Page 2
ö DT-600 & DRUM TRAINER START /STOP Instructions for use Features • Handle the unit with care. • Big LCD display. Easy-to-operate user- • Do not store or use the unit at locations friendly interface. that are subject to high humidity, dirt, or • Multiple metronome sounds. One group strong vibrations. of drum-set sounds. • Do not try to disassemble or repair the • Mixing function, allowing you to create unit yourself in the unlikely event that it original rhythm styles. does not work. • Loop play function, allows you to set your • Do not use solvents such as alcohol to own rhythm styles and to play them for a clean the unit. specified number of times. • Remove the battery from the unit when it • Memory function, to store user settings.
Rhythm level sliders Operating conditions In metronome mode: adjusts the volume of each rhythm. Always use the device in accordance with In rhythm edit mode: chooses the sound of each beat. these instructions. In loop mode: not active Notice Headphone jacks (6.35 mm and 3.5 mm ) To avoid the risk of damage do Master volume slider not subject the unit to any liquid or INPUT jack (6.35 mm) moisture. Do not expose the unit to MEMORY UP/DOWN jack (stereo) for pedal excessive heat. Keep the unit away to select memory locations from naked flames. START/STOP jack (mono) for pedal to start/ stop the metronome Components and functions Speaker Adjusts parameters or changes tempo Mounting nut ö [TAP] key to set the metronome tempo Power switch [START/STOP] button Tempo LED Starts or stops the metronome, loop play, or DC IN jack test run of a rhythm program.
BEAT: The values for TEMPO, rhythm, edit section. VOICE and BEAT are set using the BEAT 7. Press the [VOICE] button to change to the display. BEAT display. 8. When parameters are changed, "EDIT" will appear on the display. Press the [WRITE] button. "MEMORY" will flash. Press the [WRITE] button again. "MEMORY" will flash quickly. When it stops, the current param- eters are stored. If you want to exit the menu without storing the modified parameters, 2. Press the [TEMPO] button, "TEMPO" will press the [START/STOP] button after you flash. Rotate the [TEMPO/VALUE] dial to have pressed the [WRITE] button for the first adjust the value. Tempo range: 30 to 250 time. beats per minute. 3. The following four rhythms are available: Every rhythm corresponds to a master volume slider by means of which you can adjust the volume and edit the rhythm. 4. Press the [VOICE] button. "VOICE" will flash. Rotate the [TEMPO/VALUE] dial to select one timbre from the five choices. 5. Press the [BEAT/PATTERN] button, "BEAT" will flash. Rotate the [TEMPO/VALUE] dial to adjust the BEAT value. BEAT range: 1 – 8, 1+1 – 8+8. Press the [BEAT/PATTERN] button again to change to the PATTERN display. DT-600...
Loop mode Rhythm-edit mode Press one of the three [LOOP PROG], Press the [STYLE] or [RHYTHM SET] but- [LOOP SET] or [LOOP STYLE] buttons to ton to start the rhythm-edit mode from the start the loop mode from the metronome metronome mode or loop mode. mode or rhythm-edit mode. 1. Press the [STYLE] button, "STYLE" will flash. Use the [TEMPO/VALUE] dial to select the STYLE group to be edited (31 to 50 are user STYLE suggestions). 1. Press the [LOOP PROG] button, "LOOP PROG" will flash. Use the [TEMPO/VALUE] dial to select the loop group. Range: 1 to 16. 2. Press the [LOOPSET] button, "LOOP" will 2. Press the [RHYTHM SET] button, "BEAT" flash. Use the [TEMPO/VALUE] dial to set will flash. Use the [TEMPO/VALUE] dial to up how often the loop will be played. Range: select the time signature (1/4, 2/4, 3/4, 4/4). 0 to 99. 3. Press the [RHYTHM SET] button again, 3. Press the [LOOP STYLE] button. "STYLE" "RHYTHM SET" will flash. Use the [TEMPO/ will flash. Rotate the [TEMPO/VALUE] dial to VALUE] dial to select the rhythm pattern select the style. Range: 1 to 8. to be edited. The following five rhythms 4. Press the [MEMORY] button, "MEMORY" are available: . The sliders under will flash. Rotate the [TEMPO/VALUE] dial to...
29: CHA-CHA-CHA 19: REGGAE 30: MARCH STEP 3 20: CLAVE3-2 Close the battery cover • Tempo: 30 to 250 bpm • Loop group: 1 to 16 • Loop times: 0 to 99 • Loop styles: 1 to 8 • Dimensions (L × B × H): 160 × 120 × 36 mm • Weight: 310 g Delivery scope • Drum Trainer DT-600 • User manual • 9-V battery 6LR6 Power supply You can use either a DC-9-V power adapter or a 9-V battery. Before connecting check for correct polarity. To protect the environment and to increase battery life, use the 9-V DC adapter as often as possible. DT-600...
Disposal of the packaging material Disposal of your old device For the transport and This device is subject to protective packaging, the European directive environmentally friendly 2002/96/EC. materials have been At the end of its operating chosen that can be lifetime, do not dispose supplied to normal the device with your nor- recycling. mal household waste. Ensure that plastic bags, packaging, etc. are Dispose this device through an approved properly disposed and are not in the reach of waste disposal firm or through your local babies and young children. Choking hazard! waste facility. When discarding the unit, Do not just dipose these materials with your comply with the rules and regulations that normal household waste, but make sure that apply in your country. If in doubt, consult your they are fed to a recovery. Please follow the local waste disposal facility. notes and markings on the packaging. Batteries do contain some hazardous chemi- cals so they should not be thrown away with the normal household waste. They should be returned to the manufacturer for disposal or recycled elsewhere in accordance with your local regulations.
Need help?
Do you have a question about the DT-600 and is the answer not in the manual?
Questions and answers