Advertisement
Available languages
Available languages
ATS-162R
Order No. 25.4580
16-Channel Audio Receiver
GB
Please read these operating instructions care-
fully prior to operation and keep them for later
reference.
1 Applications
In combination with the transmitter ATS-162T,
the receiver ATS-162R provides a mobile wire-
less system for audio transmission, suitable e. g.
for guided tours, lectures in different languages,
wireless command transmission or wireless
transmissions of audio signals with line level.
For transmission, 16 channels are available in
the frequency range 863 – 865 MHz, up to 8 chan-
nels may be used at the same time without
mutual interference. The transmission range de-
pends on local conditions and may reach 50 m
as a maximum.
The receiver may also be combined with the
units TXA-800ST, TXA-802CD and TXA-1002CD
as these units transmit on the same frequencies.
2 Important Notes
The unit corresponds to all relevant directives of
the EU and is therefore marked with
G
The unit is suitable for indoor use only. Protect
it against dripping water and splash water,
high air humidity and heat (admissible ambi-
ent temperature: 0 – 40 °C).
G
For cleaning only use a dry, soft cloth; never
use water or chemicals.
G
No guarantee claims for the unit and no liabil-
ity for any resulting personal damage or mate-
rial damage will be accepted if the unit is used
for other purposes than originally intended, if it
is not correctly connected or operated, or if it is
not repaired in an expert way.
If the unit is to be put out of operation
definitively, take it to a local recycling
plant for a disposal which is not harm-
ful to the environment.
1
2
3
4
5
ON
ATS-162R
SET
3 Setting into Operation
3.1 Recharging the battery
For mobile operation the ATS-162R is equipped
with a rechargeable lithium polymer battery.
To recharge it, use the charger ATS-162C* or
the charger ATS-162PS*. With a battery fully
charged, the receiver can be operated for ap-
prox. 20 hours.
* The charger ATS-162C allows to recharge the batter-
ies of up to 30 units at the same time, the charger
ATS-162PS allows to recharge the batteries of 2 units.
Hints for a long battery life:
– Prior to the first setting into operation fully
charge the battery.
– If the battery is discharged (the battery sym-
bol on the left of the display flashes), fully
recharge it as soon as possible.
– Recharge the battery frequently.
3.2 Operation with a 5 V power supply unit
The receiver can also be operated with a 5 V
power supply unit* when a mains socket is avail-
able at the place of application. Thus, a longer
operation is possible than it is provided with a
.
battery fully recharged; at the same time the bat-
tery is recharged. For connection, a low voltage
plug of the dimensions 3.5 / 1.35 mm (outside / in-
side diameter) is required. The positive pole
must be at the inner contact. Connect the power
supply unit to the lateral jack (8).
* e. g. the model PSS-600E from MONACOR or the power
supply unit provided with the charger ATS-162PS.
3.3 Connecting the earphone or
using the audio output
The signal received can be monitored via the in-
tegrated speaker (4). As an alternative, the sup-
plied earphone can be used. Connect the ear-
phone to the jack
switched off] and attach it to your ear.
The audio signal can also be fed from the
3.5 mm jack
(5) to a line input of an audio unit
(amplifier, mixer, recorder etc.). When connect-
ing the jack
, the speaker and an earphone
connected are switched off.
4 Operation
1) First switch on the receiver only: Turn the on /
off switch and volume control
so that the display (6) shortly shows "On".
2) Set a free transmission channel with the but-
ton + or - (7). To indicate the corresponding
frequency, press the button SET.
The button
shows blue, interference or signals from other
transmitters are received. In this case use a
1 Jack
for the supplied earphone
When connecting the earphone, the speaker
(4) is switched off.
2 Charge LED for the internal battery
3 On / off switch and volume control
6
4 Speaker
5 Output jack
7
audio signal (line level)
When connecting the jack, the speaker and
an earphone connected are switched off.
8
6 Display to indicate the transmission channel
9
(01 – 16) and the battery status
®
MONACOR INTERNATIONAL GmbH & Co. KG • Zum Falsch 36 • 28307 Bremen • Germany
©
Copyright
by MONACOR INTERNATIONAL. All rights reserved.
(1) [the speaker is thus
(3) clockwise
(9) must not show blue. If it
(3.5 mm jack) for the received
different channel. If it shows or flashes red,
the button has been pressed and a signal
which may possibly be received is muted.
Then press the button again.
3) Switch on the corresponding transmitter and
set it to the transmission channel of the re-
ceiver (
manual of the transmitter). On the
receiver, the button
shows blue as soon as
a signal is received.
4) Adjust the desired volume for the speaker (4),
the earphone or the output signal of the
jack
(5) with the control
Caution! Never adjust a very high volume.
Permanent high volumes may damage your
hearing!
5) To mute the received audio signal, use the
button
. Then the button flashes red. To
switch on again, press the button once more.
6) If several ATS-162 systems are used at the
same time for transmitting different signals,
set a different channel for each separate sys-
tem. Up to eight audio signals can be trans-
mitted at the same time if channels 1 to 8 are
used for this purpose.
7) To switch off the receiver, turn the control
counter-clockwise until the display shortly
shows "OFF".
5 Specifications
Receiving frequency: . . 863 – 865 MHz
Range: . . . . . . . . . . . . . approx. 50 m
Audio output: . . . . . . . . . line level,
3.5 mm jack
Power supply: . . . . . . . . rechargeable lithium
polymer battery
1200 mAh or
5 V / 65 mA
Ambient temperature: . . 0 – 40 °C
Dimensions: . . . . . . . . . 52 × 100 × 38 mm
Weight: . . . . . . . . . . . . . 90 g
Channel assignment
Channel
MHz
Channel
01
863.1
09
02
864.1
10
03
863.6
11
04
864.6
12
05
863.3
13
06
864.3
14
07
863.8
15
08
864.8
16
Subject to technical modification.
7 Buttons + and - for setting the receiving chan-
nel and
button SET for short indication of the receiving
frequency
8 Jack to connect a 5 V PSU
9 Button
for muting
does not light up = no signal is received
shows blue =
a signal is received
flashes red =
the audio signal received is
muted.
shows red =
no signal is received and
muting On
A-1363.99.01.09.2012
(3).
MHz
863.2
864.2
863.7
864.7
863.4
864.4
863.9
864.9
Advertisement
