Table of Contents
Advertisement
Vertical air flow adjustment (manually)
To adjust vertical air ow direction, adjust any one of the
horizontal louvre blades. When adjusting the horizontal louver
blades up or down, always keep the top or bottom blades
horizontal
. This can e ectively prevent water droplets condensing
on the front panel of the unit.
Air Filter
The air lter behind the inlet grille should be checked and
cleaned at least once every 2 weeks (or as necessary) to
maintain optimal performance of the air conditioner.
How to remove the air filter
Hold the slot under the front panel, then uplift it outwards,
1.
and remove the front panel.
Pinch the handle under the air lter and make the air lter
2.
arched, remove it from the slot from underside to upside.
3. Clean the lter with warm, soapy water. The water
should be below 40 C to prevent distortion of the lter.
O
4. Rinse o and gently shake o excess water from the
lter. Allow the lter to dry before replacing it. To prevent
distortion of the lter, do not dry in direct sunlight.
Drainage
See the following procedures to perform back drainage:
1. Fit the seal onto the drain joint (provided with your air
conditioner as accessory.)
2. Remove the rubber plug from the back of the unit
(if applicable) and insert it into the bottom drain hole.
3. Attach the drain joint to the back of the cabinet where you
removed the plug and rotate it 90
to securely assemble them.
o
4. Connect the drain joint with an extension drain hose
(locally purchased)
Note: If you choose non-drainage when cooling, both the bottom and the back drain holes of the unit
should be inserted with rubber plugs. When you choose non-drainage, the air conditioner will give
optimal cooling efficiency, but the unit may have a splashing sound due to the blower wheel hitting the
accumulated water gathered in the base pan. The water then hits the condenser, and this results in a
higher cooling efficiency.
DRAIN
JOINT
SEAL
7
HANDLING THE REMOTE CONTROLLER
5m
CAUTIONS
The air conditioner will not operate if curtains, doors or other materials block the signals
from the remote controller to the unit.
Prevent any liquid from falling into the remote controller. Do not expose the remote
controller to direct sunlight or heat.
If the infrared signal receiver on the indoor unit is exposed to direct sunlight, the air
conditioner may not function properly. Use curtains to prevent direct sunlight on the
receiver.
If other electrical appliances react to the remote controller, either move these
appliances or consult your local dealer.
Installation instructions of battery
Step 1: Insert a coin vertically in the groove
on the battery cover, clockwise rotation of 45
degrees, make sure that the groove is aligned
with the "unlock" sign
as shown below
and remove the battery cover.
Lock sign
Coin
Unlock sign
Battery cover
Groove
Step 2: Install battery inside the remote
controller, the positive (+) side up.
RUBBER
PLUG
Battery
Location of the remote controller.
Use the remote controller within a distance of 5
meters from the appliance, pointing it towards
the receiver. Reception is confirmed by a beep.
Step 3: Install the battery cover, make
sure the battery cover groove
with the "unlock" sign. I
vertically in the groove and press it
gently, then counter clockwise rotation
of 45 degrees, make sure the groove is
Lock sign
aligned with the "lock" sign as shown
Coin
below.
Unlock sign
Groove
Battery cover
Battery cover
Coin
Groove
WARNING
1. Battery must be disposed of properly. Do not
Positive (+) side up
short circuit or dispose of in the fire.
2. Keep batteries out of the reach of children.
3. Caution for ingestion.
4. Non-rechargeable batteries are not to be
recharged.
5. Exhausted batteries are to be removed from
the product.
8
is aligned
nsert a coin
Lock sign
Lock sign
Coin
Unlock sign
Unlock sign
Battery cover
Groove
Hide quick links:
Advertisement
Table of Contents
