Sony VPL-PX20 Service Manual page 17

Connecting / Selecting the Menu Language
Right side
DIGITAL
RGB RGB
5BNC
REMOTE CONTROL S VIDEO IN
L R
IN (MONO)
RS-232C S VIDEO VIDEO AUDIO
PLUG IN POWER
OUTPUT INPUT B
MONITOR AUDIO RGB AUDIO MOUSE
INPUT A
DIGITAL
RGB RGB
5BNC
RGB AUDIO MOUSE
USB
DIGITAL RGB R/R-Y/P G/Y B/B-Y/P SYNC/HD VD
R B
BNC Cable Stereo audio
connecting
(not supplied)
cable
(not
supplied)
to RGB/ to
component audio
output output
15k RGB/Component equipment
Notes
• Set the aspect ratio using ASPECT in the INPUT
SETTING menu according to the input signal.
• To connect a 15k RGB/Component equipment,
select the COMPUTER/COMPONENT/DTV
YP P /DTV GBR in the INPUT-A in the SET
B R
SETTING menu according to the input signal.
• Use the composite sync signal when you input the
external sync signal from 15k RGB/component
equipment.
Connecting to a HDTV 1035/60i
Since the screen ratio of a high definition image is
16:9 and 576 lines are displayed in the vertical
direction, the image displayed is not a high-
definition image.
18
(GB)
Selecting the Menu Language
You can select the language for displaying in the
menu and other on screen displays. The factory setting
is ENGLISH.
LAMP/ TEMP/ POWER ON/
COVER FAN SAVING STANDBY
4, 5, 6 3
2
HELP
RESET
1
1
Plug the AC power cord into the wall outlet.
2
Press the I / 1 key to turn on the power.
3
Press the MENU key.
The menu display appears.
4
Select the icon of SET SETTING Menu, the third
one, with the M or m key, then press the , or
ENTER key.
The SET SETTING Menu appears.
INPUT-A
SET SETTING
STATUS: ON
INPUT-A: COMPUTER
AUTO INPUT SEL:OFF
LANGUAGE: ENGLISH
SPEAKER: ON
POWER SAVING: OFF
SIRCS RECEIVER: FRONT&REAR
5
Select LANGUAGE with the M or m key, then
press the , or ENTER key.
6
Select the language desired with the M or m key,
then press the < or ENTER key.
The menu changes into the selected language .
To clear the menu display
Press the MENU key.
The menu display disappears automatically if no key
is pressed for one minute.
Projecting
ON/STANDBY
indicator
LAMP/ TEMP/ POWER ON/
COVER FAN SAVING STANDBY
2
3
HELP
RESET
APS key
4
(Front)
5
Rear
remote
1
control
detector
COMMAND /
2
OFF ON
HELP APA INPUT
3
APA key
MUTING
+
AUDIO PIC
FUNCTION VOLUME
–
1 2
MENU LASER
ENTER R CLICK
RESET D ZOOM
+
–
1
After all equipment is connected completely, plug
the AC power cord into the wall outlet.
The ON/STANDBY indicator lights in red and the
projector goes into the standby mode.
2
Press the I / 1 key.
The ON/STANDBY indicator lights in green.
3
Turn on equipment connected to the projector.
Press the INPUT key to select the input source.
INPUT-A: Selects audio and video signals input
from the INPUT A connector.
Projecting
INPUT-B: Selects audio and video signals input
from the INPUT B connector.
VIDEO: Selects audio and video signals input
from the AUDIO/VIDEO (VIDEO IN)
jacks.
S-VIDEO: Selects audio and video signals input
from the AUDIO/S VIDEO (VIDEO
IN) jacks.
Note
The AUDIO (VIDEO IN) jacks are used as audio
outputs of both VIDEO and S-VIDEO.
4
Turn the zoom ring to adjust the size of the
picture.
5
Turn the focus ring to adjust the focus.
Note
Looking into the lens when projecting may cause
injury to your eyes.
To Press
Adjust the volume the VOL +/– keys on the control panel or
the VOLUME +/– keys on the Remoter
Commander.
Cut off the sound the AUDIO MUTING key on the Remote
Commander. To restore the sound, press
the AUDIO MUTING key again or press
the VOL + key on the control panel or the
VOLUME + key on the Remote
Commander.
Cut off the picture the PIC MUTING key on the Remote
Commander. To restore the picture, press the
PIC MUTING key again.
To get the clearest picture
You can get the suitable picture when a signal from
the computer is input. Press the APA key.
The picture is automatically adjusted to be projected
clearest.
Notes
• Adjust the signal when the still picture is displayed
on the screen.
• Press the APA key when the full image is displayed
on the screen. If there are black edges around the
image, the APA function will not function properly
and the image may extend beyond the screen.
• If you switch the input signal or re-connect a
computer, press the APA key again to get the
suitable picture.
19
(GB)