabled. -
Page 11: Valet Start Mode
2- Getting into Combo Valet Mode using combined buttons on the transmitter: • Hold the buttons simultaneously for 3 seconds. • The parking lights will flash 3 times and the LED on the antenna will remain • The icon will appear on your LCD remote. 2- Getting out of Valet Mode using combined buttons on the transmitter: •... -
Page 12: Valet Alarm Mode
• The parking lights will flash 2 times and the LED on the antenna will turn • The icon will disappear on your LCD remote. Valet Alarm Mode This feature will allow you to put your system into Valet Alarm Mode by using the transmitter. Getting into Valet Alarm Mode •... -
Page 13: How To Access Cold Weather Mode
Remote Door Locks If your remote starter was installed with the remote door locks option, you will have the convenience of remote keyless entry. See section “Arming the Starter Kill”, on page 9, for further instructions on remote door locking and unlocking. -
Page 14: Ignition-Controlled Door Locks
With this added security feature, the system will prevent your vehicle from starting with the ignition key when armed. If your remote starter was installed with the starter kill option, one will not be able to start your vehicle with the key unless the system has been unlocked and disarmed first, or put into valet mode. -
Page 15: How To Access Safe Start Mode
Valet Mode Using the Valet Switch ( When your vehicle is in Valet Mode, the remote starter functions are disabled. If the vehicle needs to be serviced, or if you park it indoors, the Valet Mode will prevent the engine from being remote started accidentally. -
Page 16: How To Access Home Valet Mode
Engine Run Time If you have a gas engine, your remote starter can be programmed to run the engine for 3, 15, or 25 minutes (15 minutes by default). If you have a diesel engine, the remote starter can be programmed to run the engine for 8, 20, or 30 minutes (20 minutes default). -
Page 17: How To Access Run Time Status (Indications Purposes Only)
LOCK UNLOCK Multi-car Operation This option allows the owner of two vehicles, both equipped with the same remote starter model, to control both systems independently with a single remote control. To control the second vehicle: Press Press... -
Page 18: Lcd Transmitter Operation And Confirmation (Second Car Control)
LCD Transmitter Operation and Confirmation (Second Car Control) Basic Operations Function Lock Unlock Start Stop Trunk Start/Stop While in Safe Start Mode Function Button press Start on Safe Start Mode Stop on Safe Start Mode Multi-Level Features (default state) The multi-level features allow you to access different features of your vehicle or of a second car by pressing the button once, twice or three times. -
Page 19: Accessing The Multi-Level Features And Other Transmitter Functions
Accessing the Multi-Level Features and Other Transmitter Functions • To access a Level 1 feature, press and release the L-01 will be displayed. This display means that you are now in Level 1. Simply press the corresponding button to access the desired feature. •... -
Page 20: Troubleshooting Transmitting Range
Troubleshooting Transmitting Range Many factors may affect the operating range of the transmitter. Some of these are: • The condition of the battery in the transmitter. • The operating environment (for example: downtown radio-frequency noise, airports, cellular phone towers…) • Metal: any type of metal will affect operating range. This includes the vehicle itself. •... -
Page 21: Diagnostics - Parking Light Flash Table
Diagnostics – Parking Light Flash Table Flashes • Doors locked, alarm and starter kill armed • Run time has expired • TRUNK • Remote start attempt cancelled by remote • Doors unlocked, starter kill disarmed • Exiting ignition valet • Power ON to OFF(automatic transmission) 2 slow flashes then •... -
Page 22: Limited Lifetime Warranty
In all cases, the consumer must return the remote starter module to the point of purchase, and must provide a copy of the proof of purchase to said retailer. A remote starter module will be returned to the retailer for the consumer to claim within a 4 (four)-week period.