Test Mode - Sony HCD-X1V Service Manual

HCD-X1V
AM STEP CHANGE (US and Canadian models)
The step interval of AM channels can be toggled between 9 kHz
and 10 kHz.
Procedure:
1. Press the button to turn on the system.
I/1
2. Press the [FUNCTION] button repeatedly to select the "TUNER
AM".
3. Press the button to turn off the system.
I/1
4. Press two buttons of [FUNCTION] and
system will turn on automatically. The message "AM 9k
STEP" or "AM10k STEP" appears on the fluorescent indicator
tube and thus the channel step is changed.
DVD VERSION VIEW
This mode is used to display the DVD version.
Procedure:
1. Press the button to turn on the system.
I/1
2. Press the [FUNCTION] button repeatedly to select the "DVD".
3. Press the button to turn off the system.
I/1
4. Press two buttons of and
x
will turn on automatically.
5. The DVD version appears on the TV screen.
COLD RESET
The cold reset clears all data including preset data stored in the
RAM to initial conditions.
Procedure:
1. Press the button to turn on the system.
I/1
, [FUNCTION] and
2. Press three buttons of
x
3. The message "COLD RESET" appears on the fluorescent
indicator tube, then becomes standby mode.
SHIP MODE
This mode moves the optical pick-up to the position durable to
vibration.
Procedure:
1. Press the button to turn on the system.
I/1
2. Press the [FUNCTION] button repeatedly to select the "DVD".
3. Press three buttons of
x
4. After the "STANDBY" blinking display finishes, the message
"MECHA LOCK" appears on the fluorescent indicator tube
and the ship mode is set.
PANEL TEST MODE
This mode is used to check the fluorescent indicator tube, LEDs,
keys, model, destination and software version.
Procedure:
1. Press three buttons of
x
2. LEDs (amber) and all segments in fluorescent indicator tube
are lighted up. And half LEDs (green) and segments in
fluorescent indicator tube are lighted up, all LEDs and others
half segments in fluorescent indicator tube are lighted up, then
LEDs (amber) and all segments in fluorescent indicator tube
are lighted up. This operation is repeated.
3. Press the button, the key check mode is activated.
N
4. In the key check mode, the fluorescent indicator tube displays
"K 0". Each time a button is pressed, "K 0" value increases.
However, once a button has been pressed, it is no longer taken
into account.
5. When you want to enter the software version display mode,
press the [VOLUME +] button. The model information appears
on the fluorescent indicator tube.
28
SECTION 5

TEST MODE

simultaneously. The
I/1
simultaneously. The system
I/1
simultaneously.
I/1
, and simultaneously.
Z
I/1
and [DISC 3] simultaneously.
,
N
6. Each time the [VOLUME +] button is pressed, the display
changes from destination information, MC version, GC
version, SYS version, DVD version, CDMA version, CDMB
version, ST version, TC version, TA version, DVD version,
TM version in this order, and returns to the model information
display.
7. When the [VOLUME --] button is pressed while the version
numbers are being displayed except model information and
destination information, the date of the software creation
appears. When the [VOLUME --] button is pressed again, the
display returns to the software version display. When the
[VOLUME +] button is pressed while the date of the software
creation is being displayed, the date of the software creation
is displayed in the same order of software version display.
8. To release from this mode, press three buttons in the same
manner as step 1 or disconnect the power cord.
AMP TEST MODE
Procedure:
1. Press three buttons of
x
message "MEASURE" appears on the fluorescent indicator
tube.
2. Press the [SLEEP] button on the remote commander. The
message "SAFETY" appears on the fluorescent indicator tube.
3. Press the [SLEEP] button on the remote commander again.
The message "MEASURE" appears on the fluorescent
indicator tube.
4. Press the [SOUND FIELD] button on the remote commander.
The message "SWAP FULL" appears on the fluorescent
indicator tube.
5. Each time the [SOUND FIELD] button is pressed, the display
changes from SWAP THRU, SWAP F2S, SWAP F2CW in
this order, and returns to "SWAP FULL" .
6. Press the [BASS/TREBLE] button on the remote commander.
The message "D.C.A.C. MIC" appears on the fluorescent
indicator tube.
7. Press the [BASS/TREBLE] button on the remote commander
again. The message "FUNC INPUT" appears on the
fluorescent indicator tube.
8. Press two buttons of [VOLUME +] and [VOLUME --] simultaneously.
The message "VOL N" (volume normal operation) or "VOL
M/M" (volume MIN/MAX operation) appears on the
fluorescent indicator tube and thus the volume step is changed.
9. When the [VOLUME --] button is pressed in the volume MIN/
MAX operation state, the message "VOLUME MIN" appears
on the fluorescent indicator tube.
10. When the [VOLUME +] button is pressed in the volume MIN/
MAX operation state, the message "VOLUME MAX" appears
on the fluorescent indicator tube.
11. To release from this mode, press
COLD RESET.
PRODUCT OUT
This mode moves the optical pick-up to the position durable to
vibration and clears all data including preset data stored in the RAM
to initial conditions.
Procedure:
1. Press the button to turn on the system.
I/1
2. Press the [FUNCTION] button repeatedly to select the "DVD".
3. Press three buttons of
simultaneously.
4. After the "STANDBY" blinking display finishes, The message
"MECHA LOCK" appears on the fluorescent indicator tube
and the ship mode is set.
, and simultaneously. The
N Z
button to execute the
I/1
, [DISC 3] and [VOLUME +]
x