1. Manuals
  2. Brands
  3. haupa Manuals
  4. Power Tool
  5. AS-6
  6. Instruction manual

haupa AS-6 Instruction Manual

Battery powered hydraulic puncher
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
INSTRUCTION MANUAL
BATTERY POWERED HYDRAULIC PUNCHER
„AS-6"
Art. 21 67 00
Q
DIN EN ISO 9001
ZERTIFIKAT
...convincing solutions

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the AS-6 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for haupa AS-6

Summary of Contents for haupa AS-6

  • Page 1 INSTRUCTION MANUAL BATTERY POWERED HYDRAULIC PUNCHER „AS-6“ Art. 21 67 00 DIN EN ISO 9001 ZERTIFIKAT ...convincing solutions...

  • Page 2: Caracteristicas Tecnicas

    1. CARACTERISTICAS TECNICAS Maximum cutting capacity: Ø 118 mm, 2.5 mm thick steel plate 92 x 92 mm, 2 mm thick steel plate Endurance: 180 holes in Ø 22.5 mm (PG16) Punch time: 6 sec Max yield strength: 45 Kg/mm Cutting force: 60 KN Operating pressure:...

  • Page 3: Operation

    3.2.5. Making square or rectangular holes • To make these holes, proceed as for the previous point (point 3.2.4). …convincing solutions Germany: HAUPA, Königstr. 165-169, 42853 Remscheid Phone: +49 (0)2191 8418-0, Fax: +49 (0)2191 8418-840, sales@haupa.com • Errors and technical changes reserved.

  • Page 4: Battery Removal And Installation

    4. BATTERY REMOVAL AND INSTALLATION 4.1. Battery removal. Hold the grip firmly and press the battery release button to remove it, as shown in the following figures. CAUTION Never short circuit the battery 1. Battery installation Insert the battery ensuring that the poles are correct (see previous figures) 4.2.
  • Page 5 4.3.5. Hold the charger firmly and pull out the battery. NOTE: After use, ensure that the battery is removed from the charger and stored. …convincing solutions Germany: HAUPA, Königstr. 165-169, 42853 Remscheid Phone: +49 (0)2191 8418-0, Fax: +49 (0)2191 8418-840, sales@haupa.com • Errors and technical changes reserved.
  • Page 6 4.4. Electric discharge when using new batteries etc. As the internal chemical contained in new batteries or those that haven’t been used for a long period of time is not active, the electric discharge may be lower when used for the first and second time. This phenomenon is temporary, and the normal time required for recharging will be re-established by recharging the batteries 2 or 3 times.
  • Page 7 Pay attention to the spring orientation. The largest diameter must be on the opposite side to you. …convincing solutions Germany: HAUPA, Königstr. 165-169, 42853 Remscheid Phone: +49 (0)2191 8418-0, Fax: +49 (0)2191 8418-840, sales@haupa.com • Errors and technical changes reserved.
  • Page 8 4.7.4. Use of the torch. a. Press the switch to switch-off the light. If you forget to do so, it will be automatically switched off after 15 minutes. b. The direction of the light can be regulated within the range of support positions 1 to 5. Battery duration: •...

  • Page 9: Care And Maintenance

    Then push the brush with your finger, as shown in the following diagram. Finally, install the carbon brush cover. …convincing solutions Germany: HAUPA, Königstr. 165-169, 42853 Remscheid Phone: +49 (0)2191 8418-0, Fax: +49 (0)2191 8418-840, sales@haupa.com • Errors and technical changes reserved.

  • Page 10: Oil Level

    CAUTION Ensure that the carbon brush toe is inserted in the external tube of the brush contact part. (You can insert either of the two toes supplied). Take care, because a mistake in this operation could deform the toe and prematurely damage the motor.

  • Page 11: Fault Diagnostics

    Always use original spares. Any other part type could seriously damage the tool and would void the guarantee. …convincing solutions Germany: HAUPA, Königstr. 165-169, 42853 Remscheid Phone: +49 (0)2191 8418-0, Fax: +49 (0)2191 8418-840, sales@haupa.com • Errors and technical changes reserved.
  • Page 12 WHEN ORDERING SPARES, ALWAYS PROVIDE THE FOLLOWING INFORMATION: 1. Item code number. 2. Item description. 3. Instruction manual reference and/or date. 4. Tool type. 5. Tool serial number.

  • Page 13: Exploded View Drawing

    EXPLODED VIEW DRAWING Art. 21 67 00 …convincing solutions Germany: HAUPA, Königstr. 165-169, 42853 Remscheid Phone: +49 (0)2191 8418-0, Fax: +49 (0)2191 8418-840, sales@haupa.com • Errors and technical changes reserved.

Table of Contents