Ikra LSN 2600 E Operating Instructions Manual page 25

• Only operate the tool during broad daylight or
with adequate artificial light.
• When the tool is not in use, store it in a dry
place and out of reach of children.
• After use, disconnect the tool from the power
supply and check for damage. If you have the
slightest doubts, contract an authorized service
centre.
• Only use the tool according to the instructions
given in this manual.
• Check regularly that screws are tight.
• Use only spare parts and accessories recom-
mended by the manufacture.
• Do not try to repair the tool or access internal
parts. Contract authorized service centers only.
• This product is not intended for use by persons
(including children) with reduced physical, sen-
sory or mental capabilities, or lack of experi-
ence and knowledge.
• Children should be supervised to ensure that
they do not play with the product.
• Cleaning and maintenance may not be carried
out by children.
• Never allow children or people unfamiliar with
the instructions to use the machine.
• Have your dealer or a specialist show you how
to operate your trimmer.
• Local regulations may restrict the age of the
operator.
• Before use, examine the cable for signs of
damage, or ageing. Do not use the product if
the electric cables are damaged or worn.
• Arrange the extension cord so that it cannot
be damaged and does not cause a hindrance.
• If the cord is damaged during utilisation, it
must be disconnected immediately from the
mains. DO NOT TOUCH THE CABLE BE-
FORE YOU HAVE DISCONNECTED IT FROM
THE MAINS, since damaged cable result in
contact with live parts.
• Only use a weatherproof extension cord with
a connector unit according to IEC 60320-2-3.
• Only extension cords of type H05W-F, H05RN-
F or IEC (60227 IEC 53, 60245 IEC 57) may
be used.
• If you want to use an extension cable when op-
erating your product, only the following cable
dimensions should be used:
2
– 1.0 mm : max. length 40 m
2
– 1.5 mm : max. length 60 m
2
– 2.5 mm : max. length 100 m
• Note: If an extension cable is used it must be
earthed and connected through the plug to the
earth cable of your supply network in accord-
ance with prescribed safety regulations.
• The device should be operated via a residual
current circuit breaker (RCD) with a triggering
current of max. 30 mA.
• Couplings and plugs must be splashwater-
proof.
• Make sure to have a safe stand when working
on inclines.
• Move the tool at walking speed only.
• Inspect the collection bag regularly. If the
collection bag becomes worn or damaged,
replace.
• Warning! Do not touch moving dangerous
parts before the mains plug has been un-
plugged and the moving dangerous parts have
come to a complete standstill.
• Warning! NEVER use the machine in bad
weather, particularly, if there is a risk of light-
ning!
• Warning! Never operate the machine with de-
fective safety equipment or covers or without
safety equipment.
• Keep the extension cord away from moving
dangerous parts to avoid damage to the ca-
bles, which can result in contact with live parts.
• Do not operate the machine barefoot or while
wearing open sandals. Avoid wearing loose
fitting clothing or clothing with hanging strings
or ties.
• Operate the machine in the recommended po-
sition and only on a firm, level surface.
• Prior to use, always perform a visual inspection
to determine whether the shredder, the bolts of
the shredder and other fasteners are secured,
that the housing is not damaged and that the
safety equipment and protective screens are
mounted. Replace worn or damaged compo-
nents in sets to maintain the balance. Replace
damaged or unreadable labels.
• Prior to starting the machine, make sure that
the feeding unit is empty.
• Keep your face and body away from the filling
opening.
• Make sure your hands, other body parts or
clothing are not in the feeing unit, the discharge
channel or in the vicinity of moving parts.
• When feeding material, never stand on a level
that is higher than the level of the machine
base.
• When operating the machine, do not remain in
the discharge zone.
• When feeding material into the machine, use
GB-5