Alternatively, wear a dis- tion, replace the picture tube only with one that charging Wrist-strap device. (Be sure to is the same type as the original. remove it prior to applying power--this is an electric shock precaution.) Samsung Electronics...
Page 3
17. Observe the original lead dress, especially near the following areas : Antenna wiring, sharp edges, and especially the AC and high voltage power supplies. Always inspect for pinched, out-of-place, or frayed wiring. Do not change the spacing between components and the Samsung Electronics...
(Except for Lithium Ion Battery Pack and tape) Built-in MIC Omni-directional stereo condenser microphone Remote Control Indoors: greater than 49ft (15m) (straight line), Outdoors: greater than 16.4ft (5m) (straight line) The technical specifications and design may be changed without notice. Samsung Electronics...
Page 5
DC 8.4V, Lithium Ion Battery Pack 7.4V Power source type Lithium Ion Battery Pack, Power supply (100V~240V) 50/60Hz Power consumption (Recording) 4.9W(LCD), 3.7W(LCD Back Light off mode; VP-D530/D530i/D590/D590i only), 3.7W(CVF) Operating temperature 0˚~40˚C (32˚F~104˚F) Storage temperature -20˚C ~ 60˚C (-4˚F ~ 140˚F) External dimension VP-D530/D530i/D530T/D530Ti: Length 93.3mm, Height 95mm, Width 40.6mm...
Page 10
Disassembly and Reassembly 3-1-5 Ass’y CVF Removal 3 Remove 1 screw 4 Remove 3 screws 1 Remove 1 screw 5 Remove Ass’y CVF in the direction of arrow. 2 Remove Front PCB Fig. 3-5 Ass’y CVF Removal Samsung Electronics Samsung Electronics...
Page 11
Disassembly and Reassembly 3-1-6 Ass’y CAMERA Removal 2 Remove Ass’y CAMERA in the direction of arrow. 1 Remove 1 screw Fig. 3-6 Ass’y CAMERA Removal Samsung Electronics...
DSC ADJ 6. After setting adjustment value, please push the LCD/CVF ADJ “MENU SELECTOR” to confirm DATA. DSC F/WRITE –:– –:– –:– – VCR ADJ Indicates current adjustment item. EPR:FF EVR:FF Indicates the adjusted values Indicates preset values Samsung Electronics...
Page 15
EASY CUSTOM MENU SELECTOR STOP STEP 3 . If you want to finish the adjustment mode, you have to do Power Reset. The Power Reset means that you pull out the power source and pull in it again. Samsung Electronics...
Page 16
COLOR LEVEL (FIX) AGC-MARK ACC-MARK S-AGC-MARK-OFFSET S-ACC-MARK-OFFSET LCD COLOR OFFSET DIF INITIAL MODEL DATA 1 MODEL Adj. Value MODEL Adj. Value VP-D530/D530T VP-D530i/D530Ti MODEL DATA 1 – VP-D590/D590T VP-D590i/D590Ti SCD530/D530T SCD590/D590T MODEL DATA 2 MODEL Adj. Value MODEL DATA 2 –...
Page 17
2) Press the "push the MENU SELECTOR" when storing confirmed adjustment value of each adjustment step in EEPROM. 3) The OSD shows “OK” after finishing each adjustment step. 4) To clear the adjustment mode, pull out the power source. Samsung Electronics...
Page 18
“MENU SELEC- TOR” to confirm DATA. Note : "XX" indicates variable values. STEP 3 CAMERA ADJ Monitor OSD shows " ". EPR : FF EVR : FF Then camera adjustment mode has been activated successfully. Samsung Electronics...
Page 20
CRCB_WB_HI VALUE AT FLASH ON(#166) PERCENT FROM IRIS OUTPUT VALUE AT FLASH ON CBWB VALUE AT FLASH ON (#168) AF OPTION 1 SPOT OPTION1 AF_OPTION2 AF_OPTION3 ZOOM TRACK MIDDLE,WIDE 0.5STEP SHIFT 0.5step m/w shift(d3:1) AF_OPTION4 m/f 0(#69,#70) AF_OPTION5 Samsung Electronics...
Page 21
AWB_B_5100_MOVE TO CENTER AWB_R_5100_MOVE TO CENTER R MAPPING ,WHEN 3100_R < WB_IN_R_DATA < 2600_R R_3100_OVER WHEN IN_DATA > 3100_B B_3100_OVER WHEN IN_DATA > 3100_B AWB_OPTION[D70-D5] WB_RIGHT AREA _DIVIDE SCALE WB_LEFT AREA _DIVIDE SCALE TRACKING DICISION OUTDOOR HALL @ R_GAIN_POSI_5100 Samsung Electronics...
Page 22
Hallgain Start At Hall Adjust [CHANGED BY HALL-ADJ#0CD]Hall Min Value( Iris Close ) [CHANGED BY HALL-ADJ#0CD]Hall Max Value( Iris Open ) LENS_CHECK_LIMIT_0 LENS_CHECK_LIMIT_1 LENS_CHECK_LIMIT_2 LENS_CHECK_LIMIT_3 LENS_CHECK_LIMIT_4 NO USED Ae Control Value At Adjt Agc Min Limit Value Agc Max Limit Value Samsung Electronics...
Page 23
NO_USED NO_USED LENS_AUTO_ADJUST_3M FOR SERVICE FIELD CAMERA INITIAL ‘AA’+CONFIRM GYRO_CHECK_CENTER_VALUE GYRO_CHECK_THRESHOLD_VALUE camera model code(line-initial) agc middle point set (#0B5~ #1DA ~#0E3) agc middle chroma suppress. Percent of #142 agc middle noise slice (#133) agc middle YH-APT-GAIN+ (max:1F)(#131) 4-10 Samsung Electronics...
Page 28
D/ZOOM DOWN END POINT [ldz]D/Z_OFFE_WIDE_H [d/z]D/Z00M MAX STEP [d/z]_HSIZE(#11D) [d/z]_VSIZE(#11E) WIDE P_OFFSET CONTROL VALUE NEW IRIS CONTROL CENTER VALUE AT IRIS ADJT DSE_ART_#143 DSE_SEPIA_R_#163 DSE_SEPIA_C_RY_HP_#172 DSE_B/W_H1/H2_DLY_#102 DSE_B/W_SHP/SHD_DLY_#103 DSE_B/W_ADCLK/RG_DYL_#104 DSP_YART_EMBO_#143 DSP_YH_PST_EMBO_GAIN_EMBO_#144 DSP_EMBO_OFFSET_EMBO_#146 DSP_DSE_Y_V_APT_BKTH_EMBO_#150 DSP_DSE_Y_H_APT_GAIN_POSI_EMBO_#151 DSP_DSE_Y_H_APT_GAIN_NEGAI_EMBO_#152 DSP_DSE_Y_V_APT_GAIN_POSI_EMBO_#153 DSP_DSE_Y_V_APT_GAIN_NEGA_EMBO_#154 DSP_DSE_Y_APT_NOISE_SLICE_EMBO_#155 DSP_DSE_Y_APT_CLIP_EMBO_#156 DSP_DSE_YHILIGHT_GAIN_EMBO_#157 DSP_DSE_YAPT_NSLICEAFTE_GAM_EMBO_#158 Samsung Electronics 4-15...
Page 29
COLOR_BAR_PATTERN_GEN FOR LCD(CVF)_ADJUST_#160 COLOR_BAR_PATTERN_GEN FOR LCD(CVF)_ADJUST_#170 COLOR_BAR_PATTERN_GEN FOR LCD(CVF)_ADJUST_#171 COLOR_BAR_PATTERN_GEN FOR LCD(CVF)_ADJUST_#172 COLOR_BAR_PATTERN_GEN FOR LCD(CVF)_ADJUST_#173 COLOR_BAR_PATTERN_GEN FOR LCD(CVF)_ADJUST_#174 COLOR_BAR_PATTERN_GEN FOR LCD(CVF)_ADJUST_#175 COLOR_BAR_PATTERN_GEN FOR LCD(CVF)_ADJUST_#176 COLOR_BAR_PATTERN_GEN FOR LCD(CVF)_ADJUST_#177 COLOR_BAR_PATTERN_GEN FOR LCD(CVF)_ADJUST_#167 COLOR_BAR_PATTERN_GEN FOR LCD(CVF)_ADJUST_#168 COLOR_BAR_PATTERN_GEN FOR LCD(CVF)_ADJUST_#169 REVISION_DATE 4-16 Samsung Electronics...
Page 30
3) Press the EASY(Mode Up)/CUSTOM(Mode Down) button so that OSD shows “OD6 XX XX”. 4) Press the MENU SELECTOR (Confirm) button. 5) Then Micom finds out Zoom VR center position. Store Zoom VR center value in OB7. 3m +/-1Cm Samsung Electronics 4-17...
Page 31
5) Press the MENU SELECTOR (Confirm) button 6) The OSD shows “OK” after finishing the to ensure that white spot on a vectorscope is adjustment. moving in the middle of screen. 6) The OSD shows “OK” after finishing the adjustment. 4-18 Samsung Electronics...
Page 32
5) Press the MENU SELECTOR UP (Data that the red level is a Up)/MENU SELECTOR DOWN (Data Down) SCD530/D530T/D590/D590T: 70IRE, so that the red level is VP-D530/D530i/D590/D590i/ SCD530/D530T/D590/D590T: 65IRE, D530T/D530Ti/D590T/D590Ti: 500mV. VP-D530/D530i/D590/D590i/ 6) Press the MENU SELECTOR (Confirm) button D530T/D530Ti/D590T/D590Ti: 480mV.
Page 33
5) Press the MENU SELECTOR UP (Data Up)/ that the cyan level is MENU SELECTOR DOWN (Data Down) so SCD530/D530T/D590/D590T: 65IRE, that the cyan level is VP-D530/D530i/D590/D590i/ SCD530/D530T/D590/D590T: 60IRE, D530T/D530Ti/D590T/D590Ti: 450mV. VP-D530/D530i/D590/D590i/ 6) Press the MENU SELECTOR (Confirm) button D530T/D530Ti/D590T/D590Ti: 400mV.
Page 34
5) Press the MENU SELECTOR UP (Data Up)/ 45IRE 50IRE MENU SELECTOR DOWN (Data Down) so that the blue level is SCD530/D530T/ D590/D590T: 50IRE, VP-D530/D530i/D590/ D590i/D530T/D530Ti/D590T/D590Ti: 350mV. 10. B-Y NEGATIVE GAIN (indoor) 6) Press the MENU SELECTOR (Confirm) button to store data.
Page 35
1500-2000 Lux. 5) Press the MENU SELECTOR UP (Data Up)/ MENU SELECTOR DOWN (Data Down) so that the yellow level is SCD530/D530T/ D590/D590T: 45IRE, VP-D530/D530i/D590/ 11-b. R-Y POSITIVE HUE (outdoor) D590i/D530T/D530Ti/D590T/D590Ti: 300mV. 1) Camera mode & 5100˚ K color bar chart 6) Press the MENU SELECTOR (Confirm) button (3100°K color bar chart + C16 filter)
Page 36
1500-2000 Lux. 5) Press the MENU SELECTOR UP (Data Up)/ BLUE VECTOR MENU SELECTOR DOWN (Data Down) so 345 DEG that the cyan vector is 280˚ . 6) Press the MENU SELECTOR (Confirm) button to store data. Samsung Electronics 4-23...
Page 37
YELLOW VECTOR color bar chart precisely and the illumination is 168 DEG 165 DEG 1500-2000 Lux. 5) Press the MENU SELECTOR UP (Data Up)/ MENU SELECTOR DOWN (Data Down) so that the yellow vector is 168˚ . 4-24 Samsung Electronics...
Page 38
Shift adjustment address to right. CUSTOM (Mode Down) Up value. MENU SELECTOR UP (Data Up) MENU SELECTOR DOWN (Data Down) Down value. Note: In service adjustment mode, button names are different from those in customer function control mode. Samsung Electronics 4-25...
Page 39
B3(Adjust) C2(Adjust) B3(Adjust) C2(Adjust) 81(Adjust) 81(Adjust) 88(Adjust) 88(Adjust) 4. How to adjust CL135 USR BRT AT LCD ADJUST SHORT VCO ADJUST CONTRAST TRANS S.BRT R S.BRT B ICL01 S.CONT R S.CONT B B/L CONN LCD CONN 4-26 4-26 Samsung Electronics...
Page 40
Transmission : 4.2 V ± 0.05 V TRANS-Reflective : 4.6 V ± 0.05 V (White DC Level) 5) Be sure to press the “MENU SELECTOR (CONFIRM)” push Button to Memorize Setting. 6) The OSD shows “OK”. Samsung Electronics 4-27 4-27...
Page 41
4) Adjust the MENU SELECTOR(DATA UP/ DATA DOWN) Button so that Pedestal Level is Transmission : 3.2 V ± 0.05 V TRANS-Reflective : 3.0 V ± 0.05 V (Pedestal DC Level) 5) Be sure to press the “MENU SELECTOR (CONFIRM)” push Button to Memorize Setting. 6) The OSD shows “OK”. 4-28 Samsung Electronics...
Page 42
4) Adjust the MENU SELECTOR(DATA UP/ DATA DOWN) Button so that White Level is Transmission : 4.2 V ± 0.05 V TRANS-Reflective : 4.6 V ± 0.05 V (White DC Level) 5) Be sure to press the “MENU SELECTOR (CONFIRM)” push Button to Memorize Setting. 6) The OSD shows “OK”. Samsung Electronics 4-29...
Page 43
: -50 mV ± 10 mV TRANS-Reflective : -50 mV ± 10 mV 5) Be sure to press the “MENU SELECTOR (CONFIRM)” push Button to Memorize Setting. 6) The OSD shows “OK”. V SYNC PART -50mV ± 10mV 4-30 Samsung Electronics...
Page 44
Shift adjustment address to right. CUSTOM (Mode Down) Up value. MENU SELECTOR UP (Data Up) Down value. MENU SELECTOR DOWN (Data Down) Note: In service adjustment mode, button names are different from those in customer function control mode. Samsung Electronics Samsung Electronics 4-31 4-31...
Page 45
MENU SELECTOR DOWN (Data down) so that Data is 55. ICV02 3) Press the MENU SELECTOR push (Confirm) to store Data. EEPROM 4) The OSD shows “INIT OK” after finishing the Adjustment. TO CVF Adjust Short (R, G, B waveform on each TP) 4-32 4-32 Samsung Electronics Samsung Electronics...
Page 47
Exploded View and Parts List Exploded View and Parts List 5-1 Ass’y Cabinet (1) (S.N.A) Samsung Electronics Samsung Electronics...
Page 48
Exploded View and Parts List Exploded View and Parts List Loc. No New Part No Description and Specification Remark AD97-04580C ASSY-MAIN BOARD;VP-D590 VP-D590 AD97-04580D ASSY-MAIN BOARD;VP-D590i VP-D590i AD97-04580A ASSY-MAIN BOARD;VP-D530 VP-D530 AD97-04580B ASSY-MAIN BOARD;VP-D530i/D530Ri VP-D530i/D530Ri ASSY-MAIN BOARD;SCD590 SCD590 AD97-04580E ASSY-MAIN BOARD;SCD530 SCD530 ASSY-MAIN BOARD;VM-B1900...
Page 49
Exploded View and Parts List Exploded View and Parts List 5-2 Ass’y Cabinet (2) 530 SERIES 1 6 3 (S.N.A) 590 SERIES Samsung Electronics Samsung Electronics...
Page 50
AD64-00824A WINDOW-REMOCON;PC VIOLET AD97-04851A ASSY-LINK BOTTOM;ASSY AD64-00814A CASE-RIGHT;Mg M/S EXP D/TITAN VP-D590/D590T/D590i/D590Ti/ SCD590/SCD590T AD64-00814B CASE-RIGHT;Mg NON-M/S EXP D/TITAN VP-D530/D530T/D530i/D530Ti/ SCD530/SCD530T AD64-00814C CASE-RIGHT;Mg M/S DOM D/TITAN VM-B1900/B1900T/B1700/B1700T AD64-00814D CASE-RIGHT;Mg NON-M/S DOM D/TITAN VM-B1300/B1300T AD64-00814E CASE-RIGHT;Mg NON-M/S EXP RED VP-D530Ri AD97-04959A ASSY-COVER JACK FRONT;INSERT...
Page 51
Exploded View and Parts List Exploded View and Parts List 5-3 Ass’y Cabinet (3) 1 9 3 (S.N.A) (S.N.A) Samsung Electronics Samsung Electronics...