Advertisement
BATWING™ QUADROCOPTER DIAGRAM
Propeller Guard
The safety guard is easy to clip on and off. Simply pull the clips away
from each motor mount and remove the BATWING™ from below.
Note: Always have the safety guard attached when flying in SPEED Mode 1.
REMOTE DIAGRAM
Speed Setting Button
Power Indicator
Speed Indicator
Left Bank Trim
Throttle/Yaw
3 CH Mode
REMOVABLE CONTROLLER GRIPS
Easily slides off and on. (see remote diagram)
3
Li-Poly Battery Compartment
Propeller Blade
Callibrate
360˚ Stunt Rolls Button
Forward Trim
Power On/Off
3/4 Ch indicator
Right Bank Trim
Direction Control
Removable grip
Extender
4 CH Mode
Backward Trim
WARNING
DO NOT FLY YOUR BATWING™ IN FOUL WEATHER!
PREPARING FOR FLIGHT
• Verify that there are 2 "AAA" batteries inside the remote control unit and the BATWING™
has been fully charged.
• Make sure to be in a large space with an open radius of at least 50 feet.
• Make sure the empty space has no obstacles or bodies of water. Set your BATWING™ on a
clean flat surface before take-off.
DO NOT ATTEMPT TO FLY YOUR BATWING™ IF THERE IS RAIN, SNOW, HEAVY WINDS, THUNDER OR LIGHTNING
OUTDOORS. IT COULD DAMAGE YOUR PRODUCT AND POSSIBLY EVEN CAUSE BODILY HARM.
SYNCING YOUR BATWING™
Important! When syncing your BATWING™ drone with the controller always make sure that the
drone is on a flat level surface. This insures that the 6 Axis gyro is properly programmed to
mimic your trim settings.
Your BATWING™ utilizes an automatic 2.4G channel selection system that allows up to
8 people to fly side by side in the same wireless range.
FOR ONE PERSON PLAY:
1.
Before starting, make sure that the power on your controller is in the OFF position
and BATWING™ battery is disconnected. Make sure that there are no other 2.4G devices
in the area as well.
2.
Insert the battery into the BATWING™ to turn on and set it down on a flat surface.
The white and red LED indicators of the BATWING™ should flash rapidly.
3.
ON the remote , pull the throttle all the way down, then turn ON your remote and
You will hear 2 short beeps, the white and red LED lights SHOULD STAY SOLID, Push the
throttle all the way up and pull it down, your BATWING™ and remote should have
successfully synced. Should this not happen, repeat all steps again.
FOR MULTI PERSON PLAY:
4.
Before starting, make sure that the power on all BATWING™ and Controllers are in
the OFF position. Make sure that there are no other 2.4G devices in the area as well.
5.
Each person will have to sync their BATWING™ individually at a different time to avoid
interference. Follow steps 1 to 3 above making sure to keep away from other people
while also making sure that no one else is syncing at the same time.
6.
After syncing a players BATWING™ it should be left ON until all players have synced
their BATWING™.
7.
Should there be a mistake/interference, all players must turn off their controllers
and BATWING™ and start the process all over again.
FLYING TIPS
• It is recommended that you operate the BATWING™ in a wide space. The ideal space
shoulhave a 200 foot radius.
• Parental guidance or adult supervision is suggested at all times.
• If you are flying the BATWING™ with others, make sure all spectators are behind you.
• For best performance, it is recommended that you operate the BATWING™ in zero wind
conditions. Wind can greatly affect the performance of the BATWING™.
4
Hide quick links:
Advertisement
