Fisher FIELDVUE DVC2000 Instruction Manual
  1. Manuals
  2. Brands
  3. Fisher Manuals
  4. Control Unit
  5. FIELDVUE DVC2000
  6. Instruction manual

Fisher FIELDVUE DVC2000 Instruction Manual

Digital valve controller
Hide thumbs Also See for FIELDVUE DVC2000:
Table of Contents

Advertisement

Quick Links

See also: Instruction Manual Supplement
Instruction Manual
D103176X012
Fisher
FIELDVUE
™
Controller
This manual applies to
Instrument Level
Device Type
Device Revision
Hardware Revision
Firmware Revision
DD Revision
Contents
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . .
Section 2 Detailed Setup and Calibration via
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . .
HART Tag
Message
Descriptor
Date
Valve Serial Number
Instrument Serial Number
Polling Address
LUI Language
www.Fisher.com
™
DVC2000 Digital Valve
HC, AD, PD
AC
05
F5
1
1
1 & 2
1 & 2
1, 2, 3, 4 & 5
1, 2, 3, 4 & 5
3
1
. . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . .
W8755
.
3
3
3
3
Analog Input Range High and Low
4
4
Temperature Units
7
8
Maximum Supply Pressure
Actuator Style
9
Valve Serial Number
9
Valve Style
9
Zero Control Signal
9
9
Tuning Set
10
Damping Factor
10
Expert Tuning Gains
10
Input Characteristic
12
Custom Characteristic Table
14
Set Point Filter Time
Limits and Cutoffs
Minimum Opening and Closing Time
DVC2000 Digital Valve Controller
. . . . . . . . . . .
. . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . .
June 2017
15
16
16
19
20
22
23
23

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the FIELDVUE DVC2000 and is the answer not in the manual?

Questions and answers

Related Manuals for Fisher FIELDVUE DVC2000

Summary of Contents for Fisher FIELDVUE DVC2000

  • Page 1: Table Of Contents

    Instruction Manual DVC2000 Digital Valve Controller D103176X012 June 2017 ™ Fisher FIELDVUE DVC2000 Digital Valve ™ Controller This manual applies to Instrument Level HC, AD, PD Device Type Device Revision Hardware Revision 1 & 2 1 & 2 Firmware Revision 1, 2, 3, 4 &...
  • Page 2 Instruction Manual DVC2000 Digital Valve Controller June 2017 D103176X012 Self-Test Failure for Instrument Shutdown ..Section 4 Maintenance and Transmitter/Switches ..... . . Troubleshooting .

  • Page 3: Section 1 Introduction And Specifications

    QR code at the right, contact your field support Emerson sales office, Local Business Partner, or visit our website at Fisher.com. Scope of Manual This instruction manual is a supplement to the quick start guide that ships with every instrument. This instruction manual includes specifications, detailed configuration and calibration using a Field Communicator, maintenance and troubleshooting information and replacement part details.

  • Page 4: Terminology

    Instruction Manual Introduction and Specifications June 2017 D103176X012 Terminology Instrument Level— There are four (4) levels of functionality available: AC, HC, AD and PD. AC—This level provides the capability to setup and calibrate the positioner through the LCD or the Field Communicator.
  • Page 5 D103176X012 Table 1‐1. Specifications Available Configurations Temperature Limits Integral mounting to the Fisher GX Control Valve -40 to 85_C (-40 to 185_F). LCD may not be readable below -20_C (-4 _F). and Actuator System J Sliding-stem applications Quarter-turn rotary applications...
  • Page 6 Housing and Cover: A03600 low copper aluminum Declaration of SEP alloy Elastomers: nitrile, fluorosilicone Fisher Controls International LLC declares this product to be in compliance with Article 4 paragraph Stem Travel 3 of the PED Directive 2014/68/EU. It was designed and manufactured in accordance with Sound Minimum: 6.35 mm (0.25 inch)

  • Page 7: Related Documents

    D HART Field Device Specification - Fisher FIELDVUE DVC2000 Digital Valve Controller (D103783X012) D Using the HART Tri-Loopt HART-to-Analog Signal Converter with Fisher FIELDVUE Digital Valve Controllers (D103267X012) These documents are available from your Emerson sales office, Local Business Partner, or at Fisher.com.

  • Page 8: Educational Services

    Instruction Manual Introduction and Specifications June 2017 D103176X012 Educational Services For information on available courses for the DVC2000 digital valve controller, as well as a variety of other products, contact: Emerson Automation Solutions Educational Services - Registration Phone: 1-641-754-3771 or 1-800-338-8158 E-mail: education@emerson.com emerson.com/fishervalvetraining...

  • Page 9: Hart Communication

    Instruction Manual Detailed Setup and Calibration D103176X012 June 2017 Section 2 Detailed Configuration and Calibration via HART Communication 2‐2‐ Detailed Setup The DVC2000 digital valve controller has the capability to communicate via the HART protocol. This section describes the advanced features that can be accessed with the Field Communicator. Table 2‐1 lists the default settings for a standard factory configuration.

  • Page 10: Restart Control Mode

    Instruction Manual Detailed Setup and Calibration D103176X012 June 2017 calibration or stroke valve. However, if you abort from a procedure where the instrument is in the Test mode, it may remain in this mode. To take the instrument out of the Test mode, select Control Mode then select either Analog or Digital.
  • Page 11 Instruction Manual Detailed Setup and Calibration D103176X012 June 2017 Table 2‐1. Factory Default Detailed Setup Parameters Setup Parameter Default Setting Control Mode Analog Restart Control Mode Resume Last Burst Mode Enabled Burst Mode Command HART Tag As specified on order Message Blank Description...

  • Page 12: Protection

    30, 30i 34, 34i, 40, 40i Spring & Diaphragm SStem-Standard 45, 45i, 50, 50i 46, 46i, 60, 60i, 70, Undefined 70i, 76, 76i & 80-100 Fisher 20, 30, 33, 1051 & 1052 Spring & Diaphragm Undefined Rotary 40, 60, 70 1066SR...
  • Page 13 June 2017 Table 2‐3 lists configurable parameters in the instrument and the requirements for modifying these parameters, in terms of instrument mode and protection. Table 2‐3. Conditions for Modifying FIELDVUE DVC2000 Digital Valve Controller Parameters In Service/ In Service/ Out of Service/...

  • Page 14: General Information

    Instruction Manual Detailed Setup and Calibration D103176X012 June 2017 Table 2‐3. Conditions for Modifying FIELDVUE DVC2000 Digital Valve Controller Parameters In Service/ In Service/ Out of Service/ Out of Service/ Parameters Config Protected Config Unprotected Config Protected Config Unprotected Drive Alert Enable...

  • Page 15: Measured Variable Units And Ranges

    Instruction Manual Detailed Setup and Calibration D103176X012 June 2017 Measured Variable Units and Ranges Field Communicator Setup & Diag > Detailed Setup > Measured Var (1-2-4) Follow the prompts on the Field Communicator to define the following measured variables units and ranges: D Analog In Units—Permits defining the Analog Input Units in mA or percent of 4-20 mA range.

  • Page 16: Pressure Units

    Instruction Manual Detailed Setup and Calibration D103176X012 June 2017 Actuator and Valve Information Field Communicator Setup & Diag > Detailed Setup > Actuator & Valve (1-2-5) Follow the prompts on the Field Communicator to edit or view information in the following fields: D Max Supply Press—Enter the maximum supply pressure in psi, bar, or kPa, depending on what was selected for pressure units.
  • Page 17 Instruction Manual Detailed Setup and Calibration D103176X012 June 2017 Table 2‐4. Gain Values for Preselected Turning Sets Minor Loop Feedback Tuning Set Proportional Gain Velocity Gain Gain D Damping Factor—If after selecting a tuning set the valve travel overshoot is excessive or unsatisfactory, the damping factor allows you to either decrease damping to allow more overshoot, or increase damping to decrease the overshoot.
  • Page 18 Instruction Manual Detailed Setup and Calibration D103176X012 June 2017 Figure 2‐2. Travel Target Versus Ranged Set Point, for Various Input Characteristics (Zero Control Signal = Closed) Ranged Set Point, % Ranged Set Point, % −25 −25 Input Characteristic = Linear Input Characteristic = Equal Percentage −25 Ranged Set Point, %...

  • Page 19: Integral Settings

    Instruction Manual Detailed Setup and Calibration D103176X012 June 2017 Travel Limit Lo—Defines the low limit for the travel in percent (%) of ranged travel. It is the minimum allowable travel (in percent of ranged travel) for the valve. During operation, the travel target will not exceed this limit. When a Travel Limit Low is set, the Travel Cutoff Low is deactivated, since only one of these parameters can be active.

  • Page 20: Travel Alerts

    Instruction Manual Detailed Setup and Calibration D103176X012 June 2017 Setting Travel Alerts Setting High, High-High, Low and Low-Low Alerts Follow the prompts on the Field Communicator to set the following travel alerts: D Tvl Hi/Lo Enab—Yes or No. Travel Hi/Lo Enable activates checking of the ranged travel against the Travel Alert High and Low Points.
  • Page 21 Instruction Manual Detailed Setup and Calibration D103176X012 June 2017 D Tvl Alrt DB—Travel Alert Deadband is the travel, in percent (%) of ranged travel, required to clear a travel alert, once it has been set. The deadband applies to both Travel Alert Hi/Lo and Travel Alert Hi Hi/Lo Lo. See figure 2‐3. Note The Travel Alert Deadband applies to the Travel Deviation as well as Travel Alert Hi/Lo and Travel Alert Hi Hi/Lo Lo.

  • Page 22: Cycle Counter Alert

    Instruction Manual Detailed Setup and Calibration D103176X012 June 2017 Figure 2‐4. Travel Accumulator Deadband (set at 10%) DEADBAND EXCEEDED, NEW REFERENCE POINT ESTABLISHED THIS AMOUNT OF CHANGE IS DEADBAND REFERENCE POINT ADDED TO THE TRAVEL ACCUMULATOR. DEADBAND (+/- 5%) A6534 Cycle Counter Alert Follow the prompts on the Field Communicator to set the following cycle counter alerts: D Cycl Cnt Alrt Enab—Yes or No.

  • Page 23: Other Alerts

    Instruction Manual Detailed Setup and Calibration D103176X012 June 2017 D Cycle Count—Cycle Counter records the number of times the travel changes direction. The change in direction must occur after the deadband has been exceeded before it can be counted as a cycle. See figure 2‐5. You can reset the Cycle Counter by configuring it as zero.

  • Page 24: Self-Test Failure For Instrument Shutdown

    Instruction Manual Detailed Setup and Calibration D103176X012 June 2017 Self Test Failures for Instrument Shutdown Field Communicator Setup & Diag > Detailed Setup > Self Test Shutdown (1-2-8) Upon shutdown, the instrument attempts to drive its output pressure to the zero current condition and no longer executes its control function.

  • Page 25: Transmitter/Switches

    Instruction Manual Detailed Setup and Calibration D103176X012 June 2017 Transmitter/Switches Field Communicator Setup & Diag > Detailed Setup > Transmitter/Switches (1-2-9) Note These menu items are only available on units that have the optional position transmitter / limit switch hardware installed. If optional limit switches are being used, power must be applied to the switch circuits throughout the calibration routine.

  • Page 26: Tuning

    The auto tuner is used to optimize digital valve controller tuning. It can be used on most sliding-stem and rotary designs, including Fisher and other manufacturers' products. Moreover, because the auto tuner can detect internal instabilities before they become apparent in the travel response, it can generally optimize tuning more effectively than manual tuning.

  • Page 27: Calibration

    Instruction Manual Detailed Setup and Calibration D103176X012 June 2017 Calibration Field Communicator Calibrate > Calibrate (1-4) WARNING During calibration the valve will move full stroke. To avoid personal injury and property damage caused by the release of pressure or process fluid, isolate the valve from the process and equalize pressure on both sides of the valve or bleed off the process fluid.

  • Page 28: Using Local Operator Interface

    Instruction Manual Detailed Setup and Calibration D103176X012 June 2017 6. The following message appears: Use Increase and Decrease selections until the displayed current matches the target. Press OK when you have read this message. 7. The value of the Analog Input appears on the display. Press OK to display the adjustment menu. 8.

  • Page 29: Manual Calibrate Travel

    Instruction Manual Detailed Setup and Calibration D103176X012 June 2017 Adjusting the output bias aligns the travel set point with the actual travel by computing the drive signal required to produce 0% error. This is done while the valve is at 50% travel, making very small adjustments. 2.

  • Page 30: Pressure Sensor Calibration

    Instruction Manual Detailed Setup and Calibration D103176X012 June 2017 1. From the adjustment menu, select the direction and size of change required to set the travel at 0%. If another adjustment is required, repeat step 1. Otherwise, select Done and go to step 2. 2.

  • Page 31: Position Transmitter

    Instruction Manual Detailed Setup and Calibration D103176X012 June 2017 Press OK when you have read the message. 6. The value of the output pressure appears on the display. Press OK to display the adjustment menu. 7. From the adjustment menu, select the direction and size of adjustment to the displayed value. Selecting large, medium, and small adjustments causes changes of approximately 3.0 psi/0.207 bar/20.7 kPa, 0.30 psi/0.0207 bar/2.07 kPa, and 0.03 psi/0.00207 bar/0.207 kPa, respectively.
  • Page 32 Instruction Manual Detailed Setup and Calibration D103176X012 June 2017...

  • Page 33: Section 3 Viewing Device Variables And Diagnostics

    Instruction Manual Viewing Device Variables and Diagnostics D103176X012 June 2017 Section 3 Viewing Device Variables and Diagnostics3‐3‐ Viewing Variables Note These variables are not available for instrument level AC. Analog Input, Travel, Valve Set Point, Drive Signal and Output Pressure The following variables are displayed on the Online menu: Analog In shows the value of the instrument analog input in mA (milliamperes) or % (percent) of ranged input.

  • Page 34: Viewing Device Information

    D Device Rev—Device Revision is the revision number of the software for communication between the Field Communicator and the instrument. D Firmware Rev—Firmware Revision is the revision number of the Fisher firmware in the instrument. D Firmware Date—Firmware Date is the revision date of the firmware being used.

  • Page 35: Viewing Instrument Status

    Instruction Manual Viewing Device Variables and Diagnostics D103176X012 June 2017 Viewing Instrument Status Field Communicator Instrument Status (7) Note Instrument Status is not available for instrument level AC. The following describes the various displays for the Instrument Status menu. D Done—Select this when you are done viewing the instrument status. Note Alerts are not available with instrument level AC.
  • Page 36 Instruction Manual Viewing Device Variables and Diagnostics D103176X012 June 2017 D Failure Alerts—If a self-test failure has occurred, it will appear when the Failure Alerts menu item is selected. If there are multiple failures, they will appear on the display one at a time in the order listed below. 1.
  • Page 37 Instruction Manual Viewing Device Variables and Diagnostics D103176X012 June 2017 D Operational Status—This menu item indicates the status of the Operational items listed below. The status of more than one operational may be indicated. If more than one Operational status is set, they will appear on the display one at a time in the order listed below.
  • Page 38 Instruction Manual Viewing Device Variables and Diagnostics D103176X012 June 2017...

  • Page 39: Section 4 Maintenance And Troubleshooting

    Instruction Manual Maintenance and Troubleshooting D103176X012 June 2017 Section 4 Maintenance and Troubleshooting4‐ 4‐ The DVC2000 digital valve controller has the capability to provide predictive maintenance information through the use of ValveLink software. This software allows you to pinpoint instrument and valve problems without disrupting the process.

  • Page 40: Replacing The Instrument

    Instrument Removal 1. Make sure that the valve is isolated from the process. 2. Remove the instrument cover (refer to figure 4‐1). Figure 4‐1. FIELDVUE DVC2000 Exploded View TERMINAL BOARD SCREWS (3) EMI SHIELD SCREWS (3) MAIN ELECTRONIC SCREWS (3)

  • Page 41: Replacing The Magnetic Feedback Assembly

    Instruction Manual Maintenance and Troubleshooting D103176X012 June 2017 6. Remove the bolts connecting the DVC2000 housing to the mounting bracket. Note The magnet assembly may remain on the valve stem (or shaft). When replacing the instrument, be sure to follow the mounting procedure outlined in the quick start guide (D103203X012) that shipped with the digital valve controller.
  • Page 42 Instruction Manual Maintenance and Troubleshooting D103176X012 June 2017 Note After I/P converter replacement, calibrate the digital valve controller to maintain accuracy specifications. Removal 1. Remove the main cover. 2. Remove three screws that hold the EMI shield and remove the shield (refer to figure 4‐1). 3.

  • Page 43: Replacing The Pneumatic Relay

    Instruction Manual Maintenance and Troubleshooting D103176X012 June 2017 Assembly When installing a new I/P converter, follow the reverse procedure as outlined above and recalibrate the instrument. 1. Install the I/P converter, making sure the screen O-ring is installed on the I/P supply port (the circular port on the mounting frame), and that the two manifold O-rings are in place.

  • Page 44: Troubleshooting

    Instruction Manual Maintenance and Troubleshooting D103176X012 June 2017 Troubleshooting What is a healthy unit? In order to troubleshoot the DVC2000 digital valve controller, it is critical to understand how a healthy unit is supposed to behave. Below is a list of behaviors you should see if the instrument is performing well. D LCD correctly displaying characters D Pushbuttons allow navigation D Valve travels full stroke...
  • Page 45 Instruction Manual Maintenance and Troubleshooting D103176X012 June 2017 4. Check the alerts via HART 5. Check the feedback setup Is the pole piece on the DVC2000 housing within the valid travel range of the feedback array? 6. Observe the stem movement and pressure delivery Determine the logical causes.

  • Page 46: Checking Available Voltage

    Instruction Manual Maintenance and Troubleshooting D103176X012 June 2017 Checking Voltage Available WARNING Personal injury or property damage caused by fire or explosion may occur it this test is attempted in any area which contains a potentially explosive atmosphere or has been classified as hazardous. To check the Voltage Available at the instrument, perform the following: 1.

  • Page 47: Technical Support Checklist

    Instruction Manual Maintenance and Troubleshooting D103176X012 June 2017 Technical Support Checklist Have the following information available prior to contacting your Emerson sales office or Local Business Partner for support. 1. Instrument serial number as read from nameplate ________________________________________________ 2. Is the digital valve controller responding to the control signal? Yes _________ No _________ If not, describe: 3.
  • Page 48 Instruction Manual Maintenance and Troubleshooting D103176X012 June 2017 Mounting 1. Actuator application: Sliding Stem? _______ Rotary? _______ 2. What Make, Brand, Style, Size, etc. actuator is the DVC2000 mounted on? ________________________ 3. What is the Mounting Kit part number? _________________________________________________________ 4.

  • Page 49: Section 5 Parts

    Use only genuine Fisher replacement parts. Components that are not supplied by Emerson Automation Solutions should not, under any circumstances, be used in any Fisher instrument. Use of components not supplied by Emerson Automation Solutions may void your warranty, might adversely affect the performance of the valve, and could cause personal injury and property damage.

  • Page 50: Parts List

    Instruction Manual Parts D103176X012 June 2017 Description Part Number Parts List (refer to figures 5‐1, 5‐2 and 5‐3) Feedback Array Kit (cont'd) Rotary  [Kit contains feedback assembly, pointer assembly, travel  indicator scale and M3 machine pan head screws qty. 2]. Note  Stainless steel kits only for use with stainless steel mounting kits.
  • Page 51 Instruction Manual Parts D103176X012 June 2017 Figure 5‐1. FIELDVUE DVC2000 Digital Valve Controller Assembly, Housing A APPLY LUBRICANT/SEALANT NOTE: VIEW A 1. APPLY LUBRICANT KEY 65 TO ALL O-RINGS UNLESS OTHERWISE SPECIFIED PIPE AWAY VENT GE13174-F, SHEET 1 OF 3...
  • Page 52 Instruction Manual Parts June 2017 D103176X012 Figure 5‐2. FIELDVUE DVC2000 Digital Valve Controller Assembly, Housing A APPLY LUBRICANT/SEALANT NOTE: 1. APPLY LUBRICANT KEY 65 TO ALL O-RINGS UNLESS OTHERWISE SPECIFIED GE13174-F, SHEET 2 OF 3...
  • Page 53 Instruction Manual Parts D103176X012 June 2017 Figure 5‐3. FIELDVUE DVC2000 Digital Valve Controller Assembly, Housing A VIEW B VIEW B POSITIONER WITH POSITIONER ONLY TRANSMITTER AND LIMIT SWITCHES VIEW B APPLY LUBRICANT/SEALANT NOTE: 1. APPLY LUBRICANT KEY 65 TO ALL O-RINGS UNLESS OTHERWISE SPECIFIED...
  • Page 54 Instruction Manual Parts June 2017 D103176X012...

  • Page 55: Appendix A Principle Of Operation

    The way in which the DVC2000 accomplishes this is through a two-stage positioner design. Refer to figure A‐1 for a block diagram of the positioner operation. Figure A‐1. FIELDVUE DVC2000 Digital Valve Controller Block Diagram NON-CONTACT POSITION FEEDBACK...
  • Page 56 Instruction Manual Principle of Operation June 2017 D103176X012 D The I/P converter assembly is connected to supply pressure and converts the drive signal into a pressure signal. The I/P converter is the pre-amplifier stage in the two-stage positioner design. This component enables high static gain for responsiveness to small changes in the input signal.

  • Page 57: Appendix B Local Interface Flow Chart And Field Communicator Menu Trees

    Instruction Manual Local Interface Flow Chart/Menu Trees D103176X012 June 2017 Appendix B Local Interface Flow Chart and Field Communicator Menu Trees B‐B‐ This section contains the Local Interface Flow Chart and the Field Communicator menu trees for instrument level HC, AD, and PD and instrument level AC.
  • Page 58 Instruction Manual Local Interface Flow Chart/Menu Trees June 2017 D103176X012 Local Interface Flow Chart These items are identified by an alert icon on the default screen Home Screen TRAVEL = 66.8% TRAVEL CHECK SHUTDOWN CHECK CHECK I/P 14.6 MA 0.92 BAR DEVIATION MOUNTING CONVERTER...
  • Page 59 Instruction Manual Local Interface Flow Chart/Menu Trees D103176X012 June 2017 Only when transmitter / limit switch hardware is installed REPLACE MAIN SWITCH1 = OPEN PROTECTION FW3:1, HW1:2 " OFF BOARD SWITCH 2 = CLOSED TUNING = C QUICK SETUP COMPLETE Y + B INVERT DISPLAY 180_ Note: Hold Y + B...

  • Page 60: Hart Tag

    Instruction Manual Local Interface Flow Chart/Menu Trees June 2017 D103176X012 Field Communicator Fast‐Key Sequence (Instrument Level HC, AD and PD) Fast-Key Fast‐Key Function/Variable Coordinates Function/Variable Coordinates Sequence Sequence Actuator Style 1-2-5-2 Polling Address 1-2-3-7 Alert Record 1-2-7-6 Pressure Analog Input Pressure Calibration 1-4-4 Analog Input Calibration...

  • Page 61: Hart Tag

    Instruction Manual Local Interface Flow Chart/Menu Trees D103176X012 June 2017 Field Communicator Menu Tree for Instrument Level HC, AD and PD Hot Key 1 Instrument Mode 2 Protection 1 Tuning Set 1‐1‐1‐4 Tuning 3 Tuning 2 Damping Factor 3 Expert Tuning Gains 1 Tuning Set 1‐1‐1 2 Damping Factor 1‐1‐1‐4‐3...

  • Page 62: Hart Tag

    Instruction Manual Local Interface Flow Chart/Menu Trees June 2017 D103176X012 Field Communicator Fast‐Key Sequence (Instrument Level AC) Fast‐Key Fast‐Key Function/Variable Coordinates Function/Variable Coordinates Sequence Sequence Analog Input Calibration 1‐3‐1 Integral Gain 1‐2‐3‐6‐2 Analog Input Units 1‐2‐2‐1 Integral Settings 1‐2‐3‐6 Auto Calibrate Travel 1‐3‐2 LUI Language 1‐2‐1‐8...

  • Page 63: Hart Tag

    Instruction Manual Local Interface Flow Chart/Menu Trees D103176X012 June 2017 Field Communicator Menu Tree for Instrument Level AC Hot Key 1 Instrument Mode 1 Tuning Set 2 Protection 2 Damping Factor 1 Prop Gain 3 Tuning 3 Expert Tuning Gains 2 Vel Gain 3 MLFB Gain 1‐1‐1 Auto Setup 1‐1‐1‐4...
  • Page 64 Instruction Manual Local Interface Flow Chart/Menu Trees June 2017 D103176X012...

  • Page 65: Glossary

    Instruction Manual Glossary D103176X012 June 2017 Glossary Alert Point Calibration Location An adjustable value that, when exceeded, Where the instrument was last calibrated; either activates an alert. in the factory or in the field. Configuration Algorithm Stored instructions and operating parameters for A set of logical steps to solve a problem or a FIELDVUE Instrument.
  • Page 66 Instruction Manual Glossary June 2017 D103176X012 Controller Deviation A device that operates automatically to regulate a Usually, the difference between set point and controlled variable. process variable. More generally, any departure from a desired or expected value or pattern. Current‐to‐Pressure (I/P) Converter Device ID An electronic component or device that converts a milliamp signal to a proportional pneumatic...
  • Page 67 See table 3‐1. The ratio of output change to input change. Hardware Revision Instrument Mode Revision number of the Fisher instrument Determines if the instrument responds to its hardware. The physical components of the analog input signal. There are two instrument instrument are defined as the hardware.

  • Page 68: Instrument Serial Number

    Instruction Manual Glossary June 2017 D103176X012 Instrument Protection Menu Determines if commands from a HART device can A list of programs, commands, or other activities calibrate and/or configure certain parameters in that you select by using the arrow keys to the instrument.
  • Page 69 Instruction Manual Glossary D103176X012 June 2017 Pressure Sensor Seat Load A FIELDVUE instrument internal device that Force exerted on the valve seat, typically senses pneumatic pressure. DVC2000 digital expressed in pounds force per lineal inch of port valve controllers have one actuator pressure circumference.
  • Page 70 Instruction Manual Glossary June 2017 D103176X012 Travel Accumulator Alert Travel Alert Low Point Checks the difference between the Travel Value of the travel, in percent of ranged travel, Accumulator value and the Travel Accumulator which, when exceeded, sets the Travel Alert Lo Alert Point.
  • Page 71 Instruction Manual Glossary D103176X012 June 2017 Travel Limit Tuning Set A setup parameter that defines the maximum Preset values that identify gain settings for a allowable travel (in percent of ranged travel) for FIELDVUE instrument. The tuning set and supply the valve.
  • Page 72 Instruction Manual Glossary June 2017 D103176X012...

  • Page 73: Index

    Instruction Manual Index D103176X012 June 2017 Index Analog Input Units, 15 ATEX, Hazardous Area Classification, 5 AC (Auto Calibrate), 4, 34 Auto Calibrate (AC), 4, 34 Actuator and Valve Information, 16 Auto Calibrate Travel, 28 Actuator Information, for Setup, 12 auto tuner, 26 AD (Advanced Diagnostics), 4, 34 Advanced Diagnostics (AD), 4, 34...

  • Page 74: Hart Tag

    Instruction Manual Index June 2017 D103176X012 Cycle Counter Displaying Value, 33 Enabling Alert, 22 Factory Default Settings, Detailed Setup Parameters, Resetting, 23 Cycle Counter Alert, 22, 35 Failure Alerts, 36 Drive Current Fail, 36 Cycle Counter Alert Enable, 22 Flash ROM Fail, 36 Cycle Counter Alert Point, 22 NVM Fail, 36 Offline/Failed, 36...
  • Page 75 Instruction Manual Index D103176X012 June 2017 INMETRO, Brazil, Certification, 6 LUI Pressure Units, 15 Input Characteristic, 17 Input Impedance, 5 Input Range High, 15 Magnet Assembly, 4 Input Range Low, 15 Magnetic Feedback Assembly, Replacing, 41 Input Signal, 5, 55 Analog Input Signal, 5 Main Electronics Revision, 34 Maximum Voltage, 5...
  • Page 76 Instruction Manual Index June 2017 D103176X012 Restart Control Mode, 10 Restarting the Instrument, 10 Parameters Reverse Polarity Protection, 5 conditions for modifying, 13 Factory Default, 11 Revision Information Device, 34 Parts Firmware, 34 Kits, 49 HART Universal, 34 Ordering, 49 Main Electronics, 34 PD (Performance Diagnostics), 4, 34 Secondary Electronics, 34...
  • Page 77 Instruction Manual Index D103176X012 June 2017 Transmitter, 6, 25 Tvl Lim/Cutoff Low, 35 Fault Indication, 6 Reference Accuracy, 6 Supply Voltage, 6 Transmitter Action, 25 Transmitter/Switches, 25 Travel, 33 Displaying Value, 33 Valve Alerts, 35 Alert Record has Entries, 35 Travel Accumulator Alert Record is Full, 35 Displaying Value, 34...
  • Page 78 Instruction Manual Index June 2017 D103176X012...
  • Page 79 Instruction Manual Digital Valve Controller D103176X012 June 2017...
  • Page 80 Responsibility for proper selection, use, and maintenance of any product remains solely with the purchaser and end user. Fisher, FIELDVUE, ValveLink, Tri-Loop, Rosemount are marks owned by one of the companies in the Emerson Automation Solutions business unit of Emerson Electric Co.

Table of Contents

Save PDF