Sony HBD-E780W Service Manual page 86

HBD-E780W/E980W/E985W
Ver. 1.2
Pin No. Pin Name
AF11,
RDQ30, RDQ20
AF12
AF13,
DVCC15_IO_1
AF14
AF15,
RA9, RA2
AF16
AF17 DGND
AF18,
RDQ1, RDQ3
AF19
AF20 DVCC15_IO_1
AF21,
RDQ15, RDQ6
AF22
AF24 TN_MEMPLL
AF25 RDQ16_B
AF26 DGND
AF27 RDQS3_B
AF28 RDQS3_B_
AG1,
NFD3, NFD0
AG2
AG3 NFCLE
AG4 NFWEN
AG5 SFDI
AG7,
RDQ16, RDQ19
AG8
AG9 RDQS2
AG10 RDQS3_
AG11 RDQ29
AG13 RCLK1
AG14 RBA0
AG16 RCKE
AG17 RDQ0
AG19 RDQ9
AG20 RDQS0
AG21 RDQS1_
AG22 RDQ7
AG24 RCLK0
AG25 RDQ17_B
AG26 DVCC15_IO_1
AG27 RDQS2_B
AG28 RDQS2_B_
AH1 NFD1
AH2 NFCEN
AH4 SFDO
AH5 SFCS
AH7,
RDQ17, RDQ18
AH8
AH9 RDQS2_
AH10 RDQS3
AH11 RDQ28
AH13 RCLK1_
AH14 RA3
AH16,
RA8, RA10
AH17
AH19 RDQ8
AH20 RDQS0_
AH21 RDQS1
AH22 RDQ13
AH24 RCLK0_
AH25 to RDQ18_B, RDQ19_B,
AH28 RDQ26_B, RDQ27_B
82
I/O
I/O Two-way data bus with the SD-RAM
- Power supply terminal (+1.5V)
O Address signal output to the SD-RAM
- Ground terminal
I/O Two-way data bus with the SD-RAM
- Power supply terminal (+1.5V)
I/O Two-way data bus with the SD-RAM
- Test terminal
I/O Two-way data bus with the SD-RAM
- Ground terminal
O Data strobe signal (negative) output to the SD-RAM
O Data strobe signal (positive) output to the SD-RAM
I/O Two-way data bus with the NAND fl ash
O Command latch enable signal output to the NAND fl ash
O Write enable signal output to the NAND fl ash
LPF selection signal output to the video amplifi er
O
(US, Canadian, Australian, Singapore, Taiwan and Thai models)
I/O Two-way data bus with the SD-RAM
O Data strobe signal (positive) output to the SD-RAM
O Data strobe signal (negative) output to the SD-RAM
I/O Two-way data bus with the SD-RAM
O Clock signal (positive) output to the SD-RAM
O Bank address signal output to the SD-RAM
O Clock enable signal output to the SD-RAM
I/O Two-way data bus with the SD-RAM
I/O Two-way data bus with the SD-RAM
O Data strobe signal (positive) output to the SD-RAM
O Data strobe signal (negative) output to the SD-RAM
I/O Two-way data bus with the SD-RAM
O Clock signal (positive) output to the SD-RAM
I/O Two-way data bus with the SD-RAM
- Power supply terminal (+1.5V)
O Data strobe signal (negative) output to the SD-RAM
O Data strobe signal (positive) output to the SD-RAM
I/O Two-way data bus with the NAND fl ash
O Chip enable signal output to the NAND fl ash
O Serial data output terminal
USB VBUS on/off control signal output terminal wireless LAN card
O
(E780W/E980W only)
I/O Two-way data bus with the SD-RAM
O Data strobe signal (negative) output to the SD-RAM
O Data strobe signal (positive) output to the SD-RAM
I/O Two-way data bus with the SD-RAM
O Clock signal (negative) output to the SD-RAM
O Address signal output to the SD-RAM
O Address signal output to the SD-RAM
I/O Two-way data bus with the SD-RAM
O Data strobe signal (negative) output to the SD-RAM
O Data strobe signal (positive) output to the SD-RAM
I/O Two-way data bus with the SD-RAM
O Clock signal (negative) output to the SD-RAM
I/O Two-way data bus with the SD-RAM
Description
"L": 13.5 MHz LPF, "H": 30 MHz LPF
Not used
"H": VBUS on