Subscribe to Our Youtube Channel
Related Manuals for Trust 350FS POWERC@M FLASH
Summary of Contents for Trust 350FS POWERC@M FLASH
- Page 1 TRUST 350FS POWERC@M FLASH User’s manual Ver. 13137-02 T R U S T . C O M L I F E I S M O R E ! T R U S T U S...
- Page 2 Thank you for your purchase. Register your product via our Internet site at www.trust.com/register, so that you will be eligible for optimal guarantee and service support. You will also be automatically informed of the development of your and other Trust products. T R U S T . C O M...
- Page 3 TRUST 350FS POWERC@M FLASH Figures Fig. 1 Fig. 2 Fig. 3 Fig. 4 Fig. 5 T R U S T . C O M L I F E I S M O R E ! T R U S T U S...
- Page 4 TRUST 350FS POWERC@M FLASH Fig. 6 Fig. 7 Fig. 8 Fig. 9 T R U S T . C O M L I F E I S M O R E ! T R U S T U S...
-
Page 5: General Information
(13) Introduction This instruction manual is for users of the Trust 350FS PowerC@m Flash. Basic This instruction manual is for users of the Trust 350FS PowerC@m Flash. Basic knowledge of computers is necessary to be able to install this product. -
Page 6: Camera Memory
The warranty will then no longer be valid. NOTE: The camera will make a noise when the battery voltage becomes too low. Close the battery flap again by gently pushing it and sliding it upwards. The Trust 350FS PowerC@m Flash is now ready for use. -
Page 7: Camera Functions
TRUST 350FS POWERC@M FLASH Camera functions NOTE: The model of the camera shown below may be different from your camera. The functionality and the position of the buttons and display are, however, the same. Function Description Exposure button Takes a photograph. -
Page 8: Using The Camera
You see the number on the display is increased by ‘1’ so one photograph is taken. Setting the resolution The Trust 350FS PowerC@m Flash can be used to take photographs in two different resolutions, i.e. VGA (640 x 480, approx. 60 recordings) and CIF (320 x 240, approx. - Page 9 6.3. Setting the Macro button The Trust 350FS PowerC@m Flash has a Macro function which is set by sliding the MACRO button (10) upwards or downwards. The functions are described in the table below.
-
Page 10: Setting The Flash
Setting the flash The flash of the Trust 350FS PowerC@m Flash has two settings, i.e. and Auto The default setting when the camera is turned on is OFF. -
Page 11: Continuous Mode
NOTE: The video function only works in the low (CIF) resolution. The TRUST 350FS POWERC@M can be used to take a number of photographs, one after another, using the CONTINUOUS mode. Turn the camera on by pressing the ON/OFF button (7). A beep will be heard when the camera is turned on. -
Page 12: Deleting Recordings
'Setup.exe' on the CD-ROM. Figure 3 will appear. The Trust Software Installer will appear in Windows 98, Windows ME, Windows 2000 and Windows XP. Click on ‘350FS PowerC@m Flash’ to start the installation. Figure 4 will appear. Click on ‘Next’ to start the installation and follow the on-screen instructions. -
Page 13: Installing The Software
TRUST 350FS POWERC@M FLASH Select the option to restart your computer and click on 'Finish'. Start the Trust Software Installer again (see figure 3) after your computer has been restarted so that you can install the other software. See chapter 6 for instructions on how to install the other software. -
Page 14: Checking After The Installation
There are a number of conditions attached to the use of this site. The conditions can be found at www.trustphotosite.com. This software can be used to upload your photographs to the Trust Photo Site. Note: The latest version of the Trust Photo Upload software can always be downloaded from the Trust website. - Page 15 TRUST 350FS POWERC@M FLASH 13.2 Using Trust Photo Site You must first register with Trust before you can upload photographs to the Trust Photo Site. 13.2.1 Registeration and create your Trust user account 13.2.1.1 Register first Go to Trust website (www.trust.com) to register yourself and your camera.
-
Page 16: Using The Software
CD. 14.2 Video Impression 1.6 Video Impression 1.6 can be used to make video recordings with your TRUST 350FS POWERC@M FLASH. NOTE: This function only works if the camera has been connected to your PC using the USB cable provided with the camera. -
Page 17: Troubleshooting
TRUST 350FS POWERC@M FLASH Troubleshooting Method Read the solutions given below. Check for up-to-date FAQ’s, drivers and instruction manuals on the Internet (www.trust.com/13137). Problem Cause Possible solution The computer's USB Try a different USB port or Windows does not port does not work. - Page 18 Internet. information. If you still have problems after trying these solutions, please contact one of the Trust Customer Care Centers. You can find more information at the back of this instruction manual. Please have the following information available: •...
-
Page 19: Warranty Conditions
TRUST 350FS POWERC@M FLASH Warranty conditions Our products have a two-year manufacturer's warranty which is effective from the date of purchase. If there is a fault, return the product to your dealer and include an explanation of the fault, the proof of purchase and all the accessories. -
Page 20: Customer Care Centers
CUSTOMER CARE CENTERS 24 HOURS free service: www.trust.com Residents in the UK and Ireland should contact: UK Office Mon - Fri Phone +44-(0)845-6090036 From 8:00 - 16:00 +31-(0)78-6543299 I residenti in Italia possono contattare: lun - ven Ufficio italiano 9:00 - 13:00 /...
Need help?
Do you have a question about the 350FS POWERC@M FLASH and is the answer not in the manual?
Questions and answers