Philips AVENT SCD860 Manual page 2

ENGLISH
IMPORTANT
This baby monitor is intended as an aid. It is not a substitute for
responsible and proper adult supervision and should not be used as such.
Never leave your baby alone in your home. Always make sure there is someone
present to look after the baby and take care of its needs.
Disclaimer
Please note that you use this baby monitor at your own risk. Koninklijke Philips
Electronics NV and its subsidiary companies are not responsible for the operation
of this baby monitor or your use of it and therefore do not accept any liability in
connection with your use of this baby monitor.
Introduction
Congratulations on your purchase and welcome to Philips Avent! To benefit fully from
the support that Philips Avent offers, register your product at www.philips.com/
welcome.
This short manual contains important information about your uGrow baby monitor
and offers brief instructions on how to set up the baby monitor and the app.
For more detailed information and the complete user manual, please visit
www.philips.com/ugrow.
Important safety information
Read this information carefully before you use the appliance and save it for future
reference.
Danger
- Never immerse any part of the baby monitor in water or any other liquid.
Do not place the appliance where water or any other liquid can drip or splash
onto it. Never use the baby monitor in moist places or close to water.
- Never put any object on top of the baby monitor and do not cover it. Do not
block any ventilation openings. Install according to the manufacturer's instructions.
- Cords present a potential strangulation hazard. Keep cords out of the reach of
children (more than 1 metre/3.5 feet away). Never place the baby monitor inside
or above the baby's bed or playpen (Fig. 1).
Warning
- Check if the voltage indicated on the adapter corresponds to the local mains
voltage before you connect the appliance.
- Do not modify and/or cut and/or change any part of the adapter, this causes
a hazardous situation.
- Only use Philips recommended adapter.
- If the adapter is damaged, have it replaced with one of the original type to avoid
a hazard.
- Do not open the housing of the baby monitor to prevent an electric shock.
- This appliance is not intended for use by persons (including children) with
reduced physical, sensory or mental capabilities, or lack of experience and
knowledge, unless they have been given supervision or instruction concerning
use of the appliance by a person responsible for their safety.
- Children should be supervised to ensure that they do not play with the appliance.
- Protect the power cord from being walked on or pinched particularly at plugs,
convenience receptacles, and the point where they exit from the apparatus.
- Make sure that you install the baby monitor in such a way that its cord does not
obstruct a doorway or passage. Make sure the cord does not lie on the floor
where it presents a tripping hazard.
- Keep the packaging materials (plastic bags, cardboard buffers, etc.) out of the
reach of children, as they are not a toy.
- Keep screws and small items out of the reach of the baby.
Caution
- This baby monitor is intended as an aid. It is not a substitute for responsible and
proper adult supervision and should not be used as such.
- Make sure the baby monitor and the cord are always out of reach of the baby
(at least 1 metre/3.5 feet away) (Fig. 2).
- Use the appliance at a temperature between 0°C (32°F) and 40°C (104°F).
- Do not mount the baby monitor on or above the baby's bed or playpen.
- Do not install near any heat sources such as radiators, heat registers, stoves or
other apparatus (including amplifiers) that produce heat.
- Make sure that your hands are dry when you insert the appliance plug into the
appliance and the adapter into the wall socket.
- If you place the baby monitor on a table or low cabinet, do not let the mains
cord hang over the edge of the table or worktop. People may trip over cords.
Compliance with standards
- This appliance complies with all applicable standards and regulations regarding
exposure to electromagnetic fields.
- This product complies with the radio interference requirements of the
European Community (Fig. 3).
- Philips hereby declares that this baby monitor is in compliance with the essential
requirements and other relevant provisions of Directive 1999/5/EC. A copy of
the EC Declaration of Conformity (DoC)
is available online at www.philips.com/support.
Privacy
Philips believes strongly in protecting the privacy of the personally identifiable
information you share with us through the app. We also believe it is important to
inform you about the use of those data. Therefore, we encourage you to read the
privacy notice in the app carefully. You can also find information on our privacy policy
on our website.
Product overview (Fig. 4)
1 WiFi status light
2 Infrared lights
3 Baby monitor lens
4 Microphone
5 Viewing indicator
6 Nightlight
7 Foot
8 Nightlight button with status indication
9 Lullaby play/pause button with status indication
10 Light sensor
11 Temperature and humidity sensor unit
12 Appliance plug socket
13 Reset button
14 On/off button
15 Wall mounting bracket
16 Adapter
17 Appliance plug
First-time setup
Before you start the set-up procedure, make sure:
- You have wireless Internet access (2.4 GHz WiFi).
- You are close enough to the WiFi router to have a good WiFi signal.
- If you use a WiFi repeater, make sure that your router and your WiFi repeater
have the same SSID and that you use the same password for the router and
the repeater.
- You have the password of your WiFi network at hand. Always connect the baby
monitor to a secure network (see chapter 'Security and privacy' in the user
manual available online at www.philips.com/ugrow).
- Make sure that your smart device runs on iOS 7 or higher, or Android 4.1
or higher.
1 Download the Philips Avent uGrow Smart Monitor app from the App Store or
Google Play. Use keywords 'uGrow smart monitor' or 'Philips smart monitor'
to find the app.
2 Launch the app.
3 Follow the set-up instructions in the app.
Mounting the baby monitor on the wall
The baby monitor comes with a wall mounting bracket. Before you mount the baby
monitor on the wall, make sure there is a good WiFi signal at the point where you
want to mount the baby monitor. Follow the instructions below to fasten the
wall mounting bracket to the wall and to attach the baby monitor onto the wall
mounting bracket.
1 Use a pencil to put a cross on the wall at the place where you want to mount
the baby monitor. (Fig. 5)
2 Hold the wall mounting bracket to the wall. Make sure that one of the holes is
right over the cross that you put on the wall at step 1.
Note: Make sure that the ring of the wall mounting bracket slants downward when you
hold it to the wall. If the ring of the wall mounting bracket slants upward, turn the wall
mounting bracket the other way around so that it is in the correct position (Fig. 6).
3 Use a pencil to mark the other screw hole on the wall (Fig. 7).
4 Drill 2 holes in the wall at the marks (Fig. 8).
5 Use 2 screws to fasten the wall mounting bracket to the wall. Tighten the screws
with a screwdriver (Fig. 9).
6 Pass the humidity and temperature sensor unit through the hole in the wall
mounting bracket. Then align the slots in the foot of the baby monitor with the
projections on the ring. Fit the groove in the foot of the baby monitor onto the
raised edge on the inside of the ring (Fig. 10).
7 Turn the foot of the baby monitor clockwise to position the baby monitor (Fig. 11).
8 Insert the appliance plug into the appliance plug socket in the temperature and
humidity sensor unit and insert the adapter into a wall socket. Now your baby
monitor is ready for use (Fig. 12).
WiFi status light signals
1 Off
- The baby monitor is off
2 Orange
- Flashes fast: the baby monitor is starting up.
- Flashes slowly: the baby monitor is upgrading its firmware. Do not switch the
baby monitor off during the firmware upgrade.
Note: The WiFi status light might switch off shortly during the firmware upgrade.
- Solid: the camera of the baby monitor is ready to read the WiFi QR code
generated by your smartphone or tablet.
3 Green
- Flashes slowly: the WiFi QR code has been read successfully.
- Solid: the baby monitor is connected to the WiFi network.
4 Red
- Flashes slowly: the WiFi password entered is wrong.
- Solid red: the baby monitor fails to connect to the WiFi network.
Resetting the baby monitor
The baby monitor has a reset button on the back. When you press this button the
baby monitor is reset to its factory default settings.
Note: Always reset the baby monitor by pressing the reset button and delete your account
before you transfer the baby monitor to someone else. This is necessary to protect
your privacy.