This book has important information for the use and safe operation of this machine. Failure to read this book prior to operating or attempting any service or maintenance procedure to your American Sanders machine could result in injury to you or to other personnel; damage to the machine or to other property could occur as well. You must have training in the operation of this machine before using it.
Page 3
DANGER: Failure to read the Owner’s Manual prior to operating or servicing your American Sanders machine could result in injury to you or to other personnel; damage to the machine or to other property could occur as well. You must have training in the operation of this machine before using it.
Introduction The Sander 1600DC The Sander 1600DC is a floor sanding machine. It can also be used for polishing, spraying, buffing and stripping. The machine can be used on wood, vinyl, terrazzo or cement floors. Machine Specifications Model Sander 1600DC...
Electrical Connection Instructions 120 VOLT MACHINES Instructions for connection to the power supply and the electrical ground. This product must be grounded. If it should malfunction or breakdown, grounding provides a path of least resistance for electric current to reduce the risk of electrical shock.
Machine Set-up WARNING: Always remove the electrical plug from the electrical outlet before installing or changing the sandpaper. How To Install The Sandpaper To install the sandpaper, follow this procedure: Put the handle in the vertical position. Lock the handle. To lock the handle, push the locking lever down.
Page 9
Machine Set-up WARNING: Always remove the electrical plug from the electrical outlet before installing or changing the pad or brush. How To Install The Brush Or Pad Driver To install the brush or pad driver, follow this procedure: Put the handle in the vertical position. To lock the handle, push the locking lever down.See figure 4.
Page 10
Machine Set-up How to Install the Dust Control Skirt To install the skirt, follow this procedure: Wrap the skirt around the bumper such that the draw string can be inserted into the recess of the bumper. See figure 7. Orient the brush fastening strap at the rear of the machine to prevent scratching surfaces.
Operating Instructions WARNING: Never start machine when the handle is in the vertical position. The switch to start and stop the machine is activated by the interlock switch (Fig. 10) and the levers (Fig 10A) under the handle grips. To start the machine, follow this procedure: Figure 10 1.
Induction type motors do not require motor brushes. If repairs to the gear unit or motor are needed, do not disassemble the gears and motor. Return the machine to the nearest American Sanders Service Branch or American Sanders Authorized Service Center.
Page 13
Este manual contiene información importante acerca del uso y la seguridad de la máquina. Si no lee el manual antes de utilizar su máquina American Sanders o de intentar realizar los procedimientos de reparación o mantenimiento de la misma, usted o el resto del personal podrían sufrir lesiones;...
Instrucciones De Seguridad Para El Operador PELIGRO significa: Usted u otras personas pueden estar expuestos a sufrir lesiones personales, inclusive la muerte si las indicaciones de PELIGRO que se encuentran en esta máquina o en el manual de instrucciones se ignoran o no se tienen en cuenta. Lea y respete todas las indicaciones de PELIGRO que se encuentran en el manual de instrucciones y en la máquina.
PRESENTACION DE LA MAQUINA PRESENTACION DE LA MAQUINA Sander 1600DC Sander 1600DC es una máquina para pulir pisos. También puede ser utilizada para lustrar, pulverizar, sacar brillo y decapar. La máquina puede ser utilizada en pisos de madera, vinilo, terrazzo o cemento. Modelo Sander 1600DC Número de código...
INSTRUCCIONES PARA LA CONEXION ELECTRICA DE LA MAQUINA Toma cor- riente con polo de tierra. Tapa del toma cor- riente con Terminal polo de de tierra tierra. Figura 9...
PREPARACION DE LA MAQUINA PARA TRABAJAR ADVERTENCIA: Antes de instalar o cambiar el papel abrasivo, desconecte siempre el enchufe de la toma de corriente. Cómo instalar el papel abrasivo Instale el papel abrasivo, siguiendo las siguientes instruccions: Ponga el mango en posición vertical. Bloquee el mango presionando hacia abajo la palanca de bloqueo.
PREPARACION DE LA MAQUINA PARA TRABAJAR AVISO: Desconecte siempre el enchufe de la caja de enchufe conectada con la red antes de instalar o cambiar el disco o el cepillo. Cómo instalar el cepillo o el portadisco Para instalar una cabeza de cepillo o un portadisco, sigue este procedimiento : Coloque la tobera en posición vertical.
PREPARACION DE LA MAQUINA PARA TRABAJAR Cómo instalar la falda Para instalar la falda, siga este procedimiento: Envuelva la falda alrededor del parachoques de manera que la cadena de arrastre pueda ser insertada en el hueco del parachoques. Vea la figura 7. Oriente la correa de sujeción del cepillo ubicada en la parte posterior de la máquina para evitar rayar superficies.
FUNCIONAMIENTO DE LA MAQUINA Arranque y parada AVISO: Nunca arranque la maquina cuando la tobera está en posición vertical. El interruptor de arranque/parada se opera empujando el botón de cierre de seguridad (Véase Fig. 10) y usando las palancas (Véase Fig. 10A) situadas debajo del mango de mando. Para arrancar la máquina, siga este procedimiento : 1.
Para alargar la longevidad de la máquina y garantizar su funcionamiento óptimo, use sólo recambios American Sanders. NOTA: La grasa del sistema de accionamiento (503802) debe ser cambiada cada año. Los modelos 1600 y 1600DC necesitan 236 cm³ de grasa.
LISEZ CE MANUEL Ce Manuel contient des informations importantes concernant l’utilisation et le fonctionnement de cette machine dans des conditions de sécurité optimales. La non-lecture de ce manuel avant d’utiliser ou d’entretenir votre machine American Sanders risque de provoquer un accident ou d’endommager la machine ou son environnement. Vous devez avoir été formé...
Page 24
Consignes De Securite Destinees A L’operateur DANGER signifie: De graves blessures corporelles, voire la mort, peuvent survenir si les déclarations DANGER apposées sur l’appareil ou inscrites dans le Manuel de l’utilisateur sont ignorées ou ne sont pas suivies. Lisez et respectez toutes les consignes DANGER se trouvant dans le Manuel de l’utilisateur et sur l’appareil.
PRESENTATION DE LA MACHINE Sander 1600DC Sander 1600DC est un appareil de Sablage du sol. Il peut aussi être utilisé pour le polissage, le jet et le décapelage. La machine peut être utilisée sur le bois, vinyle, terrace ou sols cimentés.
Machines 120 V - Instructions Pour Le Raccordement Electrique Prise de courant avec mise à la terre Boîte de sortie Broche de mise mise à la à la terre. terre FIGURE 9...
Preparation De La Machine Avant La Mise En Service ATTENTION: Débrancer toujours la prise de la source d'alimentation électrique avant d'installer ou de changer le papier abrasif. Installation du papier abrasif Pour installer le papier abrasif, suivre la procédure suivante: Mettre la poignée en position verticale.
Preparation De La Machine Avant La Mise En Service AVERTISSEMENT: Débranchez toujours la fiche de la prise réseau avant d’installer ou de changer le disque ou la brosse. Comment installer la brosse ou le porte-disque Pour placer une tête de brosse ou un porte-disque, procéder comme suit: 1.
PREPARATION DE LA MACHINE AVANT LA MISE EN SERVICE Installation de la Jupe Pour installer la jupe, suivre la procédure suivante : Envelopper la jupe autour du pare-chocs afin que la ficelle de tirage puisse être insérée dans l’enfoncement du pare-chocs. Voir illustration 7.
MISE EN SERVICE DE LA MACHINE Mise en Marche et Arrêt AVERTISSEMENT: Ne jamais mettre la machine en marche lorsque le timon est en position verticale. L’interrupteur de marche/arrêt est activé par pression sur le bouton de verrouillage de sécurité (Voir fig. 10) et par les leviers (Voir fig.
Pour prolonger la vie de la machine et garantir son fonctionnement optimal, n'utilisez que des pièces de rechange American Sanders. NOTE : La graisse du système d'entraînement (503802) doit être changée chaque année. Les modèles 1600 et 1600DC il faut 236...
Page 37
Base Assembly Item Ref. No. Description 920342 Nut Esna 3/8-16 962892 Screw 1/4-20 Unc X 3/4 Pan Head 980349 Washer Wear Cam 980645 Washer, 3/8” S.A.E. Flat 56109699 Cam Assy With Grip 50793A Wheel 50986A Frame Main Sander 52348A Link Arm Right 52349A Link Arm Left 57120A...
NO OTHER WARRANTY, EXPRESSED OR IMPLIED, INCLUDING BUT NOT LIMITED TO ANY IMPLIED WARRANTY (1) The obligation of American Sanders under this warranty is limited OF MERCHANTABLILITY OR FITNESS FOR A PARTICULAR to repairing or replacing, at its option, any part which is proven to PURPOSE, IS MADE EXCEPT AS EXPRESSLY STATED HEREIN.
Need help?
Do you have a question about the 1600DC and is the answer not in the manual?
Questions and answers