Page 1
KD-S871R SERVICE MANUAL CD RECEIVER KD-S871R TP/PTY ¢ DISP MODE COMPACT DIGITAL AUDIO Area Suffix Continental Europe EX---------Central Europe Contents Safety precaution Flow of functional -------------------------- Preventing static electricity operation unit TOC read 1-13 --------------- --------- Important for laser products...
KD-S871R Safety precaution Burrs formed during molding may be left over on some parts of the chassis. Therefore, pay attention to such burrs in the case of preforming repair of this system. Please use enough caution not to see the beam directly or touch it in case of an adjustment or operation check.
Page 3
KD-S871R Preventing static electricity Electrostatic discharge (ESD), which occurs when static electricity stored in the body, fabric, etc. is discharged, can destroy the laser diode in the traverse unit (optical pickup). Take care to prevent this when performing repairs. 1.1. Grounding to prevent damage by static electricity Static electricity in the work area can destroy the optical pickup (laser diode) in devices such as DVD players.
Page 4
KD-S871R Important for laser products 5.CAUTION : If safety switches malfunction, the laser is able 1.CLASS 1 LASER PRODUCT to function. 2.DANGER : Invisible laser radiation when open and inter 6.CAUTION : Use of controls, adjustments or performance of lock failed or defeated. Avoid direct exposure to beam.
KD-S871R Disassembly method <Main body> Removing the front panel assembly (See Fig.1) Press the eject button in the lower right part of the front panel. Remove the front panel assembly from the body. Front panel assembly Eject button Fig.1 Tab a Removing the front chassis assembly (See Fig.2 and 3)
Page 6
KD-S871R Removing the heat sink (See Fig.4) Remove the three screws A on the left side of the body. Heat sink Fig.4 Joints b Removing the bottom cover (See Fig.5 and 6) Bottom cover Prior to performing the following procedure, remove the front panel assembly, the front chassis assembly and the heat sink.
Page 7
KD-S871R Removing the main board (See Fig.7 and 8) Prior to performing the following procedure, remove the front panel assembly, the front chassis assembly, the heat sink and the bottom cover. Remove the screw B, the two screws C and the...
Page 8
KD-S871R Removing the control switch board (See Fig.10 to 12) Prior to performing the following procedure, remove the front panel assembly. Remove the four screws G attaching the rear cover on the back of the front panel assembly. Unjoint the eleven joints c with the front panel and Rear cover the rear cover.
KD-S871R Damper bracket <CD mechanism section> CD mechanism assembly Removing the CD mechanism control board (See Fig.1 and 2) Unsolder the part a and b on the CD mechanism control board. Remove the stator fixing the CD mechanism control board and the damper bracket (To remove the stator smoothly, pick up the center part).
Page 10
KD-S871R Damper bracket assembly CD mechanism Removing the CD mechanism assembly (See Fig.1, 6 to 9) Prior to performing the following procedure, remove the CD mechanism control board and the front bracket (loading motor). Remove the three screws D and the damper bracket.
Page 11
KD-S871R Removing the feed motor assembly FD screw Part i Feed motor assembly (See Fig.10) Prior to performing the following procedure, remove the CD mechanism control board, the front bracket Part j (loading motor) and the CD mechanism assembly. Remove the two screws F and the feed motor assembly.
6. Digital tester MW 522kHz ~ 1620 kHz 7. Tracking offset meter LW 144kHz ~ 279kHz 8. Test Disc JVC :CTS-1000 9. Extension cable for check EXTGS004-26P 1 Dummy load Exclusive dummy load should be used for AM,and FM. For FM dummy load,there is a loss of 6dB between SSG output and antenna input.The loss of 6dB need not be considered...
Page 13
KD-S871R Flow of functional operation until TOC read Power ON • When the laser diode correctly Set Function to CD • When the pickup correctly moves emits to the inner area of the disc Microprocessor Microprocessor Disc inserted commands commands TC9462 "53"...
Page 14
KD-S871R Feed Section Check CD 9V Is the voltage output at Is the wiring for IC521 Is 5V present at IC581 and 5V. IC521 pin "53" 5V or 0V? (90) ~ (100) correct? pin "11"? Check the vicinity of IC521.
Page 15
KD-S871R Maintenance of laser pickup (1) Cleaning the pick up lens Before you replace the pick up, please try to clean the lens with a alcohol soaked cotton swab. (2) Life of the laser diode When the life of the laser diode has expired, the following symptoms will appear.
Description of major ICs UPD178078GF-561 (IC701) : System CPU 1.Pin layout 2.Pin function (1/2) Symbol FUNCTION No use BUSINT JVC bus communication line BUSSI JVC bus communication line BUSSO JVC bus communication line JBUS-SCK JVC bus communication line No use...
Page 17
KD-S871R 2.Pin function (2/2) UPD178078GF-561 Symbol FUNCTION GNDPLL AMEO PLL error output for AM FMEO PLL error output for FM IC(VPP) Setting to write for flash RESET System reset CD mech switch REMOCON Remocon input No use TEL-MUTE No use...
Page 18
KD-S871R LA4743K(IC301):Power amp 1.Block diagram 2200 F 0.022 F Vcc 1/2 Vcc 3/4 IN 1 OUT 1+ 0.22 F OUT 1- PWR GND1 Protective circuit OUT 2+ IN 2 OUT 2- 0.22 F PWR GND2 ST BY Stand by Switch...
Page 19
KD-S871R 2.Terminal layout 3.Pin function LA4743K Pin No. Symbol Function Header of IC Power GND OUTRR- Outpur(-) for front Rch STBY Stand by input Output (+) for front Rch OUTRR+ Power input VCC1/2 OUTRF- Output (-) for rear Rch Power GND...
Page 20
KD-S871R LA6567H-X(IC501):BTL driver 1.Pin layout & blockdiagram CH 3,4,5 Thermal shutdown VCC2 Power supply V05- V05+ S-GND V04+ VCONT V04- VIN4 V03+ VIN4G Signal system power supply V03- VCC-S V02+ VREF-IN 5VREG(PNPTr The outside putting) V02- REG-OUT V01+ REG-IN V01-...
Page 21
KD-S871R 2. Pin function LA6567H-X(2/2) Pin no. Symbol Function VCC2 CH3,4,5 Power supply( It is short with VCC1,VCC-S) V05- Loading output(-) V05+ Loading terminal (+) V04+ CH4 Output terminal(+) V04- CH4 Output terminal(-) V03+ CH3 Output terminal(+) V03- CH3 Output terminal(-)
Page 23
KD-S871R TC9462F(2/3) Symbol Pin No. Function Remarks Non connected HSSW Non connected ZDET Phase difference signal output terminal of EFM 3-state output. signal and PLCK signal. (P2VREF,PVREF,VSS) TMAX detection result output terminal. Selected by 3-state output. TMAXS command bit (TMPS) (P2VREF,PVREF,VSS) TMAX detection result output terminal.
Page 24
KD-S871R TC9462F(3/3) Symbol Pin No. Function Remarks Test input terminal, Normally, keep at "L" level Analog input. TESIN Test input/output terminal. Normally, keep at "L" level Analog input. TESIO1 Digital GND terminal Crystal oscillator connecting input terminal for DSP Crystal oscillator connecting output terminal for DSP...
Page 25
KD-S871R HA13164A (IC961) : Regurator 1.Pin layout 2.Block daiagram Surge Protector 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 BIAS 3.Pin function Pin No. Symbol Function REMOTE Output voltage is VCC-1V.When M or H level applied to CTRL pin.
Page 26
KD-S871R HD74HC126FP-X (IC801) : Buffer 1.Terminal layout 3.Pin function Input Output Note: H : High L : Low X : H and L Z : H.L.X 2.Block diagram Output Input Output Sample as Load Circuit 1 Output Sample as Load Circuit 1...
Page 30
KD-S871R TEA6320T-X (IC161) : E.volume 1.Pin layout 2.Block diagram OUTRR OUTLR VOLUME 2 MUTE 0 to 55 dB OUTRF FUNCTION OUTLF BALANCE ZERO CROSS FENDER REAR POWER DETECTOR SUPPLY VOLUME 1 BASS TREBLE +20 to -31 dB VOLUME 2 LEFT...
Page 31
KD-S871R VICTOR COMPANY OF JAPAN, LIMITED MOBILE ELECTRONICS DIVISION PERSONAL & MOBILE NETWORK BUSINESS UNIT. 10-1,1Chome,Ohwatari-machi,Maebashi-city,371-8543,Japan 200202 (No.49691) Downloaded from www.Manualslib.com manuals search engine...
KD-S871R PARTS LIST [ KD-S871R ] * All printed circuit boards and its assemblies are not available as service parts. Area suffix E ----------- Continental Europe EX --------------- Central Europe - Contents - 3- 2 Exploded view of general assembly and parts list (Block No.M1) 3- 4 CD mechanism assembly and parts list (Block No.MB)
KD-S871R Exploded view of general assembly and parts list Block No. Downloaded from www.Manualslib.com manuals search engine...
Page 40
KD-S871R Parts list (General assembly) Block No. M1MM Item Description Parts number Parts name Q'ty Area --------------- CD MECHA 1 TN-CCD1001Z-136J FSJC1029-404 TOP CHASSIS FSMH3001-202 SIDE PANEL FSKM3011-002 BOTTOM COVER FSMA3004-203 INSULATOR QYSDST2604Z SCREW 3 CHASSIS+MECHA BKT SCREW 2 CHASSIS+SIDE PANEL...
KD-S871R CD mechanism assembly and parts list Block No. Grease TN-CCD1001Z-136J G-31SA G-31SA(Bottom side) RX-405 106 29 Downloaded from www.Manualslib.com manuals search engine...
Page 42
KD-S871R Parts list (CD mechanism) Block No. MBMM Item Description Parts number Parts name Q'ty Area 30310101T FRAME 30310103T DANPER PIN 30310107T UPPER PLATE 30310108T SEL STOP PLATE 30310142T SEL ARM (L)L 30310143T SEL ARM (R)L S ARM SPRING(L) 30310145T...
Page 43
KD-S871R Parts list (CD mechanism) Block No. MBMM Item Description Parts number Parts name Q'ty Area 64180403T DET SWITCH 2 ESE22MH3 68150232T CONNECTOR 1 TKC-W26X-C1 30311105T SOPPORT PLATE 30311138T GR MT BLK(N) 30311109T LDG GEAR (2) 30311110T LDG GEAR (3)
Page 44
KD-S871R Electrical parts list (Main board) Block No. 01 Item Parts number Parts name Remarks Area Item Parts number Parts name Remarks Area NDC31HJ-5R0X C CAPACITOR C 331 QERF1HM-225Z E CAPACITOR 2.2MF 20% 50V NDC31HJ-100X C CAPACITOR C 332 NCS31HJ-391X...
Page 45
KD-S871R Electrical parts list (Main board) Block No. 01 Item Parts number Parts name Remarks Area Item Parts number Parts name Remarks Area C 591 NCS31HJ-821X C CAPACITOR D 784 UDZ11B-X ZENER DIODE C 592 QEKJ1EM-475Z E CAPACITOR 4.7MF 20% 25V...
Page 46
KD-S871R Electrical parts list (Main board) Block No. 01 Item Parts number Parts name Remarks Area Item Parts number Parts name Remarks Area R 10 NRS181J-8R2X MG RESISTOR R 503 NRSA63J-242X MG RESISTOR R 31 NRSA63J-102X MG RESISTOR R 504...
Page 47
KD-S871R Electrical parts list (Main board) Block No. 01 Item Parts number Parts name Remarks Area R 715 NRSA63J-103X MG RESISTOR R 716 NRSA63J-103X MG RESISTOR R 717 NRSA63J-103X MG RESISTOR R 718 NRSA63J-103X MG RESISTOR R 719 NRSA63J-472X MG RESISTOR...
Page 48
KD-S871R Electrical parts list (Front board) Block No. 02 Item Parts number Parts name Remarks Area Item Parts number Parts name Remarks Area C 651 NCB31HK-223X C CAPACITOR R 633 NRSA02J-222X MG RESISTOR C 652 NCS31HJ-681X C CAPACITOR R 634...
KD-S871R Packing materials and accessories parts list Block No. Block No. E version A2~A6 EX version A1,A3,A5,A6 E version A1 P5 A15 KIT:A8~A12 3-12 Downloaded from www.Manualslib.com manuals search engine...
KD-S871R Parts list (Packing) Block No. M3MM Item Description Parts number Parts name Q'ty Area FSPG4002-001 POLY BAG 1 INST.BOOK FSPG4002-001 POLY BAG 2 INST.BOOK QPA00801205 POLY BAG 1 KIT QPA01003003 POLY BAG 1 HARD CASE FSYH4036-068 SHEET QPA01003003 POLY BAG...