Table of Contents
Advertisement
更多难得资料请到江南家电维修论坛免费下载！
http://bbs.520101.com
19" LCD Color Monitor
Service
Service
Service
Description
Table of Contents.....................................................1
Revision List................................................................2
Important Safety Notice.............................................3
1. Monitor Specifications................................................4
2. LCD Monitor Description............................................5
3.1General Instructions...........................................6
3.2 Control buttons................................................6
3.3 OSD Menu.........................................................8
4. Input/Output Specification......................................10
4.1 Input Signal Connector.........................................10
4.2 Factory Preset Display Modes................................10
4.3 Pixel Defect Policy..........................................11
4.4 Failure Mode of Panel .....................................14
5. Block Diagram.................................................15
5.1 Software Flow Chart.............................................15
5.2 Electrical Block Diagram.......................................17
6. Schematic Diagram................................................. 19
ANY PERSON ATTEMPTING TO SERVICE THIS CHASSIS MUST FAMILIARIZE HIMSELF WITH THE
CHASSIS AND BE AWARE OF THE NECESSARY SAFETY PRECAUTIONS TO BE USED WHEN
SERVICING ELECTRONIC EQUIPMENT CONTAINING HIGH VOLTAGES.
CAUTION: USE A SEPARATE ISOLATION TRANSFOMER FOR THIS UNIT WHEN SERVICING
REFER TO BACK COVER FOR IMPORTANT SAFETY GUIDELINES
Copyright 2008 Philips Consumer Lifestyle
Page
Page
SAFETY NOTICE
Subject to modification ○
190V1SB/93
190V1SB/00
190V1SB/62
190V1SB/27
Description
6.1 Main Board......................................................19
6.2 Power Board...............................................23
6.3 Key Board.........................................................25
7. PCB Layout.........................................................26
7.1 Main Board........................................................26
7.2 Power Board...................................................28
7.3 Key Board.........................................................30
8. Wiring Diagram...................................................31
9. Scalar Board Overview........................................32
10. Mechanical Instructions........................................33
11. Repair Flow Chart...............................................37
12. ISP Instructions...........................................................43
13. DDC Instructions.........................................................46
14. White Balance, Luminance Adjustment..................56
15. Monitor Exploded View................................................58
16. Recommended & Spare Parts List............................59
17. Different Parts List.............................................61
18. General Product Specification................................63
Apr, 01, 2009
K
Chassis: Meridian 1
Page
GB
312278518560
Advertisement
Chapters
Table of Contents
Related Manuals for Philips 190V1SB/93
Summary of Contents for Philips 190V1SB/93
-
Page 1: Table Of Contents
CHASSIS AND BE AWARE OF THE NECESSARY SAFETY PRECAUTIONS TO BE USED WHEN SERVICING ELECTRONIC EQUIPMENT CONTAINING HIGH VOLTAGES. CAUTION: USE A SEPARATE ISOLATION TRANSFOMER FOR THIS UNIT WHEN SERVICING REFER TO BACK COVER FOR IMPORTANT SAFETY GUIDELINES Copyright 2008 Philips Consumer Lifestyle Subject to modification ○ Apr, 01, 2009 312278518560... -
Page 2: Revision List
更多难得资料请到江南家电维修论坛免费下载！ http://bbs.520101.com Meridian 1 Revision List Version Release Date Revision History Apr, 01,2009 Initial release, Draft Version Apr ,13 ,2009 Add CTV Model 190V1SB/62 Apr, 16 ,2009 Add CTV Model 190V1SB/27... -
Page 3: Important Safety Notice
Meridian 1 Important Safety Notice Proper service and repair is important to the safe, reliable operation of all Philips Company Equipment. The service procedures recommended by Philips and described in this service manual are effective methods of performing service operations. Some of these service operations require the use of tools specially designed for the purpose. -
Page 4: Monitor Specifications
更多难得资料请到江南家电维修论坛免费下载！ http://bbs.520101.com Meridian 1 1. Monitor Specifications 1.1 Technical specifications LCD PANEL TFT LCD • Type • Screen size 19” Visual • Pixel pitch 0.285mm x 0.285mm • LCD Panel type 1440*900 pixels R.G.B vertical stripe Anti-glare polarizer, hard coated •... -
Page 5: Lcd Monitor Description
更多难得资料请到江南家电维修论坛免费下载！ http://bbs.520101.com Meridian 1 1.2 Physical specifications • Tilt - 5°~ 20° • Power Supply 100~240 V AC, 50/60Hz • Power Consumption <35W (Typ.) to 40 (operating) ℃ ℃ • Temperature to 60 (storage) ℃ ℃ • Relative Humidity 20~80% •... -
Page 6: Operating Instructions
更多难得资料请到江南家电维修论坛免费下载！ http://bbs.520101.com Meridian 1 3. Operating Instructions 3.1 General Instructions Press the power button to turn the monitor on or off. The other control knobs are located at front panel of the monitor (see figure). By changing these setting, the picture can be adjusted to your personal preference. ﹡... - Page 7 更多难得资料请到江南家电维修论坛免费下载！ http://bbs.520101.com Meridian 1 Rear View Kensington anti-thief lock AC power input DVI-D(available for selective models） VGA input...
-
Page 8: Osd Menu
Meridian 1 3.3 OSD Menu This is a feature in all Philips LCD monitors. It allows an end user to adjust screen performance of the monitors directly through an on-screen instruction window. The user interface provides user-friendliness and ease-of-use when operating the monitor. - Page 9 更多难得资料请到江南家电维修论坛免费下载！ http://bbs.520101.com Meridian 1 The OSD tree Below is an overall view of the structure of the On-Screen Display. You can use this as a reference when you want to work your way around the different adjustments later on.
-
Page 10: Input/Output Specification
更多难得资料请到江南家电维修论坛免费下载！ http://bbs.520101.com Meridian 1 4. Input/ Output Specification 4.1 Input Signal Connector Analog connectors Pin No. Signal Name Pin No. Signal Name Red video input DDC +5V Green video input/ SOG Logic ground Blue video input Ground Sense (GND) Serial data line (SDA) Cable Detect (GND) H. -
Page 11: Pixel Defect Policy
4.3 Pixel Defect Policy Philips strives to deliver the highest quality products. We use some of the industry’s most advanced manufacturing process and practice stringent quality control. However, pixel or sub pixel defects on the TFT LCD panels used in flat panel monitors are sometimes unavoidable. - Page 12 In order to qualify for repair or replacement due to pixel defects during the warranty period, a TFT LCD panel in a Philips flat panel monitor must have pixel or sub pixel defects exceeding the tolerances listed in the following tables.
- Page 13 更多难得资料请到江南家电维修论坛免费下载！ http://bbs.520101.com Meridian 1 BLACK DOT DEFECTS ACCEPTABLE LEVEL MODEL 190V1 1 dark subpixel 2 adjacent dark subpixels 3 adjacent dark subpixels Distance between two black dot defects * >15mm Total black dot defects of all types TOTAL DOT DEFECTS ACCEPTABLE LEVEL MODEL 220E1...
-
Page 14: Failure Mode Of Panel
更多难得资料请到江南家电维修论坛免费下载！ http://bbs.520101.com Meridian 1 4.4 Failure Mode Of Panel Quick reference for failure mode of LCD panel this page presents problems that could be made by LCD panel. It is not necessary to repair circuit board. Simply follow the mechanical Polarizer has bubbles instruction on this manual to eliminate failure by replace LCD panel. -
Page 15: Block Diagram
更多难得资料请到江南家电维修论坛免费下载！ http://bbs.520101.com Meridian 1 5. Block Diagram 5.1 Software Flow Chat... - Page 16 更多难得资料请到江南家电维修论坛免费下载！ http://bbs.520101.com Meridian 1 1) MCU initializes. 2) Is the EPROM blank? 3) Program the EPROM by default values. 4) Get the PWM value of brightness from EPROM. 5) Is the power key pressed? 6) Clear all global flags. 7) Are the AUTO and SELECT keys pressed? 8) Enter factory mode.
-
Page 17: Electrical Block Diagram
更多难得资料请到江南家电维修论坛免费下载！ http://bbs.520101.com Meridian 1 5.2 Electrical Block Diagram 5.2.1 Main Board Flash Memory Panel Interface PM25LV010A (CN301) (U402) Crystal 12MHz (X401) Scalar IC NT68667FG/C EEPROM M24C16 (Include MCU, ADC, OSD) Keypad Interface (U403) (U401) (CN402) EEPROM M24C02 EEPROM M24C02 (U102) (U108) RXN/P H/V sync... - Page 18 更多难得资料请到江南家电维修论坛免费下载！ http://bbs.520101.com Meridian 1 5.2.2 Power/Inverter Board AC input Bridge Rectifier Transformer EMI filter Rectifier diodes and Filter Start Resistor R904, R905 Feedback PWM Control Circuit Power Switch (IC901) （Q901） Photocoupler (IC903) Output Transformer MOSFET (PT801) Circuit Q805, Q806 Lamp ON/OFF PWM Control Feedback...
-
Page 19: Schematic Diagram
更多难得资料请到江南家电维修论坛免费下载！ Meridian 1 http://bbs.520101.com 6. Schematic 6.1 Main Board 715G3226-1 CN101 A1 CN102 B1 INPUT C101 B3 C102 A4 C103 A2 C104 A2 C105 A4 C106 A4 C107 A4 C108 A4 C109 A4 C110 A4 C111 B4 C112 A3 C113 B4 C114 B4 C115 C2 C117 D4... - Page 20 更多难得资料请到江南家电维修论坛免费下载！ http://bbs.520101.com Meridian 1 OUTPUT CN301 A5 CN302 CN401 C1 CN402 D1 CN403 B2 CN404 C2 CN405 D2 C301 C302 C303 C304 C305 C431 C432 C433 C434 C435 C436 FB301 A3 FB402 Q301 Q302 R301 R302 R303 R304 R305 R306 R307 R308 R436...
- Page 21 更多难得资料请到江南家电维修论坛免费下载！ Meridian 1 http://bbs.520101.com POWER use Pin 123 control BL-ON [on_BACKLIGHT_1]; CN701 A1 C701 B2 C702 C1 C703 A2 C704 B5 C705 B5 C706 C4 C707 C5 R446: 0 Ohm; R708: 10K; R704: 22K; R702: 1K; Q701: 2N3904; C702: 0.1uF C708 C709 C4 C710 A2...
- Page 22 更多难得资料请到江南家电维修论坛免费下载！ http://bbs.520101.com Meridian 1 SCALER CN406 A4 C401 C403 A1 C404 C406 A2 C407 C410 C411 C412 C413 A2 C420 D2 C421 D2 C422 D1 C423 A1 C430 A1 C438 C439 B1 C440 A1 C442 C446 C447 B1 C448 FB401 A1 FB403 A2 FB404 A1 FB406 A1...
-
Page 23: Power Board
更多难得资料请到江南家电维修论坛免费下载！ Meridian 1 http://bbs.520101.com 6.2 Power Board 715G2824-3-5 Adapter BD901A A1 BD901 A1 CN901 D1 CN902 C3 CN903 C2 C900 C901 C902 C903 C904 C905A B1 C906 C907 C908 C909 C912 C915 C917 C918 C921 C924 C928 C929 C931 C932 C937 C938 C939... - Page 24 更多难得资料请到江南家电维修论坛免费下载！ http://bbs.520101.com Meridian 1 Inverter CN802 A5 CN804 B5 C801 B1 C802 A2 C804 B3 C805 B2 C806 B1 C808 B3 C809 B3 C810 B2 C811 B3 C812 B1 C813 B4 C814 B4 C815 A3 C817 B4 C818 B1 D801 B3 D803 C5 D806 B3 IC801 B2...
-
Page 25: Key Board
更多难得资料请到江南家电维修论坛免费下载！ Meridian 1 http://bbs.520101.com 6.3 Key Board 715G3016-1A KEY-PAD-SWITCH CN001 B1 C001 C002 C003 C004 C005 C006 C007 C008 C009 C010 JR001 LED001 A2 R001 R002 R004 R005 SW001 C5 SW002 C4 SW003 C5 SW004 C4 SW005 C3 ZD001 C4 ZD002... -
Page 26: Pcb Layout
更多难得资料请到江南家电维修论坛免费下载！ http://bbs.520101.com Meridian 1 7. PCB Layout 7.1 Main Board 715G3226-1... - Page 27 更多难得资料请到江南家电维修论坛免费下载！ Meridian 1 http://bbs.520101.com...
-
Page 28: Power Board
更多难得资料请到江南家电维修论坛免费下载！ http://bbs.520101.com Meridian 1 7.2 Power Board 715G2824-3-5... - Page 29 更多难得资料请到江南家电维修论坛免费下载！ Meridian 1 http://bbs.520101.com...
-
Page 30: Key Board
更多难得资料请到江南家电维修论坛免费下载！ http://bbs.520101.com Meridian 1 7.3 Key Board 715G3016-1A... -
Page 31: Wiring Diagram
更多难得资料请到江南家电维修论坛免费下载！ Meridian 1 http://bbs.520101.com 8. Wiring Diagram Panel CN802 CN902 30 Pin CN301 Power Board CN701 Main Board CN804 NT68667FG/C (U401) CN901 CN402 CN102 AC IN 6 Pin Key Board CN001... -
Page 32: Scalar Board Overview
更多难得资料请到江南家电维修论坛免费下载！ http://bbs.520101.com 32 32 Meridian 1 9. Scalar Board Overview DC-DC EEPROM NT68667FG/C Flash ROM D-SUB EEPROM DVI EEPROM... -
Page 33: Mechanical Instructions
更多难得资料请到江南家电维修论坛免费下载！ http://bbs.520101.com Meridian 1 10. Mechanical Instructions 1. Place the monitor face down on a smooth surface, and release three screws to remove the stand-base ass’y. Note: Be careful to avoid scratch and injury during the process of uninstall. 2. Use disassembly tool to open 6 latches at top of bezel as follow: 3. - Page 34 更多难得资料请到江南家电维修论坛免费下载！ http://bbs.520101.com 34 34 Meridian 1 4. Remove the key board from the bezel and remove the bezel. 5. Remove main frame. A. Disconnect two connectors and four screws.
- Page 35 更多难得资料请到江南家电维修论坛免费下载！ http://bbs.520101.com Meridian 1 B. Press to release left and right latches of LVDS cable, and then disconnect it. 6. Remove Power Board and Main Board. A. Remove four screws and mainframe.
- Page 36 更多难得资料请到江南家电维修论坛免费下载！ http://bbs.520101.com 36 36 Meridian 1 B. Remove three screws to remove the Power Board and Main Board from mainframe. C. Disconnect three connectors from Main Board.
-
Page 37: Repair Flow Chart
更多难得资料请到江南家电维修论坛免费下载！ http://bbs.520101.com Meridian 1 11. Repair Flow Chart 11.1 Main Board (1). No Power No power Press power key and look if the picture is normal Please reinsert and make sure the AC of 90-264V is normal Reinsert or check the Adapter/Inverter section Measure U703 PIN2=3.3V Check C706, C707 and U703... - Page 38 更多难得资料请到江南家电维修论坛免费下载！ http://bbs.520101.com 38 38 Meridian 1 (2). No Picture No picture X401 oscillate Replace X401 The button is under control waveform is normal Check Correspondent Check reset circuit of component U401 is normal Measure U703 PIN2=3.3V Replace U401 Check C706, C707 and U703 X401 oscillate waveform is normal Replace X401 Check HS VS from CN101 is normal...
- Page 39 更多难得资料请到江南家电维修论坛免费下载！ http://bbs.520101.com Meridian 1 (3). White screen White screen Measure Q302 base is low level? X401 oscillate waveform is normal Replace X401 Check Q301, Q302 is broken or CN301 solder? Check reset circuit of U401 is normal Check Correspondent Check Correspondent component.
- Page 40 更多难得资料请到江南家电维修论坛免费下载！ http://bbs.520101.com 40 40 Meridian 1 11.2. Power/Inverter Board (1) No power Check ZD902 ＝16V Check AC line volt is 90V or 264V Check AC input Check the voltage of C905A (+) Check bridge rectified circuit and F901 circuit Check start voltage for the pin8 of IC901 Check R904, R905 and Change IC901 Check the auxiliary voltage is bigger than 16V and smaller than 32V...
- Page 41 更多难得资料请到江南家电维修论坛免费下载！ http://bbs.520101.com Meridian 1 (2) W / LED, No Backlight Check ZD902 ＝16V Check adapter or MB Check ON/OFF signal Check Main Board Check IC801 PIN6, PIN10=16V Check ZD802, ZD803 Check IC801 PIN8, 9 have the output of square wave at short time Change IC801 Check Q805 and Q806 have the output of square wave at short time.
- Page 42 更多难得资料请到江南家电维修论坛免费下载！ http://bbs.520101.com 42 42 Meridian 1 11.3 Key Board OSD is unstable or not working Is Key Pad Board connecting normally? Connect Key Pad Board Replace Button Switch Is Button Switch normally? Replace Key Pad Board Is Key Pad Board normally? Check Main Board...
-
Page 43: Isp Instructions
ISP BOARD x1 b. Printer cablex1 c. VGA cable x1 12.1 Install the “EasyUSB WriterV4.1” 12.2 Connect the ISP board as follow: Connect to Connect to the the PC LPT Philips 190V1 12.3 The process of ISP write is as follow:... - Page 44 更多难得资料请到江南家电维修论坛免费下载！ http://bbs.520101.com 44 44 Meridian 1 a) Double-click ，running the program as follows: Click icon and the program runs as follows:...
- Page 45 更多难得资料请到江南家电维修论坛免费下载！ http://bbs.520101.com Meridian 1 Click icon, search the correct program and click open: Click icon. If it burns successfully, it will show as the follow picture:...
-
Page 46: Ddc Instruction
The process of installing “PORT95NT” has been specified in, so it will not be specified again. If you have any problem, please read it. 13.2 Connect the DDC Board as follow: Connect to the When you write analog PC LPT EDID, Connect this port to the Philips 190V1’s VGA port 12V Input... - Page 47 更多难得资料请到江南家电维修论坛免费下载！ http://bbs.520101.com Meridian 1 13.3 The process of ISP write is as follow: a. Double-click ，appear as follow: b. Choose “Analog ” and then click “Loadfile”, it will show the picture as follow:...
- Page 48 更多难得资料请到江南家电维修论坛免费下载！ http://bbs.520101.com 48 48 Meridian 1 c. Input the information of the analog, it will show the picture as follow: d. Click “OK”, and choose the correct file.
- Page 49 更多难得资料请到江南家电维修论坛免费下载！ http://bbs.520101.com Meridian 1 e. Click “OK”, and then click “Read A”, it will show the picture as follow: Key in the same 14 numbers in the Input SN and Verify SN, then click “Program”, when the analog DDC Write complete, it will show the picture as follow: Note: The way of digital DDC Write is the same as analog.
- Page 50 更多难得资料请到江南家电维修论坛免费下载！ http://bbs.520101.com 50 50 Meridian 1 190V1 EDID Analog 1128 bytes EDID Data (Hex): 00 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 00 FF FF FF FF FF FF 00 41 0C 81 00 E9 D9 01 00 16: 20 0B 01 03 0E 28 19 78 2A A1 50 A3 57 4C 9D 25 32: 11 50 54 BF EF 80 71 4F 81 80 95 00 95 0F 01 01 48: 01 01 01 01 01 01 9A 29 A0 D0 51 84 22 30 50 98...
- Page 51 更多难得资料请到江南家电维修论坛免费下载！ http://bbs.520101.com Meridian 1 Separate Sync Support: Composite Sync Support: Yes Sync. on green video supported:Yes Serration of the Vsync.Pulse is not required. Max. H. Image Size : 40cm. Max. V. Image Size : 25cm. Display Gamma: DPMS Features, Active off: Yes.
- Page 52 Detailed Timing: 1440x900 @ 60Hz. <-x-Detailed Timing Descriptions-x-> <---Detailed Timing Descriptions---> Detailed Timing: FF (Monitor SN) '231313212132' Detailed Timing: FC (Monitor Name) 'Philips 190V' Detailed Timing: FD (Monitor limits) Min. V. rate: 56Hz Max. V. rate: 76Hz Min. H. rate: 30KHz Max.
- Page 53 更多难得资料请到江南家电维修论坛免费下载！ http://bbs.520101.com Meridian 1 Digital (only for 220E1SB/69) 128 bytes EDID Data (Hex): 00 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 00 FF FF FF FF FF FF 00 41 0C 81 00 29 E7 04 00 16: 15 0D 01 03 80 28 19 78 2A A1 50 A3 57 4C 9D 25 32: 11 50 54 BF EF 80 71 4F 81 80 95 00 95 0F 01 01 48: 01 01 01 01 01 01 9A 29 A0 D0 51 84 22 30 50 98...
- Page 54 更多难得资料请到江南家电维修论坛免费下载！ http://bbs.520101.com 54 54 Meridian 1 Display Gamma: DPMS Features, Active off: Yes. Display Type: R/G/B color display. Preferred Timing Mode: Yes. <---Basic Display Parameters/Features---> <---Color Characteristics---> Red x: 0.6386718750 Red y: 0.3417968750 Green x: 0.2968750000 Green y: 0.6142578125 Blue x: 0.1455078125 Blue y: 0.0673828125...
- Page 55 Detailed Timing: 1440x900 @ 60Hz. <-x-Detailed Timing Descriptions-x-> <---Detailed Timing Descriptions---> Detailed Timing: FF (Monitor SN) '123232132132' Detailed Timing: FC (Monitor Name) 'Philips 190V' Detailed Timing: FD (Monitor limits) Min. V. rate: 56Hz Max. V. rate: 76Hz Min. H. rate: 30KHz Max.
-
Page 56: White Balance, Luminance Adjustment
56 56 Meridian 1 14. White Balance, Luminance Adjustment 1. Apparatuses and program: analyzer CA-210, PC, tool, FGA adjustment program (PHILIPS 190V1.DDCI), Pattern generator. 2. Equipment installation: a. Connect analyzer CA-210 to PC by USB connector, install drive program CA-SDK Ver4.00 for CA-210 and restart PC after finish installing b. - Page 57 更多难得资料请到江南家电维修论坛免费下载！ http://bbs.520101.com Meridian 1 4. Color Temp confirmation Connect the signal to the monitor, the monitor displays white-picture, use CA-210 to measure the Color Temp of the screen center and select the OSD to make sure whether the Color Temps accord with the SPEC.
-
Page 58: Monitor Exploded View
更多难得资料请到江南家电维修论坛免费下载！ http://bbs.520101.com 58 58 Meridian 1 15. Monitor Exploded View... -
Page 59: Recommended & Spare Parts List
FQ301 089G414A15N IS POWER CORD FQ204 Q70G900281310A 190V1 CD MANUAL FQ205 705GQ8CS002 CUSHION ASSY FQ202 Q44G9115813 6A 19W LCD PHILIPS CARTON FQ206 Q41G780A81325A 190V1 QSG IC903 056G 139 3A IC PC123Y22FZ0F T901 080GL22T 3 S1 X'FMR 490uH PT801 080GL24T 23 H INVERTER X'FMR 68.5uH... - Page 60 Meridian 1 U105 056G 662502 IC ESD AZC199-04S SOT23-6L U106 056G 662502 IC ESD AZC199-04S SOT23-6L U107 056G 662502 IC ESD AZC199-04S SOT23-6L Service Kit Description Part No. Philips 12NC Picture DDC KIT 715G2005C2 996500043197 NOVATEK ISP KIT 715LT035A 996500043198...
-
Page 61: Different Parts List
更多难得资料请到江南家电维修论坛免费下载！ http://bbs.520101.com Meridian 1 17. Different Parts List Diversity of 190V1SB /00 compared with 190V1SB/93 190V1SB /00 190V1SB /93 Location PCM Codes Description PCM Codes Description FQ301 089G404A15N IS POWER CORD 089G414A15N IS POWER CORD FQ202 Q44G9115813 4A 19W LCD PHILIPS CARTON... - Page 62 更多难得资料请到江南家电维修论坛免费下载！ http://bbs.520101.com 62 62 Meridian 1 Diversity of 190V1SB/27 compared with 190V1SB/93 190V1SB/27 190V1SB/93 Location PCM Codes Description PCM Codes Description FQ301 089G402A15N IS POWER CORD 089G414A15N IS POWER CORD...
-
Page 63: General Product Specification
5.2 MECHANICAL DATA FILES ------ PROE FILES REQUIRED 5.3 LOCATION OF PHILIPS LOGO ------- PER PHILIPS MAKE-UP SHEET 5.4 GAP BETWEEN PANEL AND FRONT BEZEL ------- <1.4mm (type), AGREED BY PHILIPS. 5.5 LOCATION OF CONTROL ICONS ------- PER PHILIPS GRAPHIC SHEET 5.6 COLOR FOR RESIN/PAINT ------- PER PHILIPS MAKE-UP SHEET... - Page 64 6.3 DISPLAY DISTURBANCES FROM EXTERNAL ENVIRONMENT 6.4 DISPLAY DISTURBANCES TO EXTERNAL ENVIRONMENT RELIABILITY 7.1 MEAN TIME BETWEEN FAILURES QUALITY ASSURANCE REQUIREMENTS 8.1 ACCEPTANCE TEST PHILIPS’ FLAT PANEL MONITORS PIXEL DEFECT POLITY 10. REGULATORY COMPLIANCE 10.1 WORLDWIDE REGULATORY 10.2 EMC REQUIREMENTS 10.3 ROHS 10.4 WEEE...
-
Page 65: Foreword
30 minutes that brightness stability is optimal, and follow strictly after panel specification. 2. PRODUCT PROFILE This display monitor unit is a color display monitor enclosed in Philips styling cabinet which has an integrated tilt base. Tier1: 1. LGD 19”, CMO 19”... -
Page 66: Scanning Frequencies
3.2 Interface 3.2.1 D-SUB Cable Length 1.5m +/- 50mm Not fix with monitor when packing (agreed by Philips), with transplant pin protective cover. Connector type D-sub male with DDC2B pin assignments Blue connector thumb-operated jack screws Pin assignments PIN No. - Page 67 更多难得资料请到江南家电维修论坛免费下载！ http://bbs.520101.com Meridian 1 3.2.2 Software control functions via OSD/Control adjustment functions Please refer to following Hudson 8 OSD definitions Auto\Back Input\ ▼ Brightness\ ▲ Menu\Enter Power Reset - No: Exit Yes: Auto adjustment for displaying timing mode and recall factory preset OSD Languages English Spanish...
-
Page 68: Timing Requirement
Power on Show PHILIPS logo 3 sec. --> change to input signal Any deviation between document and sample, than refer to approved sample by Philips. 3.3 Timing requirement Factory Preset mode definition: 1. Perfect FOS while presenting all required timings 2. -
Page 69: Horizontal Scanning
更多难得资料请到江南家电维修论坛免费下载！ http://bbs.520101.com Meridian 1 800x600/60 40.00 37.88 60.32 p / p 800x600/72 50.00 48.08 72.19 p / p 800x600/75 49.50 46.88 75.00 p / p 832x624/75 57.28 47.73 74.55 n / n 1024x768/60 65.00 48.36 60.00 n / n 1024x768/70 75.00 56.48 70.07... -
Page 70: Power Management (Support To Input)
6 sec 5 sec MONITOR CONTROLS Lock LOCKED MONITOR CONTROLS UNLOCKED (default) Factory Mode [AUTO]+[Menu]+[Power] DDC/CI On/OFF [MENU]+[DOWN] 5 sec 5 sec DDC/CI ON (default) for VISTA DDC/CI OFF Any deviation between document and sample, please refer to Philips approved sample. -
Page 71: Visual Characteristics
更多难得资料请到江南家电维修论坛免费下载！ http://bbs.520101.com Meridian 1 Visual characteristics 4.1 Test conditions Unless otherwise specified, this specification is defined under the following conditions. (1) Input signal: As defined in 3.3, 1440*900 non-interlaced mode (1440*900@60Hz 140MHz), signal sources must have 75 ohm output impedance (2) Luminance setting: controls to be set to 300 nits with full screen 100 % duty cycle white signal (3) Warm up:... -
Page 72: Mechanical Characteristics
All major plastic parts (bezel, back cover) need to be molded from same resin. Plastic resin type selection should be referred to “TY R83-2-9002-1”. 5.11 Texture/Glossing of housing • The texture area and texture no should follow Philips make-up sheet. • The exterior surfaces shall have a uniform texture. •... -
Page 73: Tilt And Swivel Base
• Regulatory label follow Philips requirement • China RoHS label • Detail document refer to Philips Engineering Reference Book 5.15 Product dimension / Weight (Refer to Philips approved SHT 191/SHT560) • Unit dimension : 439(w)*363(H)*191(D) • Packed unit dimension: : 490(w)*375(D)*145(H) •... -
Page 74: Pallet/Container Loading
更多难得资料请到江南家电维修论坛免费下载！ http://bbs.520101.com 74 74 Meridian 1 5.16.2 Transportation Test Follow TPV standard Transportation test specification for all regions • Random Vibration test • Drop test 5.17 Pallet / Container loading Transportation standards refer to TPV standard. • Air shipment. • Sea container 20'(pallet/slip sheet) •... -
Page 75: Reliability
According to MIL-STD-105D Control II level AQL: 0.4 (major) 1.5 (minor) (Please also refer to annual quality agreement) Customer acceptance criteria: UAW0377/00 Philips’ Flat Panel Monitors Pixel Defect Policy Philips’ Flat Panel Monitors Pixel Defect Policy BRIGHT DOT DEFECTS ACCEPTABLE LEVEL MODEL... - Page 76 更多难得资料请到江南家电维修论坛免费下载！ http://bbs.520101.com 76 76 Meridian 1 Fig 1: Measurement locations of Brightness Uniformity Fig 2: Cross talk pattern Gray level 46 (64 Gray level) Fig 3: Cross talk Pattern Center at Gray level 0 (Black)
-
Page 77: Regulatory Compliance
EUROPE EN55022:2006, HDMI have to test PC EN55024:1998+A1:2001+ EMC/CE test report mode and DVD mode A2:2003, EN61000-3-2:2006, EN61000-3-3:1995+A1:20 01+A2:2005 Philips is OEM licence EN60950-1:2001 TUV certificate Optional holder TUV-ERG certificate LCD: ISO13406-2, prEN Philips is OEM licence Optional 50279:1998 TUV ISO13406-2... - Page 78 To add all sales name TCO'06 Optional certificate into certificate Supplier to contact EN60950-1:2001 S+ PZ1 certificate Philips NSO Heidi and apply for Switzerland certification. Supplier to pay approbation cost 2450 CHF each model and each extend model 300 CHF. To provide CB,...
- Page 79 更多难得资料请到江南家电维修论坛免费下载！ http://bbs.520101.com Meridian 1 Supplier to provide CB, EMC, ISO13460-2 RUSSIA GOST R 50377-1992 GOST certificate Philips report and TCO certificate IS 1121, Certificate of ISRAEL Need to provide Israel IEC60950/IEC60950-1 Conformity user manual and Local Certificate of representative ISRAEL...
- Page 80 AUSTRALI sample to Australia AS/NZS3548:1995 and pay transportation AS/NZS CISPR22: 2002 CB, EMC report NEW-ZEAL cost, Supplier to apply Class B for C-Tick through Philips NSO Saudi EN60950-1:2001 SASO Arabia Saudi EN55022, EN61000-3-2, SASO Arabia EN61000-3-3, EN55024 VCCI class B ( CISPR...
- Page 81 Supplier has to check regulation information on rating label, carton label and user manual to meet all mandatory regulation. Supplier need to add Philips sales name, model no into BSMI, TCO, eK, MIC certificate. 10. Supplier has to apply all mandatory regulation bases on sales country.
-
Page 82: Emc Requirements
10.2 EMC Requirements Supplier DVT EMI test result must be submitted prior to DVT samples delivery, and PVT EMI test result must be submitted again prior to PVT samples delivery which also has to meet Philips' immunity testing specification. 10.3 RoHS... - Page 83 4. When the HV circuitry is operating properly there is no possibility of an x- tube must be the same type as the original, including suffix letter, or a Philips radiation problem. High voltage should always be kept at the manufacturer's approved type.