Casio BGC-110B Service Manual And Parts List page 6

OPERATION CHART : MODULE QW-2177
• Press to change from mode to mode.
C
• Pressing in any mode illuminates the display for about 3 seconds.
L
• If you do not perform any operation for a few minutes while a setting screen (with flashing digits) is on the display, the watch automatically exits the setting screen.
• If you do not perform any operation for a few minutes in Day Counter Mode and Telememo Mode, the watch automatically reverts to the normal timekeeping screen.
• When making settings (except Easy Timer setting), note that you can scroll only forward, you cannot scroll back. This means that if you go past the setting you want, you must scroll
through all of the available settings again until the one you want reappears.
Timekeeping Mode
Press
TIMEKEEPING MODE
• Press to toggle the display between the day of the week and month, as shown
B
below.
Day of week Day
Hour : Minutes
DST on indicator
• Press to toggle the display between the 12-hour and 24-hour timekeeping.
D
• With 12-hour timekeeping, times between midnight and noon are indicated by A
(am), while times between noon and midnight are indicated by P (pm).
• The A and P indicators do not appear when you are using 24-hour timekeeping.
To set the time and date
1. While in the Timekeeping Mode, hold down
display, indicating the setting screen.
2. Press to move the flashing in the sequence shown below.
C
Seconds
Day Month
3. While the seconds setting is selected (flashing), press
press while the seconds setting is in the range of 30 to 59, the seconds are
D
reset to 00 and 1 is added to the minutes. If the seconds setting is in the range of
00 to 29, the minutes count is unchanged.
• While the DST setting is selected (DST on indicator is flashing), press
it on (ON) and off (OF).
4. While any other setting is selected (flashing), press
changes the setting at high speed.
D
5. After you make the settings you want, press
• The day of the week is automatically set in accordance with the date.
• The date can be set within the range of January 1, 2000 to December 31, 2039.
• The watch's built-in full automatic calendar automatically makes allowances for dif-
ferent month lengths and leap years. Once you set the date, there should be no
reason to change it except after the replacement of the watch's battery.
Daylight Saving Time (DST), which is also sometimes called "summer time" ad-
vances the time for one hour, as is the custom in some areas during the summer.
Remember that not all countries or even local areas use Daylight Saving Time.
ABOUT THE BACKLIGHT
• Press to illuminate the display for about three seconds.
L
• The backlight of this watch employs an electro-luminescent (EL) light, which loses
its illuminating power after very long term use.
• Frequent use of the backlight shortens the battery life.
• The watch emits an audible sound whenever the display is illuminated. This does
not indicate malfunction of the watch.
• The illumination provided by the backlight may be hard to see when viewed under
direct sunlight.
• The backlight automatically turns off whenever an alarm sounds.
Day Counter Mode
.
C
Month
Press .
B
Seconds
until the seconds digits flash on the
A
DST Hour
Year Minutes
D to reset it to 00. If you
D to toggle
to increase it. Holding down
D
to exit the setting screen.
A
GENERAL GUIDE
Telememo Mode
The Day Counter Mode lets you count the number of days from the Timekeeping
Mode's current date to a specific target date.
There are ten day counters, each identified by a counter number. You can assign text
titles up to eight characters long to each of the 10 Day Counters. Whenever the date
specified by any one of the day counters matches the date of the Timekeeping Mode
(regardless of the day counter's year setting), the DAYS indicator flashes on the
Timekeeping Mode. In the Day Counter Mode, the DAYS indicator flashes on the
screen of the particular day counter whose date matches the date of the Timekeep-
ing Mode.
The initial default date for all Day Counters is January 1, 2001.
The page number on the display when you exit the Day Counter Mode appears first
the next time you enter the Day Counter Mode.
Page number
Mode indicator
Text
DAYS indicator
Recalling Day Counter Data
In the Day Counter Mode, press
To set the target date
1. In the Day Counter Mode, press
you want to set.
2. Hold down until the flashing cursor appears in the text area. This indicates the
A
input screen.
3. Press to move the flashing in the sequence shown below.
C
• Holding down
C
4. While the cursor is in the text area, use
current cursor position. Characters scroll in the sequence shown below. Holding
down C scrolls at high speed.
Press
(Space)
5. While the cursor is in the date area, press
cursor position. Holding down
• Press and
B
D
characters in the text area is cleared and today's date is set as the target date. You
can then make any changes in the date you want.
6. After you make the settings you want, press
• The date can be set within the range of January 1, 1940 to December 31, 2039.
• The text area display can show only three characters at a time. Longer text scrolls
continuously from right to left. The symbol " " indicates that the character to the left
is the last, and the character to the right is first.
- 5 -
Easy Timer Mode
DAY COUNTER MODE
Year
Alternate at the
1-second interval.
Numbers of days
(+) or (–) to scroll through the day counters.
D B
(+) or (–) to display the number of the counter
D B
to move the flashing at high speed.
Press .
C
1st digit 8th digit
Day Month
to scroll through characters at the
C
.
C
A to Z 0 to 9 . (Period)
to scroll through digits at the current
C
scrolls at high speed.
C
at the same time. The message " CLR" appears in the display. The
to exit the input screen.
A
Alarm Mode
Target date
Month Day
Year
- (Hyphen)