Advertisement
conductor is connected to ground (earth) or to the
negative of the dc (battery) source.
Warning! Do not connect to ac wiring.
PROTECTIVE FEATURES OF
THE POWER INVERTER
Your appliance monitors the following potentially
hazardous conditions:
Low battery voltage. This condition is not harmful to
the appliance but could damage the power source. The
appliance automatically shuts down when input voltage
drops to 10,5 +/– 0,5 volts. When the condition is
corrected, turn the appliance off and then on.
Over voltage. The power inverter will automatically
shutdown when the input voltage exceeds 15,5 +/–
0,5V dc.
Short circuit. A reverse polarity or short circuit
condition may cause external or internal fuses to open
and may cause irreversible damage to the appliance.
Take extra care to insure a correct polarity connection.
Overload. The power inverter will automatically shut
down when the continuous load exceeds 500 watts.
When the overload is removed, reset the appliance by
turning it off and then on again.
Over temperature. If the temperature inside the
appliance is too high, the appliance will automatically
shut down. Allow the appliance to cool for at least
15 minutes before restarting after a heat-related
shutdown. Unplug the appliance while cooling.
HINTS FOR OPTIMUM USE
For best operating results, the inverter should be
placed on a flat and/or solid surface. The inverter
should only be used in locations that meet the
following criteria:
DRY: Do not allow water or other liquids to come into
contact with the inverter.
COOL: The surrounding air temperature should be
between 5°C and 40°C. Keep the inverter away from
direct sunlight, when possible.
WELL VENTILATED: Keep the area surrounding the
inverter clear to ensure free air circulation. Do not
place items on or over the inverter during operation.
The inverter will shut down if the internal temperature
gets too hot. Refer to the Protective features section of
this instruction manual for more information.
SAFE: Do not use the inverter near flammable
materials or in any location that may accumulate
flammable fumes or gases. This is an electrical
appliance that can briefly spark when electrical
connections are made or broken.
BDPC400AU_Manual_091216.indd 6-7
TROUBLESHOOTING
Common Audio/Visual Problems
Buzzing Sound In
Some inexpensive stereo
Audio Systems
systems make a buzzing
sound when operated from
an inverter because the power
supply in the electronic device
does not properly filter the
modified sine wave. The only
solution to this problem is to
use a sound system that has
a higher quality power supply.
Television
The inverter is shielded to
Interference
minimize interference with
television signals. However, in
some instances, interference
may still occur, particularly
where television signals
are weak. Try the following
corrective measures:
• Place the inverter as far as
possible from the television,
the aerial or cables. Use
an extension cable, if
necessary.
• Readjust the orientation of
the inverter, the aerial or
cables and the television
power cord to minimize
interference.
• Make sure the aerial or
cable feeding the television
provides an adequate
("snow free") signal and that
high quality, shielded aerial
or cable is used.
• Do not use the inverter
to operate high-power
appliances or tools at the
same time you are using it
to operate the television.
Common Power Output Problems
If the inverter on/
• Press the on/off switch to
off switch has been
turn the unit off.
pressed to turn the
• Check the dc connections.
unit on, but there
Tighten if necessary.
is no mains or
• Check the fuse in the dc
USB power output
vehicle power cord plug.
and the power/fault
Change if necessary.
LED is not lit:
• Press the on/off switch again
to turn the unit back on.
6
Common Power Output Problems
If the inverter on/
• Low battery voltage.
off switch has been
• Over voltage.
pressed to turn the
• Short circuit.
unit on, but there
• Overload.
is no mains or
• Over temperature.
USB power output
Press the on/off switch to
and the power/
turn the inverter off, correct
fault LED flashes,
the fault and then press the
then one of
on/off switch again to turn
the following
the inverter back on.
conditions has
occurred:
MAINTENANCE
From time to time wipe the outside casing of the
inverter with a damp cloth. Do not use any abrasive
or solvent-based cleaner. Do not immerse the inverter
in water.
Warning! Before performing any maintenance or
cleaning on the inverter, disconnect it from any power
source.
Replacing the fuse in the dc power
cord plug
• Remove the grooved cap by turning it counter
clockwise.
• Remove the rubber washer, centre pin and the
spring.
• Remove the fuse.
• Fit a new fuse of the same type and size (12A/250V).
• Install the centre pin, spring and rubber washer.
• Install the grooved cap by turning it clockwise onto
the plug.
PROTECTING THE ENVIRONMENT
Correct disposal of this product
This marking indicates that this product
should not be disposed with other
household waste throughout the EU. To
prevent possible harm to the environment
or human health from uncontrolled
waste disposal, recycle it responsibly to promote the
sustainable reuse of material resources. To return
your used device, please use the return and collection
systems or contact the retailer where the product
was purchased. They can take this product for
environmentally safe recycling.
Separate collection of used products and packaging
allows materials to be recycled and used again.
Re-use of recycled materials helps prevent
environmental pollution and reduces the
demand for raw materials.
Local regulations may provide for separate collection
of electrical products from the household, at municipal
waste sites or by the retailer when you purchase a
new product.
TECHNICAL DATA
Input voltage:
12,5V dc, 48A
Output voltage:
230-240V ac, 50 Hz
Power output:
500W continuous
USB:
5V dc, 500mA
Output waveform:
Modified sine wave
Dc plug fuse:
12A/250V
WARRANTY
Our goods come with guarantees that cannot be
excluded under the Australian & New Zealand
Consumer Law. You are entitled to a replacement
or refund for a major failure and compensation
for any other reasonably foreseeable loss or
damage. You are also entitled to have the goods
repaired or replaced if the goods fail to be of
acceptable quality and the failure does not
amount to a major failure.
Baccus Worldwide LLC is confident of the quality of
its products and offers an outstanding warranty. This
warranty statement is in addition to and in no way
prejudices your statutory rights under the Australian &
New Zealand Consumer Law.
If a Baccus Worldwide LLC product becomes
defective due to faulty materials, workmanship or
lack of conformity, within 24 months from the date
of purchase, Baccus Worldwide LLC guarantees to
replace defective parts, repair products subjected to
fair wear and tear or replace such products to make
sure of the minimum inconvenience to the customer
unless:
• The product has been used for trade, professional or
hire purposes;
• The product has been subjected to misuse or
neglect;
• The product has sustained damage through foreign
objects, substances or accidents;
• Repairs have been attempted by persons other than
Baccus Worldwide LLC service staff.
To claim on this warranty, you will need to submit
proof of purchase and return the allegedly defective
product to Baccus Worldwide LLC's local market
distributor, at your expense.
Please visit our website www.baccusworldwide.com
to register your new Baccus Worldwide LLC product
and to be kept up to date on new products and special
offers. Further information on the Baccus Worldwide
LLC brand and our range of products is available at
www.baccusworldwide.com.
7
9/12/2016 11:55:46 AM
Advertisement
