Related Manuals for Quanmax QDSP-2090 Series
Summary of Contents for Quanmax QDSP-2090 Series
- Page 1 QDSP-2090 Series Digital Signage Player with Intel® Haswell Processor User’s Guide...
-
Page 2: Table Of Contents
System tour......................15 Mechanical Dimensions..................18 Chapter 2 Getting Started ....................19 Setting up your PC ....................19 Connecting VESA Mount on QDSP-2090 Series ..........23 Mounting your PC to a monitor................24 Chapter 3 AMI BIOS Setup ....................25 Overview ........................25 ... -
Page 3: Figures
Figure 6 COM port....................21 Figure 7 Network cab le with RJ45 connector ...........22 Figure 8 Turning on the system ................22 Figure 9 VESA Mount Assemb ly.................23 Figure 10 VESA Mount on QDSP-2090 Series ..........23 Figure 11 VESA mounting ..................24 QDSP-2090 Series User’s Manual... -
Page 4: Tables
Tables Tables Table 1 QDSP-2090 Series Specification ............14 Table 2 BIOS Main Menu ..................26 Table 3 Advanced Menu ..................27 Table 4 Advanced Menu – Display Configuration..........28 Table 5 Advanced Menu – Super IO Configuration..........29 Table 6 Advanced Menu –Super IO Configuration – Serial Port 1 Configuration ....................29... -
Page 5: Safety Instructions
Turn off system power, turn off the power supply, and then disconnect the power cord from its source before removing the chassis cover. Turning off the system power switch does not remove power to components. QDSP-2090 Series User’s Manual... -
Page 6: When Working Inside A Computer
ESD procedure to reduce the risk of damage to components. We strongly encourages you to follow proper ESD procedure, which can include wrist straps and smocks, when servicing equipment. You can also take the following steps to prevent damage from electrostatic discharge (ESD): QDSP-2090 Series User’s Manual... -
Page 7: Instructions For Lithium Battery
Do not dispose of lithium batteries in domestic waste. Dispose of the battery according to the local regulations dealing with the disposal of these special materials (e.g. to the collecting points for disposal of batteries) QDSP-2090 Series User’s Manual... -
Page 8: Preface
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment to an outlet on a circuit different from that to which the QDSP-2090 Series User’s Manual... - Page 9 The assembler of a personal computer system may be required to test the system and/or make necessary modifications if a system is found to cause harmful interference or to be noncompliant with the appropriate standards for its intended use. QDSP-2090 Series User’s Manual...
-
Page 10: Maintaining Your Computer
Operating a system at a high altitude (low pressure) can cause electrical problems related to arcing and corona effects. This condition can also cause sealed components with internal pressure, such as electrolytic capacitors, to fail or perform at reduced efficiency. QDSP-2090 Series User’s Manual... - Page 11 Surge protectors should be used with all UPS systems, and the UPS system should be Underwriters Laboratories (UL) safety approved. QDSP-2090 Series User’s Manual...
-
Page 12: Chapter 1 Introduction
Chapter 1 Chapter 1 Introduction Overview QDSP-2090 Series is a compact size Box PC ideal for space critical applications. ® This embedded hardware platform features 4th Generation Intel Core™ i3/i5/i7 ® Processors, Intel H81 / Q87 Express Chipset, and DDR3 SO-DIMM. It comes with a 2.5”... -
Page 13: Product Specifications
2 x mPCIe slot (1x full size, 1x half size, Optional for 3G/WiFi/Bluetooth module, QDSP-2090) 2 x mPCIe/mSATA slot (1x full size, 1x half size, Optional for Expansion 3G/WiFi/Bluetooth module, QDSP-2091) 1x SIM card slot (for 3G appliance) support user accessible QDSP-2090 Series User’s Manual... -
Page 14: Table 1 Qdsp-2090 Series Specification
200 x 153.1 x 35 mm / 7.87" x 6.03" x 1.38" (W x D x H) Dim ensions 1 Kg / 2.20 lb Weight VESA Mount Mounting CE, FCC Class A Certifications Table 1 QDSP-2090 Series Specification QDSP-2090 Series User’s Manual... -
Page 15: System Tour
WiFi LED (Green) When the data is Transferring, the WiFi LED will blink. The USB (Universal Serial Bus) port is compatible with USB devices such as keyboards, mouse devices, cameras, and hard disk drives. USB allows many QDSP-2090 Series User’s Manual... - Page 16 The microphone jack is designed to connect the microphone used for video conferencing, voice narrations, or simple audio recordings. Line-IN The Line-in jack is designed to take input from a higher-powered sound source. 3G External Antenna Spared hole on the casing for connecting 3G external antenna QDSP-2090 Series User’s Manual...
-
Page 17: Figure 2 Rear Io
The supplied power adapter converts AC power to DC for use with this jack. Power supplied through this jack supplies power to the PC. To prevent damage to the PC, always use the supplied power adapter. WiFi External Antenna Spared hole on the casing for connecting WiFi external antenna QDSP-2090 Series User’s Manual... -
Page 18: Mechanical Dimensions
Chapter 1 Mechanical Dimensions Dimension: 200 x 35 x 153.1 mm (W x H x D) Figure 3 Mechanical Dimensions QDSP-2090 Series User’s Manual... -
Page 19: Chapter 2 Getting Started
Setting up your PC ￭ Connect the monitor, mouse and keyboard Connecting the monitor Connect the DVI-I / DP cable from your display to the DVI-I / DP port. DVI-I Figure 4 Connect the DVI-I / DP cable QDSP-2090 Series User’s Manual... -
Page 20: Figure 5 Connecting Usb Mouse & Keyboard
Chapter 2 Connecting USB mouse & keyboard Your QDSP-2090 Series does not come with a keyboard and mouse, but you can use any USB keyboard or mouse with your computer. 2x USB3.0 4x USB3.0 6x USB3.0 Figure 5 Connecting USB mouse & keyboard (Upper: QDSP-2090; Lower: QDSP-2091) NOTE Using a third-party USB mouse or keyboard may require software drivers. -
Page 21: Figure 6 Com Port
Chapter 2 COM port COM port with the pin definitions. Half Duplex Full Duplex RS-232 RS-422 RS-485 RS-485 DATA- DATA+ Figure 6 COM port QDSP-2090 Series User’s Manual... -
Page 22: Figure 7 Network Cable With Rj45 Connector
Connect the other end of the AC power cord to a corresponding outlet. Press the power switch to turn on the system DC Jack Power Button Figure 8 Turning on the system QDSP-2090 Series User’s Manual... -
Page 23: Connecting Vesa Mount On Qdsp-2090 Series
Take out the VESA mounting kit form your package and facing it onto the bottom of QDSP-2090 Series. Figure 9 VESA Mount Assembly Then tightening the screws on your QDSP-2090 Series as figures shown below. Following figures are the complete status when you done. Figure 10 VESA Mount on QDSP-2090 Series QDSP-2090 Series User’s Manual... -
Page 24: Mounting Your Pc To A Monitor
Firstly, mount your VESA kit on the backside of the monitor with four screws in the package. Secondly, place the QDSP-2090 Series on the VESA mounting kit and then tightening the screws from the holes on both sides of the VESA bracket - make sure the computer is fitting well on the bracket. -
Page 25: Chapter 3 Ami Bios Setup
It is possible for the CMOS battery to fail, which will cause data loss in the CMOS only. If this happens you will need to reconfigure your BIOS settings. QDSP-2090 Series User’s Manual... -
Page 26: Main Menu
F3: Optimized Defaults Frequenc y 1600 MHz F4 Save & Exit Sys tem date [Sun 01/11/2015] ESC Exit Sys tem ti me [19:36:12] Access Level Admi nistrator Version 2.17.1249. C opyright (C) 2015, American M egatrends, Inc. QDSP-2090 Series User’s Manual... -
Page 27: Advanced Menu
Version 2.17.1249. C opyright (C) 2015, American M egatrends, Inc. Onboard LAN 1 Controller Options: Disabled, Enabled Onboard LAN 1 Boot Options: Disabled, Enabled Onboard LAN 2 Controller Options: Disabled, Enabled Onboard LAN 2 Boot Options: Disabled, Enabled Audio Controller Options: Disabled, Enabled QDSP-2090 Series User’s Manual... -
Page 28: Table 4 Advanced Menu - Display Configuration
Options: 32M, 64M, 96M, 128M, 160M, 192M, 224M, 256M, 288 M, 320M, 352M, 384M, 416M, 448M, 480M, 512M DVMT Total Gfx Mem Options: 128M, 256M, MAX Primary IGFX Boot Displa y Options: VBIOS Default, CRT, DVI, DP1, DP2 QDSP-2090 Series User’s Manual... -
Page 29: Table 5 Advanced Menu - Super Io Configuration
IO=2F8h; IRQ=3, 4, 5, 6, 7, 9, 10, 11, 12; IO=3E8h; IRQ=3, 4, 5, 6, 7, 9, 10, 11, 12; IO=2E8h; IRQ=3, 4, 5, 6, 7, 9, 10, 11, 12; Serial Port Type Options: RS232, RS422, RS485 QDSP-2090 Series User’s Manual... -
Page 30: Table 7 Advanced Menu -Cpu Chipset Configuration
VT-d Options: Disabled, Enabled Active Processor Cores Options: All, 1, 2, 3 Limit CPUID Maximum Options: Disabled, Enabled Execute Disable Bit Options: Disabled, Enabled Intel® Virtualization Technology Options: Disabled, Enabled Intel® TXT(LT) Support Options: Disabled, Enabled QDSP-2090 Series User’s Manual... -
Page 31: Table 8 Advanced Menu - Sata Configuration
Version 2.17.1249. C opyright (C) 2015, American M egatrends, Inc. SATA Controller(s) Options: Enabled, Disabled SATA Mode Selection Options: IDE, AHCI SATA Controller Speed Options: Default, Gen 1, Gen 2, Gen 3 Port Options: Disabled, Enabled QDSP-2090 Series User’s Manual... -
Page 32: Table 9 Advanced Menu - Usb Configuration
Version 2.17.1249. C opyright (C) 2015, American M egatrends, Inc. Legacy USB Support Options: Enabled, Disabled, Auto XHCI Legacy Support Options: Enabled, Disabled XHCI hand-off Options: Enabled, Disabled EHCI hand-off Options: Disabled, Enabled USB Mass Storage Driver Support Options: Disabled, Enabled QDSP-2090 Series User’s Manual... -
Page 33: Table 10 Advanced Menu - H/W Monitor
+VIN : +12.060 V ESC Exit : +5.066 V +VMEN : +1.541 V Version 2.17.1249. C opyright (C) 2015, American M egatrends, Inc. CPU Warning Temperature Options: Disabled, 80 C, 85 C, 90 C, 95 C QDSP-2090 Series User’s Manual... -
Page 34: Power Menu
Resume By LAN De vice Options: Enabled, Disabled Resume By PCI-E Device Options: Disabled, Enabled Resume By Ring De vice Options: Disabled, Enabled Resume By RTC Alarm Options: Disabled, Enabled Watchdog Timer Configuration WDT Function Options: Disabled, Enabled QDSP-2090 Series User’s Manual... -
Page 35: Security Menu
The pass word l ength must be in the followi ng range: F3: Optimized Defaults Minimum Length F4 Save & Exit Maxi mum length ESC Exit Admi nistrator Pass word User Pass word Version 2.17.1249. C opyright (C) 2015, American M egatrends, Inc. QDSP-2090 Series User’s Manual... -
Page 36: Boot Menu
Version 2.17.1249. C opyright (C) 2015, American M egatrends, Inc. Full Screen LOGO Display Options: Disabled, Enabled Bootup Numlock State Options: On, Off CSM Support Options: Enabled, Disabled Boot Option Filter Options: UEFI and Legacy, Legacy only, UEFI only QDSP-2090 Series User’s Manual... -
Page 37: Save & Exit Menu
+- Change Opt. Save C hanges F1: General H elp Discard Changes F2: Previous Values F3: Optimized Defaults Restore Defaults F4 Save & Exit ESC Exit Version 2.17.1249. C opyright (C) 2015, American M egatrends, Inc. QDSP-2090 Series User’s Manual... - Page 38 Load Optimal Default values for all the setup values. This option allows you to load failsafe default values for each of the parameters on the Setup menus, which will provide the most stable performance settings. The F8 key can be used for this operation. QDSP-2090 Series User’s Manual...
-
Page 39: Chapter 4 Driver Installation
Chapter 4 Chapter 4 Driver Installation If your QDSP-2090 Series does not come with an operating system pre-installed, you will need to install an operating system and the necessary drivers to operate it. After you have finished assembling your system and connected the appropriate power source, power it up using the power supply and install the desired operating system.
Need help?
Do you have a question about the QDSP-2090 Series and is the answer not in the manual?
Questions and answers