Simple Start Guide - Sony DVP-NS999ES Service Manual

Simple Start Guide

Quick Overview
A quick overview presented in this guide will
give you enough information to start using the
player for your enjoyment. To use the
surround sound features of this player, refer
to "Hookups" on page 21.
Notes
• You cannot connect this player to a TV that does
not have a video input jack.
• Be sure to disconnect the power cord of each
component before connecting.
Step 1: Unpacking
Check that you have the following items:
• Audio/video cord (pinplug 3 y pinplug
3) (1)
• Power cord (1)
• Remote commander (remote) (1)
• Size AA (R6) batteries (2)
Connecting the power cord
Connect the supplied power cord to the AC
IN terminal of the player.
Step 3: TV Hookups
Connect the supplied audio/video cord and the power cords in the order (1~3) shown below.
Be sure to connect the power cord last.
1
Audio/video
cord (supplied)
to VIDEO to AUDIO OUT
OUT 1 or 2 L/R 1 or 2
AUDIO OUT
1 2
2
L
1
VIDEO
OUT
R
DIGITAL OUT S-LINK AUDIO OUT 5.1CH OUTPUT
1 2 FRONT REAR CENTER
PCM/ DTS/ CONTROL S L
DOLBY DIGITAL IN
L
COAXIAL OPTICAL
COMMAND MODE
1 2 3
R
WOOFER
R
2 2 Y P P
B R SELECTABLE
INTERLACE
PROGRESSIVE
1 1
VIDEO S VIDEO SCAN SELECT
OUT OUT
COMPONENT VIDEO OUT
l : Signal flow
To change the aspect ratio for the
connected TV
Depending on the disc and the TV type
(standard 4:3 screen TV or wide screen TV),
the image may not fit the TV screen.
If this happens, change the aspect ratio
(page 77).
When connecting to a TV that accepts
progressive (480p) format signals
You need to use the COMPONENT VIDEO
OUT jacks to view progressive signals. Hook
up your TV using pattern C on page 21, and
then run Quick Setup on page 31.
Step 2: Preparing the
Remote
You can control the player using the supplied
remote. Insert two Size AA (R6) batteries by
matching the 3 and # ends on the batteries
to the markings inside the compartment.
When using the remote, point it at the remote
sensor on the player.
Notes
• Do not leave the remote in an extremely hot or
humid place.
• Do not drop any foreign object into the remote
casing, particularly when replacing the batteries.
• Do not expose the remote sensor to direct light
from the sun or a lighting apparatus. Doing so
may cause a malfunction.
• If you do not use the remote for an extended
period of time, remove the batteries to avoid
possible damage from battery leakage and
corrosion.
When you have more than one
Sony DVD player
If the supplied remote interferes with your
other Sony DVD player, set the command
mode for this player and the supplied remote
to one that differs from the other Sony DVD
player.
The default command mode setting for this
player and the supplied remote is DVD 1.
COMMAND
MODE switch
,continued 17
TV
to video input
INPUT
(yellow)
VIDEO
(white)
L
AUDIO
(red)
R
to audio input
2
Power source
CD/DVD Player
3
Power source
z Hint
When connecting to a monaural TV, use a stereo-
mono conversion cord (not supplied). Connect the
VIDEO OUT 1/2 jack on the player to the TV's
video input jack, and connect the AUDIO OUT L/R
1/2 jacks to the TV's audio input jack.
19
1
Slide the COMMAND MODE switch on
the remote to select the command
mode (DVD 1, DVD 2, or DVD 3) so that
the setting for the remote differs from
the other DVD players.
For example, if other DVD players
respond to the default command mode
setting for the supplied remote (DVD 1),
set the remote to DVD 2 or DVD 3.
2
Slide the COMMAND MODE switch on
the rear of the player so it matches
that of the supplied remote.
18
Step 4: Playing a Disc
With the playback side facing down
A Turn on the TV.
B Press [/1 on the player.
C Switch the input selector on your
TV so that the signal from the
player appears on the TV screen.
D Press A on the player to open the
disc tray.
E Place the disc on the tray with the
playback side facing down.
F Press H.
The disc tray closes and the player begins
playing the disc.
20
1-4
After step 6
Depending on the disc, a menu may be
displayed on the TV screen. If so, select the
item you want from the menu and play the
DVD VIDEO (page 39) or VIDEO CD
(page 42).
To stop playing
Press x.
To remove the disc
Press A.
To turn off the player
Press [/1. The player enters standby mode
and the power indicator lights up in red.