Table of Contents
Advertisement
Quick Links
Designed, Manufactured and Supported in the USA
VIKING
C O M M U N I C A T I O N & S E C U R I T Y S O L U T I O N S
Voice Alarm Dialing from Two Inputs
Viking's K-202-DVA is a fully programmable two-
input, multi-number auto dialer, designed for
emergency
and
notification. The K-202-DVA has two dry contact
inputs, each of which can dial up to seven 32-digit
phone numbers and play a message up to 1
minute in length specific to that input.
Messages can be recorded locally or remotely with
a total message time for both inputs of two
minutes. The K-202-DVA has call progress
detection capability with normal and fast busy, call
pickup, CPC and ring-no-answer detection.
Programming is easily done with a Touch Tone
phone.
Features
• Non-volatile memory (no batteries required)
• Stores up to seven 32-digit phone numbers per
input (fourteen 32-digit numbers total)
• 2 minutes of record time (1 minute per input)
• Programmable message repeat counter
• Programmable lap counter
• Two inputs programmable for normally open or
normally closed and enabled or disabled
• Programmable ring delay for remote
programming and alarm polling
• Programmable qualifier timer for each input
(time for an event to be qualified as an alarm)
• Programmable resume timer for each input
(time following reset for input to become active
again)
• Call progress detection
• Programmable ringback limit for call progress
• Remote security and access codes
• Local or remote programming and recording
• Compatible with the RC-2A and RC-3 remote
DTMF controllers
• Phone numbers may be programmed as pager
numbers (no voice message played)
• Programmable hookswitch flash before dialing
• Local reset input
• Local alarm state indication LED
PRODUCT MANUAL
non-emergency
message
Applications
• Security/burglar/fire alarm notification
• System alarm or equipment malfunction
notification
• Environmental warning notification
• Contacting personnel via numeric pagers
www.vikingelectronics.com
Information: (715) 386-8861
Specifications
Power: 120V AC/12V DC 500 mA, UL listed adapter
provided
Dimensions: 133mm x 91mm x 44mm (5.25" x 3.6" x
1.75")
Shipping Weight: 0.68 Kg (1.5 lbs)
Environmental: 0°C to 32°C (32°F to 90°F) with 5% to
95% non-condensing humidity
Talk Battery: 12V DC
Touch Tone Dialing: 100 ms on/off, 50 ms on/off
CPC Detection Time: 320 ms minimum
Message Record Time: 2 minutes
Sampling Rate: 64 K (equivalent)
Input Detection Time: 90 ms with Qualifier Timer set to 0
Resolution Qualifier Timer: 1 second to 18 hours
Resolution Resume Timer: 1 second to 18 hours
Connections: (1) RJ11 jack for telco connection, (1) 6
position screw terminal block for inputs
K-202-DVA
Two-Input Voice
Alarm Dialer
August 24, 2015
Advertisement
Table of Contents
Related Manuals for Viking K-202-DVA
Summary of Contents for Viking K-202-DVA
- Page 1 C O M M U N I C A T I O N & S E C U R I T Y S O L U T I O N S Voice Alarm Dialing from Two Inputs Viking’s K-202-DVA is a fully programmable two- input, multi-number auto dialer, designed for...
- Page 2 Forced Play Timer: The forced play timer is operational when the Call Progress Detection has been disabled. Instead of starting the alarm message when the call is picked up, the K-202-DVA waits a set period of time (from 1 - 99 seconds) after the number is dialed before it starts playing the message.
- Page 3 Make sure the PROG/NORM switch is set to the NORM position and that there is a CO line or analog Step 1. PABX/KSU extension in the TELCO jack. Call into the K-202-DVA on that line or extension. The unit will answer after the set ring delay (see Step 2. Programming section L) and a single beep should be heard.
- Page 4 B. Quick Programming Features (see sections D - U for detailed descriptions) Description Enter Digits + Location To enter phone numbers for each input .................. 1-32 digits + #XY* To clear a phone number ......................(no digits) + #XY* To enter pager numbers ......................1-32 digits + #QXY* Contacts: First digit - 0 = NO, 1 = NC , 2 = enabled, 3 = disabled 2 digits...
- Page 5 To start a recording: enter Q followed by the number of the input. The K-202-DVA gives a single beep to indicate that it is recording and then starts the recording process.
- Page 6 When an input has entered the alarm state, the K-202-DVA dials the first phone number associated with that input. When dialing is completed, the K-202-DVA looks to see if call progress detection is enabled. If it is, the K- 202-DVA counts ringbacks while looking for the called number to answer. If the call is not answered before the programmed ringback limit is reached, the K-202-DVA will hang up and dial the next number in the list.
- Page 7 202-DVA gives 2 beeps, and the for options in Figure 1 on page 6 become available. When finished, dial 3 to disconnect (3 beeps are heard) or just hang up. Note that the K-202-DVA will give 3 beeps and hang up if 20 seconds go by without a touch tone entry.
-
Page 8: Two Year Limited Warranty
This number is valid for fourteen (14) calendar days from the date of issue. 3. After obtaining the R.A. number, return the approved equipment to your distributor, referencing the R.A. number. Your distributor will then replace the Viking product using the same R.A. number.
Need help?
Do you have a question about the K-202-DVA and is the answer not in the manual?
Questions and answers