Related Manuals for Viking VS 2625
Summary of Contents for Viking VS 2625
- Page 1 VS 2625 2-WAY LCD PAGER ALARM Operation Manual MEGATRONIX CHATSWORTH, CA USA VS 2625 OPERATE...
-
Page 2: Table Of Contents
7. Enable / Disable Bi Sound While Pressing Button: 8. Low Battery Indication 9. Set Up Fixed Count Down Timer 10. Out Of The Range Check D. TIMER SETTING ……………………………….………………………..…………………….…………..……. 12 1. Timer Setting 2. Alert Alarm Timer Setting 3. Count Down Timer Setting VS 2625 OPERATE... -
Page 3: Remote Transmitter Operation
2 or 3 Flashes Fast Flash or Unlocking Turns on for 30 -second 3. Trigger Alarming Flashes Slow Flash Disable Flashes 4. Panic Alarming Flashes Flashes 5. Car-Jacking Alarming Flashes Disable Flashes 6. Car Locator 6 Chirps 12 Flashes VS 2625 OPERATE... -
Page 4: Active Arming - Arm & Lock
2. The siren will chirp twice and parking light will flash twice and then remain on for 30 seconds indicating that the security system is now disarmed. The vehicle doors will unlock and dome light wills turns on for 30 seconds upon disarming when interfaced with the security system. VS 2625 OPERATE... -
Page 5: Tamper Disarming
4. Within 15 seconds, press and release the valet switch 3 times 5. Turn the Ignition Switch to “Off” position. [4] Chirps form siren/horn, [3] flash from parking light and LED will turn off to indicate the system was disarmed. VS 2625 OPERATE... -
Page 6: Valet Mode
Then it will stop and automatic reset and re-arm. If the one of sensors or detectors is still active, the alarm system will sound a maximum of 6 times of 30 seconds cycles. VS 2625 OPERATE... -
Page 7: Anti Car-Jacking
90 seconds after the system has been triggered: 1. The siren will continue alarming and the parking lights flashing, and 2. The starter disable will activate to prevent the vehicle from starting. 3. It will remain active until the vehicle's battery power is exhausted. VS 2625 OPERATE... -
Page 8: Override The System To Turn Off Anti Car Jacking
1. Turn the ignition switch on and close all the vehicle’s doors. After 3 seconds, the system will automatically lock the central locking system. 2. Turn the ignition switch off. The system will automatically unlock the central locking system. VS 2625 OPERATE... -
Page 9: Trunk Release (Channel 3) Output
In – Range Indicator You are transmitting the signal to You are within the remote control range. control unit Door Open Warning Trunk/Hood Trigger Doors are illegally opened (Zone 3) Trunk or Hood is illegally opened (Zone 2) VS 2625 OPERATE... -
Page 10: Programming Of The Lcd Remote Transceiver
3 seconds press and hold the button for 2 seconds to activate or cancel the button lock function. The icon will be displayed on the LCD screen to show the LCD remote transmitter is on “Button Lock”. VS 2625 OPERATE... -
Page 11: Vibration / Melody Mode
“Hour” digit until AM10:xx 3. Press the button once again then the “Minute” digit flashes for adjusting. 4. Press the button to decrease or increase the “Minutes” digit until AM 10:30 VS 2625 OPERATE... -
Page 12: Timer Setting
This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions. (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. VS 2625 OPERATE...
Need help?
Do you have a question about the VS 2625 and is the answer not in the manual?
Questions and answers