Summary of Contents for N.KO B15 AIR
- Page 1 MANUAL BEVELLING AND DEBURRING SYSTEM B15 AIR ord. No. 27 220 Operating Instructions for the device Subject to change...
-
Page 2: Table Of Contents
Table of Contents General Information Description of the machine B15 AIR Identification Data Tests Warranties Safety Considerations Technical Specifications Accessories Unpacking of the Device B15 AIR Control Elements Setting of the draft Bevelling Change to the Bevel Angle and Shape Replacing of the Cutter Head... -
Page 3: General Information
This manual contains all instructions for installation, adjustment, operation and maintenance of the machine B15 AIR in compliance with the applicable safety standards. Information contained in this manual may be subject to changes due to further improvement of machines. If on doubt upon finding any differences, please contact N.KO Machines. -
Page 4: Description Of The Machine B15 Air
2. Description of the machine B15 AIR The machine B15 AIR is intended only for the following applications: B15 AIR is intended only for bevelling and deburring of metal materials in a workshop or a production hall. It is a manual, hand-operated machine. The main advantage of the machine is its ability to machine both flat and shaped workpieces, openings as well as pipes. -
Page 5: Safety Considerations
The manufacturer's warranty shall be deemed void in the event of: improper use of the machine, use contrary to national or international standards, incorrect installation, faulty supply of compressed air or its poor quality serious deficiencies in maintenance, ... -
Page 6: Technical Specifications
Personal Injury Protection at work, use safety goggles, solid footwear, ear protectors, suitable head wear, e.g. a hard cap. Connect the machine to the compressed air distribution only if the starting valve of the machine is in the OFF position. ... -
Page 7: Accessories
Unpack the machine from the boxboard and check whether everything is all right and whether the machine is free of any defects. Should you have any questions, contact your distributor. The machine B15 AIR is supplied together with the necessary tools for operation, but without the tool and quick coupling for air supply. -
Page 8: B15 Air Control Elements
10. B15 AIR Control Elements Fig. 10.0.1 A. Starting valve B. Starting valve fuse C. Engine body D. Right and left handle E. Pressure disc with a sleeve F. Guide, stop roller of the cutter G. Scale for reading of bevel angle settings H. -
Page 9: Use
Important: The device can be used only if it is fitted with cutting tips supplied by your distributor or the manufacturer of the equipment. They are four-side cutting tips. The device is fitted with 6 cutting tips. It is strongly advisable that you use only genuine cutting tips. 11.1 Setting of the draft Caution: While adjusting the machine, use working gloves and other personal protective... - Page 10 fig. 11.1.1 For indicative settings of the draft size and the actual machining process, you can use the tables for settings of various bevel angles. Important: The values in the table are calculated from the so-called 0 point. The 0 point is the point, when the cutter touches the material edge for the first time.
-
Page 11: Bevelling
Important: The machine was designed for preparation of weld surfaces. The accuracy of machining is in the range of +/- 1 mm. Satisfactory results can be achieved only under the condition that the edges of the material have been prepared perfectly. Unfortunately, material is often burnt or sheared. -
Page 12: Change To The Bevel Angle And Shape Replacing Of The Cutter Head
11.3 Change to the Bevel Angle and Shape Replacing of the Cutter Head The machine B15 AIR is designed for the use of multiple kinds of cutter heads, see chapter 8. Accessories When replacing the head, proceed as follows: Disconnect the compressed air distribution. -
Page 13: Replacement Of Cutting Tips
Caution: While adjusting the machine, use working gloves and other personal protective equipment. Operations must be performed with the still machine and after the machine has been disconnected from the compressed air distribution. 11.4 Replacement of Cutting Tips Important: Work only with sharp and undamaged cutting tips. Thus you can avoid damages to the machine. -
Page 14: Spare Parts
The machine B15 AIR is equipped with a pneumatic drive. For flawless operation, provide for compressed air with sufficient quality. In order to achieve such quality, there are filtration and lubrication units. The correct selection of the unit shall be consulted with your supplier or directly with the manufacturer of the B15 AIR device, i.e. - Page 19 A copy of this manual is supplied with each machine B15 AIR. All rights reserved. No part of this publication may be reproduced without prior consent granted by N.KO. Manufacturer's and Distributor's Address: N.KO spol. s r.o. a Member of Richtr Group Táborská...