Slicer; Chorus - Roland RD-2000 Parameter Manual

Modulation FX Parameters
Parameter Value
OFF,
Feedback
RATE,
Knob DEPTH,
MOD WAVE
TRI,
SQR,
SIN,
SAW1,
SAW2
Mod Wave
SAW1
R
L
Rate
OFF, ON
(sync sw)
Rate (Hz) #/ 0.05–10.00
Rate (note) # note (p. 60)
Depth #
0–127
Low Gain
-15–+15
High Gain -15–+15
Level 0–127

25: SLICER

By applying successive cuts to the sound, this effect turns a
conventional sound into a sound that appears to be played as a
backing phrase. This is especially effective when applied to sustain-
type sounds.
L in
Slicer
R in
Slicer
Parameter Value
Switch
OFF, ON
Depth Knob
RATE,
ATTACK,
SHUFFLE
Rate Knob
OFF,
Feedback RATE,
Knob ATTACK,
SHUFFLE
Step 01–16
0–127
Rate
OFF, ON
(sync sw)
Rate (Hz) #/ 0.05–10.00
Rate (note) #
note (p. 60)
Attack # 0–127
44
Explanation
Specifies the parameter
that is controlled by the
MODULATION FX [FEEDBACK]
knob.
Modulation wave
TRI:
triangle wave
SQR: square wave
SIN:
sine wave
SAW1/2:
sawtooth wave
SAW2
R
L
If this is ON, the modulation
is synchronized to the tempo
of the rhythm (owner's
manual: p. 24).
[Hz]
Frequency of the change
Depth to which the effect is
applied
[dB] Gain of the low range
[dB] Gain of the high range
Output Level
L out
R out
Explanation
Turns the effect on/off.
Specifies the parameter
that is controlled by the
MODULATION FX [DEPTH]
knob.
Specifies the parameter
that is controlled by the
MODULATION FX [RATE]
knob.
Specifies the parameter
that is controlled by the
MODULATION FX [FEEDBACK]
knob.
Level at each step
If this is ON, the modulation
is synchronized to the tempo
of the rhythm (owner's
manual: p. 24).
[Hz]
Rate at which the 16-step
sequence will cycle
Speed at which the level
changes between steps
Parameter Value
Input Sync
OFF, ON
Sw
Input Sync
0–127
Threshold
LEGATO,
Mode
SLASH
Shuffle # 0–127
Level 0–127

26: CHORUS

This is a stereo chorus. A filter is provided so that you can adjust the
timbre of the chorus sound.
Balance D
L in
Chorus
Chorus
R in
Balance D
Parameter Value
Switch OFF, ON
Depth Knob
RATE,
BALANCE,
DEPTH
Rate Knob
OFF,
Feedback
RATE,
Knob BALANCE,
DEPTH
Explanation
Specifies whether an input
note will cause the sequence
to resume from the first step
of the sequence (ON) or not
(OFF)
Volume at which an input
note will be detected
Sets the manner in which the
volume changes as one step
progresses to the next.
LEGATO:
The change in
volume from one step's
level to the next remains
unaltered. If the level of a
following step is the same as
the one preceding it, there is
no change in volume.
SLASH: The level is
momentarily set to 0 before
progressing to the level of
the next step. This change
in volume occurs even if the
level of the following step is
the same as the preceding
step.
Timing of volume changes
in levels for even-numbered
steps (step 2, step 4, step 6...).
The higher the value, the
later the beat progresses.
Output level
2-Band
L out
EQ
Balance W
Balance W
2-Band
R out
EQ
Explanation
Turns the effect on/off.
Specifies the parameter
that is controlled by the
MODULATION FX [DEPTH]
knob.
Specifies the parameter
that is controlled by the
MODULATION FX [RATE]
knob.
Specifies the parameter
that is controlled by the
MODULATION FX [FEEDBACK]
knob.