Page 1
Prestigio P370MW User’s Manual Trademarks HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licens- ing LLC. All other brand and product names are trademarks or registered trademarks of their respective companies. Note The information in this manual is subject to change without notice.
8. During the LCD panel lifespan it is normal for a few pixels to become defective. Non-active pixels may appear on the screen as fixed points of red, blue or green. Refer pixel policy questions to your dealer for further clarification on acceptable loss. PRESTIGIO P370MW...
4.4 Connecting a VCR, Camcorder, or Game Console ......................... 28 Using the S-Video Connection ............................... 28 Using the Composite Connections ..............................28 Using the SCART Connection ................................29 4.5 Connecting a Computer ..............................30 Using the DVI Connection ................................30 PRESTIGIO P370MW...
* Chapter 6, Adjusting LCD TV Settings, describes how to adjust the settings using the On Screen Display (OSD). * Chapter 7, Troubleshooting, gives solutions to common problems. * Appendix A and B, Specifications, provides brief specifications of the LCD TV. PRESTIGIO P370MW...
3. Install the two AAA batteries into the battery compartment as depicted by the diagram in the interior of the battery compartment showing the positive (+) and negative (–) ends of the batteries. 4. Place the battery door back into place and make sure it clicks into position. PRESTIGIO P370MW...
2. Remove the screws connecting the stand to the LCD TV. NOTE: The speaker do not have to be removed to remove the stand. 3. Pull outwards on the base to detach the stand from the LCD TV frame. PRESTIGIO P370MW...
1. Prepare an F-type coaxial cable. 2. Connect one end of the corresponding coaxial cable to the TV input connector. Connect the other end to an antenna or cable TV connector on the wall. PRESTIGIO P370MW...
Plug the female end of the power cord to the power connector on the rear of the LCD TV and plug the male end to an electrical outlet. CAUTION: * When unplugging the power cord, disconnect from the electrical outlet first, then from the system. * When unplugging the connector, always hold the plug head. Never pull on the cord. PRESTIGIO P370MW...
To turn the TV off, press the POWER button located on the right side panel of the TV or the power button on the remote control. The power indicator on front of the LCD TV lights orange to indicate that the TV is in off (standby) mode. PRESTIGIO P370MW...
* HDTV resolution (480i, 480p, 576i, 576p, 720p, 1080i) through component, DVI and HDMI™ 2.2 Front Panel Indicators Ref. Component Description See Also Remote Sensor Receives signal input from the remote control. Power Indicator Green: On Section 1.4 Orange: Standby Off: Main power off (see the Rear Panel Inputs/Outputs) PRESTIGIO P370MW...
Line In Connector Connects to the audio out connector of a computer. Section 4.5 Main Power Switch Turns the main power on and off. Section 1.4 Power Connector Connects to an A/C outlet for powering the display. Section 1.3 PRESTIGIO P370MW...
Connects to video and audio equipment such as VCRs, DVD players, digital set top boxes, computers, and gaming systems that utilize SCART video. AV2 In Connectors Connects to video equipment such as DVD players and Chapter 4 digital set top boxes that utilize component video. PRESTIGIO P370MW...
Component Description See Also Headphone Connector Connects to a set of headphone. AV1 In Connectors Connects to a variety of video equipment that supports Chapter 4 composite and S-Video connections such as DVD players, VCR’s and game consoles. PRESTIGIO P370MW...
Opens or closes the OSD menu. Chapter 6 SOURCE Button Switches to another input source (VGA, DVI, AV1, AV2, Chapter 5 SCART1, SCART2, SCART3, TV, and HDMI). OSD active: activates your selection. Power Button Turns the TV ON and OFF (standby). Section 1.4 PRESTIGIO P370MW...
DTV broadcasts. SOUND Toggle audio mode for Section 3.2 NICAM/A2 TV broadcast. SLEEP Sets the sleep timer. Section 5.5 FREEZE Freezes the display image. Section 5.2 MUTE Toggles mute on and off. Section 3.2 PRESTIGIO P370MW...
Page 16
MEMORY Save the currently viewed Section 3.3 channel as a favourite channel. \/ /\ < > Navigates the OSD menu. Chapter 6 In PIP mode is used to navigate in the sub-window. PRESTIGIO P370MW...
Page 17
See Also Number Enter a TV channel number. Section 3.2 (0, 1 Enters a password when Section 5.4 to 9) child lock is in use. Returns to the previously Section 3.2 viewed channel. Selects a 3-digit channel. Section 3.2 PRESTIGIO P370MW...
1. Press the MENU button to open the OSD main menu. 2. Press the ( button three times to select the option icon and press ENTER to open the Set Up menu. 3. Press ENTER to allow your TV to select your country. PRESTIGIO P370MW...
* For A2 TV broadcast : Stereo (Stereo/Mono) Bilingual (CH A / CH B / CH AB) Monaural (Mono) Your LCD TV can automatically detect which broadcast service it has. Just press SOUND to select the sound mode you want. PRESTIGIO P370MW...
CH+ or CH? button. You can erase a channel range using the following instructions: 1. Press the MENU button to open the OSD main menu. 2. Press the > button three times to select the option icon and press ENTER to open the Set Up menu. PRESTIGIO P370MW...
Component video takes the advancement from composite (1-signal) to S-Video (2-signals) a step further. It carries the Y, R-Y, and B-Y signals separately. Use component video to take advantage of the superior picture provided by HDTV and progressive scan DVD sources. PRESTIGIO P370MW...
3. To watch a DVD, turn on your LCD TV, press the SOURCE button to open the Main Source menu. Press ( to scroll through the source list and select HDMI as the input source. Press ENTER to confirm HDMI as your selection. 4. Turn on the DVD player. NOTE: For more information, see the instructions supplied with your DVD player. PRESTIGIO P370MW...
3. Connect the R (red) and L (white) audio cable ends to the L-Audio-R connectors at the AV1 location on the LCD TV. Connect the other ends to the corresponding left and right audio connectors on the DVD player. PRESTIGIO P370MW...
4. To watch a DVD, turn on your LCD TV, press the SOURCE button to open the Main Source menu, press ( to scroll through the source list and select AV 1 as the input source. Press ENTER to confirm AV1 as your selection. PRESTIGIO P370MW...
SCART 1, SCART 2, or SCART 3 as the input source. Press ENTER to confirm SCART 1, SCART 2, or SCART 3 as your selection. 4. Turn on the DVD player. NOTE: For more information, see the instructions supplied with your DVD player. PRESTIGIO P370MW...
3. Connect one end of the Pb cable (blue) to the Pb connector (blue) at the AV2 location on the LCD TV. Connect the other end to the corresponding Pb connector (blue) on the HDTV Set-top box. 4. Connect one end of the Pr cable (red) to the Pr connector (red) at the AV2 location on the LCD TV. Connect the other PRESTIGIO P370MW...
3. To watch HDTV, turn on your LCD TV, press the SOURCE button to open the Main Source menu. Press ( to scroll through the source list and select SCART 1, SCART 2, or SCART 3 as the input source. Press ENTER to confirm SCART 1, SCART 2, or SCART 3 as your selection. PRESTIGIO P370MW...
3. Connect the R (red) and L (white) audio cable ends to the L-Audio-R connectors at the AV1 location on the LCD TV. Connect the other ends to the corresponding left and right audio connectors on the VCR / camcorder / game console. PRESTIGIO P370MW...
1. Prepare the SCART cable. 2. Connect one end of the SCART cable to the SCART connector at the SCART1/SCART2/SCART3 locations on the LCD TV. Connect the other end to the corresponding SCART connector of the VCR / camcorder / game console. PRESTIGIO P370MW...
4. To use the computer, turn on your LCD TV, press the SOURCE button to open the Main Source menu, press ( to scroll through the source list and select DVI as the input source. Press ENTER to confirm DVI as your selection. 5. Turn on the computer. PRESTIGIO P370MW...
4. To use the computer, turn on your LCD TV, press the SOURCE button to open the Main Source menu, press ( to scroll through the source list and select VGA as the input source. Press ENTER to confirm VGA as your selection. 5. Turn on the computer. PRESTIGIO P370MW...
4. Turn on the LCD TV, press the SOURCE button to open the Main Source menu. Select the correct input source and press ENTER. 5. Turn on the other LCD TV or video/audio recording device. NOTE: For more information, see the instructions supplied with the other LCD TV or video/audio recording device. PRESTIGIO P370MW...
4. Turn on your LCD TV, then press the SOURCE button to open the Main Source menu. Select the correct input source and press ENTER. 5. Turn on the other LCD TV or video/audio recording device. NOTE: For more information, see the instructions supplied with the other LCD TV or video/audio recording device. PRESTIGIO P370MW...
Press the VIEW MODE button to toggle between Wide, Normal, or Letter Box aspect ratios. Using the OSD 1. Press the MENU button to open the OSD main menu. 2. Press the > button three times to select the option icon and press ENTER to open the Set Up menu. PRESTIGIO P370MW...
To freeze the picture, press the FREEZE button. To resume live television press the FREEZE button again. 5.3 Using Twin Picture “Twin Picture” allows you to simultaneously view two pictures from two different sources on the same screen. The available options are: PRESTIGIO P370MW...
1. Press the SOURCE button to open the Main Source menu. 2. To select the input source for the main picture, press \/ or /\ to select a source from the list. Press ENTER to activate your selection. PRESTIGIO P370MW...
VGA, DVI, AV 1, AV 2, SCART 1, SCART 2, SCART 3, HDMI HDMI VGA, DVI, AV 1, SCART 1, SCART 2, SCART 3, TV Swapping the Main and Sub Pictures To exchange the two pictures, press the SWAP button on the remote control. PRESTIGIO P370MW...
8. Press /\ \/ < > to select the channel to be locked, then press ENTER. The channel number would be changed to red. If you want to unlock a channel, press /\ \/ < > to select the channel to be unlocked, then press ENTER. The channel number would be restored to white. 9. Press MENU or EXIT to exit. PRESTIGIO P370MW...
2. Press the > button three times to select the option icon. Press ENTER to open the Set Up menu. 3. Press /\ to select Next Page, then press ENTER. 4. Press < or > to select the desired time, then press ENTER to activate your selection. PRESTIGIO P370MW...
Press the MENU button on the remote control or right side panel to open the OSD main menu as shown. Video Mode The main menu contains five buttons for Picture, Sound, AV Connections, Set Up, and Child Lock sub-menus. PC Mode The main menu contains five buttons for Picture, Sound, Adjustment, Set Up, and Child Lock sub-menus. PRESTIGIO P370MW...
Press the MENU button to open the OSD main menu and press ENTER to open the Picture Menu. The Picture Menu allows you to adjust display settings such as contrast, brightness, colour temperature, etc. Menu options may vary depending on the input source. PRESTIGIO P370MW...
< to increase the red tones. Sharpness Adjusts the picture sharpness. > to sharpen the display. < to soften the display. Colour Temp Toggles the colour temperature between Warm, Normal, or Cool. > or < to select and ENTER to activate your selection. PRESTIGIO P370MW...
6.3 Sound Menu Press the MENU button to open the OSD main menu. Press ( once to select the speaker icon, then press ENTER to open the Sound Menu. The Sound Menu allows you to adjust sound effects. PRESTIGIO P370MW...
Page 44
This item is available only if you are currently in twin picture mode. > to select Sub. Main: selects the sound output from the main picture. < to select Main. Sub: selects the sound output from the sub picture. ENTER to activate your selection. PRESTIGIO P370MW...
> or < to select and ENTER to Y / C: S-Video connection. activate your selection. SCART2/SCART3 Auto: automatically detects the type of video input signal. > or < to select and ENTER to CVBS: composite video connection. activate your selection. RGB: component video connection. PRESTIGIO P370MW...
The adjusted value will depend on the screen resolution. < to move toward the left. V. Position Adjusts the vertical position of the video. > to move upward. The adjusted value will depend on the screen resolution. < to move downward. PRESTIGIO P370MW...
Channel > or < to select the channel which you want to adjust. Frequency: 45.25 ~ 864.25 MHz > / < to increase/decrease channel frequency in 0.05 MHz increments. ENTER to adjust channel frequency by pressing number keys. PRESTIGIO P370MW...
Page 48
OSD Language setting is not affected. Next Page Proceed to the next page of the menu. ENTER to go to the next page. To move to the second page of the Set Up menu, press \/ to select Next Page, then press ENTER. PRESTIGIO P370MW...
If the current input source is VGA / DVI / AV 1 / AV 2 / SCART 1 / SCART 2 / SCART 3 / HDMI, the Set Up menu appears as shown next. Press the \/ or /\ button to select an item in this menu and then make your changes. The following table describes all of the items in this menu. PRESTIGIO P370MW...
Press the \/ or /\ button to select an item in this menu and make your changes. The following table describes all of the items in this menu. PRESTIGIO P370MW...
Page 51
/\ \/ < > to select the channel to Programme to specify which channel will be blocked. be locked or unlocked and ENTER. The channel number would be changed to red to show the channel is locked or white to show the channel is not locked. PRESTIGIO P370MW...
You can see a picture but hear no sound. * Make sure that the volume is not turned down. * Make sure that the sound is not muted. * Make sure that your audio input source cables are connected securely and correctly. PRESTIGIO P370MW...
248 mm x 500 mm x 260 mm (Stand) VGA D-sub 15-pin x 1 115.75 mm x 806 mm x 90 mm (Speaker) DVI-D x 1 Net Weight Audio 15 kg (LCD TV) Mini-stereo (3.5 mm) x 1 3.4 kg (Stand) 1.9 kg (Speaker) PRESTIGIO P370MW...
480i, 480p, 576i, 576p, 720p, 1080i Audio TV System Compatibility L/R RCA x 2 AV: NTSC/PAL/SECAM HDTV Input TV: PAL/SECAM Video Component RCA x 1 (YPbPr/YCbCr) Audio Audio L/R RCA x 2 Speaker Drivers 2-Way Stereo (Tweeter and Mid Range) PRESTIGIO P370MW...
Page 55
Regulatory Compliance CE, TUV Dimensions H x W x D 574.4 mm x 938.8 mm x 110 mm (LCD TV) NOTE: Because we continually strive to improve our products we may change specifications and designs without prior notice. PRESTIGIO P370MW...