Related Manuals for Reach ENC1200
Summary of Contents for Reach ENC1200
-
Page 1: User Manual
REACH HD Encoder ENC1200 User Manual V1.5 2012-01 Copyright © Shenzhen Reach IT Co., Ltd. - Page 2 Any part of this document, including the text, image and graph, is the property of Shenzhen Reach IT Co., Ltd. No part of this document shall be copied in any means without the prior written consent of Shenzhen Reach IT Co., Ltd. Reach reserves the right to revise this document without any prior notice.
- Page 3 This manual is subject to update from time to time without prior notice. If you come across any problem that cannot be solved according to the manual, please contact our technical department for solutions. Thank you. Copyright © Shenzhen Reach IT Co., Ltd. 3 / 16 ...
-
Page 4: Table Of Contents
...................... 1 3 ARAMETER SETTING 5.3 ........................ 1 4 YSTEM ETTING 5.4 ............ 1 5 ESTART THE ENCODER AND YNCHRONIZATION 5.5 ............................ 1 6 Copyright © Shenzhen Reach IT Co., Ltd. 4 / 16 ... -
Page 5: Product Overview
1. Product Overview 1.1 Product Introduction The HD Encoder is the special hardware equipment developed by Shenzhen Reach software Technology Co.,Ltd for HD video signal and VGA signal coding as well as network transmission. It supports 720P/1080i/1080P HD signals coding. This product adopts high-performance DSP chip and embedded operating system, and features high stability and reliability, high definition, low code rate and low delay. -
Page 6: Front Panel
2.3 Rear panel Figure: Rear Panel of HD Encoder ①Power Input ⑤Audio MIC In ②SDI Input ⑥Audio Line In ③DVI-I Input ⑦Network Interface ④Audio Line Out ⑧Serial Port RS232 Copyright © Shenzhen Reach IT Co., Ltd. 6 / 16 ... -
Page 7: Power On And Get Ip Address
IP address. Double click this program, select equipment you want to search, and click “Search” button, and then you can find the list of all the existing coders in the network, as shown in the following figure: Copyright © Shenzhen Reach IT Co., Ltd. 7 / 16 ... -
Page 8: Configuration And Management
HD Encoder and the PC with running DSSIpView.exe. 4. Configuration and Management 4.1 Software installation Find the EncoderManager software in the CD delivered together with the product, directly Copyright © Shenzhen Reach IT Co., Ltd. 8 / 16 ... -
Page 9: Connect To Encoder
IP is 192.168.120.12 and the model of the encoder is ENC1200/ENC1100. After the IP address and password are entered to the address field, press “OK”, and then you can preview the signal content of the HD encoder ENC-1200. -
Page 10: Parameter Settings
IP and gateway to the desired value in the “modify IP address” field. Click “OK” button and restart the HD encoder, and the new IP address will be effective. Copyright © Shenzhen Reach IT Co., Ltd. 10 / 16 ... - Page 11 Change password: passwords of common users and administrators can be changed for EncoderManager connecting to encoder. Mode selection: fixed code rate/fixed quality. The user can determine the mode and parameter value according to the actual use situation. Frame rate: 1-30 frames adjustable. Copyright © Shenzhen Reach IT Co., Ltd. 11 / 16 ...
-
Page 12: Web Configuration Management
(such as 192.168.110.11), Enter the user name and password (default: admin for both) and click “Login”, and then the system information of the HD encoder and other menu buttons will be displayed: Copyright © Shenzhen Reach IT Co., Ltd. 12 / 16 ... -
Page 13: Parameter Setting
In Quality Mode, a fixed quality is used for the transmission, while the bandwidth will be variable. User can flexibly select the transmission modes according to the network state. Copyright © Shenzhen Reach IT Co., Ltd. 13 / 16 ... -
Page 14: System Setting
You can set the coordinate position and content of the subtitles and select if the time is display as well. 5.3 System Setting Click “ Configure”, you may change the password of the admin user, upgrade the system and change the IP address of encoder. Copyright © Shenzhen Reach IT Co., Ltd. 14 / 16 ... -
Page 15: Restart The Encoder And Time Synchronization
“Modify”, the HD Encoder will restart automatically, and the new IP address will take effect after restart. 5.4 Restart the encoder and Time Synchronization Click the menu “RestartSys”, the following page will appear: Copyright © Shenzhen Reach IT Co., Ltd. 15 / 16 ... - Page 16 Restart Encoder: to remotely restart the server. 5.5 Exit Click the menu “exit”, the following page will appear: Click “Yes”: exit and close the WEB page; click “No”: cancel the exit operation. Copyright © Shenzhen Reach IT Co., Ltd. 16 / 16 ...