Table of Contents
Advertisement
Quick Links
ORIGINAL MADE IN ITALY
ISTRUZIONI PER L'USO DELLA
IT
TAGLIERINA ELETTRICA
OPERATING INSTRUCTIONS
GB
TILE CUTTING MACHINE
MODE D'EMPLOI MACHINE
F
à DéCOUPER LES CARREAUX
BEDIENUNGSANLEITUNG
D
FLIESENSCHNEIDMASCHINE
MANUAL DE INSTRUCCIONES
E
MàqUINA PARA CORTAR BALDOSAS
BETjENINGSvEjLEDNING
DK
FLISESAvEMASkINE
DOkUMENTACjA TECHNICZNO-
PL
ruchowa Piła do cięcia Płytek
ИнструкцИя по эксплуатацИИ
RU
обрезной станок электрИческИй
KZ
AR
Advertisement
Table of Contents
Related Manuals for Battipav VIP 850
Summary of Contents for Battipav VIP 850
- Page 1 ORIGINAL MADE IN ITALY ISTRUZIONI PER L’USO DELLA TAGLIERINA ELETTRICA OPERATING INSTRUCTIONS TILE CUTTING MACHINE MODE D’EMPLOI MACHINE à DéCOUPER LES CARREAUX BEDIENUNGSANLEITUNG FLIESENSCHNEIDMASCHINE MANUAL DE INSTRUCCIONES MàqUINA PARA CORTAR BALDOSAS BETjENINGSvEjLEDNING FLISESAvEMASkINE DOkUMENTACjA TECHNICZNO- ruchowa Piła do cięcia Płytek ИнструкцИя...
- Page 2 Battipav srl DATI TECNICI - TEchNIcAL DATA - DONNéEs TEchNIquEs - TEchNIschE DATEN - DATOs TécNIcOs - TEkNIskE DATA - DANE TEchNIczNE - البيانات التقنية ART. 200 / 25,4 960x570x 450 mm. 318 x 318 mm. 40 mm. 40 mm.
- Page 3 SP845038 (245) SP850038 (260) SP855038 (290) (VITI e DADI PER TESTA MOTORE) (VITI e DADI PER TELAIO) (SCREWS AND NUTS FOR POWER PLANT) SP856038 (2110) (x1) (x1) (x1) (x1) (x1) (SCREWS AND NUTS FOR FRAME) SP850071 SP85060 SP81807/2 SP845001 (245) SP850001 (260) SP855001 (290)
- Page 4 Battipav srl DICHIARAZIONE CE EC DECLARATION DECLARATION CE DECLARACIÓN DE DI CONFORMITÁ oF coNForMity DE CONFORMITE kONFORMITÄTSER- CONFORMIDAD CE kLÄRUNG sottoscritto, undersigned, soussigné, Der Unterzeichner, der den abajo firmante, rappresentante representing the following représentant nachstehenden Hersteller representación de seguente costruttore manufacturer constructeur ci-aprés...
- Page 5 Battipav srl EF OvERENSSTEM- DEkLARACjA ДекларацИя сƏйкестІк CE إق ر ار MELSESERkLÆRING ZGODNOOCI WE соотВетстВИя ДекларацИясЫ للمطابقة Undertegnede, Niżej podpisany, Нижеподписавшийся Келесі конструктордың املوقع أدناه، الذي ميثل الرشكة املصنعة repræsenterer følgende reprezentujący firmę: представитель төмендегі қолқоюшы التالية fabrikant с л е д у ю щ е г о...
- Page 6 Battipav srl 1.5m...
- Page 7 Battipav srl...
-
Page 8: Purpose Of This Manual
Ensure that the piece to be cut is properly This manual is an integral part of the machine. supported by the tile clamp. It was produced by BATTIPAV S.R.L. to provide • Check before each cut that the adjustment knobs those authorised to work with the machine with the for the cutting angle are tightened. - Page 9 Battipav srl Store your tools in a save place Stay alert • When not in use, tools should be stored in dry and • Watch what you are doing. Use common sense. save places, out of the reach of children.
- Page 10 µF YEAR Ø max Ø int. Do not use sector discs Made by: BATTIPAV SRL Via Cavatorta, 6/1 Z.i. 2 - 48010 - Cotignola (RA) ITALY Tool diameter measurements Machine model IP Level Recovery tank water Year of...
-
Page 11: Machine Description
Battipav srl MACHINE DESCRIPTION INSTALLATION The VIP site cutter is a machine intended specifically TRANSPORT for cutting ceramics, single-fired items, terracotta, and marble (Max thickness 20 mm), up to a thickness The VIP machine is easy to carry by using the of 40 mm. - Page 12 Battipav srl In case of machine disassembly, perform the corresponds to that shown on the plate on the opposite operations. machine. • The machine must be connected to an effective earth wire. In case of doubt, do not connect the machine.
- Page 13 Battipav srl 3) DEvICE FOR DISCONNECTION FROM THE CUTTING A SURFACE AT 45° MAINS (PLUG): Machine power supply point. CAUTION During the maintenance phases, take out the device plug in order to disconnect the machine from the mains. Before positioning the motor head, make sure that: •...
-
Page 14: Residual Risks
Battipav srl RESIDUAL RISkS MAINTENANCE During the design phase, BATTIPAV SRL paid CAUTION particular CAUTION to the aspects that may generate risks for the safety and health of operators. In spite of this, there are still some potential risks, BeFore PerForMiNG aNy oPeratioN or... -
Page 15: Troubleshooting
Battipav srl Submersed pump DISPOSAL Polyamide When parts wear out or when the machine is finally Steel scrapped, waste disposal must be carried out in Aluminium compliance with the laws in force. Copper Epoxy Resin W.E.E.E. IT08020000002803 Electric Motor European...
Need help?
Do you have a question about the VIP 850 and is the answer not in the manual?
Questions and answers