Sony BVM-D14H1E Maintenance Manual page 17

Location and Function of Parts
BVM-D14H1U/D14H1E/D14H1A/D14H5U/D14H5E/D14H5A Front Panel
BVM-D14H5U/D14H5E/D14H5A
0 SHIFT button
qa Function buttons
qs OPTION connector
BVM-D14H1U/D14H1E/D14H1A
qs OPTION connector
16
(E)
This manual explains the location and function of parts
and controls of the BVM-D14H5U/D14H5E/D14H5A.
The explanation also applies to the optional BKM-
10R/11R Monitor Control Unit.
1 Tally lamp
With factory settings, the tally lamp lights as follows
1 Tally lamp
when the pins of the PARALLEL REMOTE [1]
connector on the rear panel are shorted:
2 POWER switch
– in red, when pins No.3 and No.9 are shorted.
– in green, when pins No.4 and No.9 are shorted.
3 DEGAUSS button
– in amber, when pins No.3, No.4 and No.9 are
4 Numeric keypad
shorted.
The tally lamp lights as follows when the pins of the
5 MANUAL adjustment
PARALLEL REMOTE [2] connector on the rear panel
buttons and knobs
are shorted:
– in red, when pins No.3 and No.5 are shorted.
6 Menu operation buttons
– in green, when pins No.4 and No.5 are shorted.
7 POWER lamp – in amber, when pins No.3, No.4 and No.5 are
shorted.
8 STANDBY lamp
By changing the setting in the REMOTE menu,
different pins on the remote connector can be used to
9 OVER LOAD lamp
control the tally lamp.
For information about the REMOTE menu, see "[D]
Assigning the Remote Control Functions
— REMOTE Menu" on page 37(E).
2 POWER switch
Press to turn on/off the monitor. By setting with the
1 Tally lamp
ADDRESS menu, it is possible to turn on/off the
power of the specified monitors only, or of all
monitors at the same time.
For information about the ADDRESS menu, see "Selecting
the Monitor to Control — ADDRESS Menu" on page 45(E).
3 DEGAUSS button
Press to degauss the CRT (every time the monitor is
turned on, the CRT is degaussed automatically). To
degauss again, wait for more than five minutes.
4 Numeric keypad
7 POWER lamp
Use to designate the channel number for the input
signal to be monitored, or to enter the setting values
8 STANDBY lamp
with the menus.
9 OVER LOAD lamp
INPUT
Numeric buttons
1 2 3
4 5 6
Ent button: Confirms the
7 8 9
values and characters entered
(ENTER button of the menu
operation buttons 6 has the
Ent
Del 0
same function).
Del button: Deletes the values
and characters entered.
5 MANUAL adjustment buttons and knobs
Each press of one of these buttons turns the button's
green LED on or off. When the corresponding button
is on (lit), it is possible to manually adjust the contrast,
brightness, chroma and phase by turning the
corresponding knobs. The PHASE knob is also used to
enter the setting values with the menus. It is possible to
set the preset value for each adjusting item with the
CONTROL PRESET ADJ menu.
For Information about the CONTROL PRESET ADJ menu,
see " [A] Preset Adjustment of the Picture Level Control
Knobs — CONTROL PRESET ADJ menu" on page 31(E).
CONTRAST button
CONTRAST MANUAL
and knob
BRIGHT
BRIGHT button
and knob
CHROMA
CHROMA button
and knob
PHASE
PHASE button
and knob
Note
The PHASE and CHROMA knobs may not be
adjusted due to the signals. However, these knobs are
used for selecting the items or entering the setting
values with the menus.
(continued)
17
(E)