Carrier ZS Plus Installation Manual
  1. Manuals
  2. Brands
  3. Carrier Manuals
  4. Temperature Controller
  5. ZS Plus
  6. Installation manual

Carrier ZS Plus Installation Manual

Thermistor-based temperature sensors that may optionally sense humidity, co2, or voc
Hide thumbs Also See for ZS Plus:

Advertisement

Table of Contents

Z
S
S
e
n
s
o
r
s
Z
S
S
e
n
s
o
r
s
I
n
s
t
a
l
l
a
t
i
o
n
G
u
i
d
e
I
n
s
t
a
l
l
a
t
i
o
n
G
u
i
d
e
CARRIER CORPORATION ©2013
A member of the United Technologies Corporation family · Stock symbol UTX · Catalog No. 11-808-503-01 · 11/12/2013

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the ZS Plus and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Carrier ZS Plus

Summary of Contents for Carrier ZS Plus

  • Page 1 CARRIER CORPORATION ©2013 A member of the United Technologies Corporation family · Stock symbol UTX · Catalog No. 11-808-503-01 · 11/12/2013...

  • Page 3: Table Of Contents

    To format a ZS Sensor ............................12 CARRIER CORPORATION ©2013. All rights reserved throughout the world. I-Vu is a registered trademark of Carrier Corporation. BACnet is a registered trademark of ASHRAE. All other trademarks are the property of their respective owners.

  • Page 5: What Are Zs Sensors

    • Green LED to indicate occupied state • Local access port ZS Sensors Carrier Proprietary and Confidential CARRIER CORPORATION ©2013 Rev. 11/14/2013 All rights reserved...

  • Page 6: Rnet Configuration

    Although an Rnet can have 15 ZS Sensors, you can have no more than 5 sensors per control program. • You cannot have SPT sensors and ZS sensors on the same Rnet. ZS Sensors Carrier Proprietary and Confidential CARRIER CORPORATION ©2013 Rev. 11/14/2013 All rights reserved...

  • Page 7: Specifications

    Range: 0 to 2000 ppm Accuracy: 1 PPM Power requirements Temperature only ZS Standard or ZS Plus: 12 Vdc @ 6 mA ZS Pro or Pro-F: 12 Vdc @ 7 mA Temperature with humidity ZS Standard or ZS Plus: 12 Vdc @ 7 mA...
  • Page 8 What are ZS Sensors? Listed by FCC Part 15-Subpart B-Class A, CE ZS Sensors Carrier Proprietary and Confidential CARRIER CORPORATION ©2013 Rev. 11/14/2013 All rights reserved...

  • Page 9: To Address A Zs Sensor

    Switch value EXAMPLE DIP switches 1 and 4 above are on. Their values (1 + 8) total 9, so the sensor's address is 9. ZS Sensors Carrier Proprietary and Confidential CARRIER CORPORATION ©2013 Rev. 11/14/2013 All rights reserved...

  • Page 10: Wiring And Mounting A Zs Sensor

    The Rnet communicates at a rate of 115 kbps and should be wired in a daisy-chain, star, or hybrid configuration. Power requirements Power requirements Temperature only ZS Standard or ZS Plus: 12 Vdc @ 6 mA ZS Pro or Pro-F: 12 Vdc @ 7 mA...

  • Page 11: Rnet Wiring Specifications

    500 feet (152 meters) Insulation Low-smoke PVC (or equivalent) Color Code Black, white, green, red Shielding If shielded, Aluminum/Mylar shield (100% coverage) with TC drain wire, terminated at controller ZS Sensors Carrier Proprietary and Confidential CARRIER CORPORATION ©2013 Rev. 11/14/2013 All rights reserved...

  • Page 12: To Wire And Mount A Zs Sensor

    If wiring 2 cables in a daisy-chain configuration, twist together the shield wires, then wrap the shield wires with tape. ZS Sensors Carrier Proprietary and Confidential CARRIER CORPORATION ©2013 Rev. 11/14/2013 All rights reserved...
  • Page 13 Wiring and mounting a ZS Sensor Insert the other 4 wires into the ZS Sensor's screw terminal connector. If wiring 2 cables, insert like-colored wires into each terminal. Carrier recommends that you use the following Rnet wiring scheme: Connect this To this wire...

  • Page 14: To Communicate Through The Local Access Port

    USB Link Kit NOTE If using a USB isolator, plug the isolator into your computer's USB port, and then plug the USB Link cable into the isolator. ZS Sensors Carrier Proprietary and Confidential CARRIER CORPORATION ©2013 Rev. 11/14/2013 All rights reserved...

  • Page 15: Troubleshooting

    • Wiring connections • Controller operating status Characters that The sensor may have a memory problem. Try formatting the sensor seem out (page 12). of place ZS Sensors Carrier Proprietary and Confidential CARRIER CORPORATION ©2013 Rev. 11/14/2013 All rights reserved...

  • Page 16: To Format A Zs Sensor

    Set the DIP switches back to their original position. Reattach the wiring connector. NOTE If you move a sensor from one controller to another controller that has a different control program, format the sensor. ZS Sensors Carrier Proprietary and Confidential CARRIER CORPORATION ©2013 Rev. 11/14/2013 All rights reserved...
  • Page 18 CARRIER CORPORATION ©2013 A member of the United Technologies Corporation family · Stock symbol UTX · Catalog No. 11-808-503-01 · 11/12/2013...

This manual is also suitable for:

Zs pro-fZs standardZs pro

Table of Contents