Ideal Security sk601 Manual page 2

CHIME OR HOME FUNCTION
1. Slide the switch to "CHIME" or Press "HOME" button on the remote control.
You will hear Ding..Dong sound and the "MODE" indication LED will light up
to confirm that the unit is in Chime mode.
2. Wait for 60 seconds after a beep for the sensor to Arm.
When the built-in motion sensor detects movement the unit will sound "Ding
Dong" and the "MODE" indicator LED will flash at the same time.
When a linked wireless sensor triggers the unit, it will sound "Ding Dong" and
the corresponding wireless zone indicator LED will flash at the same time.
3. Slide the switch to "OFF" or press the "DISARM" button on the remote control
to turn the chime function off .
NOTE: The function switch must be set to either "ALARM" or "CHIME" for the
remote control to activate Alarm, Chime (Home), Disarm or Panic
PANIC BUTTON
1. With the function switch on the main unit set to either "ALARM" or "CHIME",
press and hold the "PANIC" button on the remote control for 2 seconds. The
105 dB alarm will be instantly activated and "ZONE 4" indicator LED will flash.
The alarm will sound twice for 30 seconds with 30 seconds silence in between.
2. To stop the alarm slide the function switch on the main unit to "OFF" or press
the "DISARM" button on the remote control.
LINKING ADDITIONAL WIRELESS DEVICES
1. Turn the unit to Chime mode by sliding the switch on the right side to "CHIME".
2. Turn off the integrated motion sensor by sliding the "PIR" switch in the
battery compartment to the OFF position.
Please remember to slide it to the ON position once the linking process is done.
3. Press and hold the "LEARN" button located on the back of the unit for 2
seconds until you hear a long beep tone, release the button.
Set to
ALARM
OFF
CHIME
CHIME
(Fig.7)
4. The zone 1 LED will flash, a short press of the LEARN button will change to
zone 2, a short press again and the zone 3 LED will flash, and so on.
If a zone LED is steady on, that means the zone is full. Zones 1, 2 &3 can
accept 1 wireless device each. Zone 4 can accept up to 5 wireless devices.
5. Once the zone # is chosen, trigger the wireless device that you want to link to
the system (Please refer to its instructions for how to trigger the sensor). If
you hear two long beeps, then the linking process is successful. Otherwise,
please re-learn again. The system will go back to standby mode for each code
learning process. Repeat step 2 to 4 to learn other devices.
7. Slide the integrated motion detector PIR switch back to ON position.
TO REMOVE WIRELESS DEVICES
1. Switch the unit to "CHIME" mode.
2. Press the LEARN button for 2 seconds. You will hear a long beep then release
the button. To select the zone that you want to clear press the button briefly to
cycle through the zones. The zone LED will flash. Press and hold the button for
12 seconds until you hear 2 long beeps then release the button. Now the link
code is cleared from the zone you selected.
3. Repeat if necessary for other zones.
ADDING WIRED CONTACT SENSORS
When mounted permanently the unit is compatible with IDEAL wired magnetic
contact sensors SK619. When connected the sensors will activate the alarm in the
same manner as the built in motion sensor.
1. Mount the contact sensors as described in the instructions for the SK619.
Measure and cut the sensor wires to the length needed to reach the unit plus
about 3 inches of extra wire. Strip about 1/2 inch of insulation from each wire.
2. Open the rear cover of the unit to access the input terminals.
3. Feed the two wires through one of the slots on the side of the unit. Using a
small screwdriver connect one wire to the terminal marked "TRIGGER" and the
other wire to the terminal just beside it marked "GRND". Either wire can be
mounted to either terminal. (Fig.8)
CONTACT SENSOR
4. Close the back cover. The unit is now ready to be armed
LEARN button ADDING A WIRED EXTERNAL SIREN
When mounted permanently the unit is compatible with IDEAL wired exterior
siren SK613. When connected the external alarm will sound when the main unit is
Set PIR to OFF
triggered and the function switch is set to "ALARM". The Siren will not sound when
temporarily
the function switch is set to "CHIME" or "HOME" is selected with the
Remote Control
1. Mount the Siren as described in the instructions for the SK613. Measure and
cut the sensor wires to the length needed to reach the unit plus about 3 inches
of extra wire. Strip about 1/2 inch of insulation from each wire.
2. Open the rear cover of the unit to access the input terminals.
3. Feed the two wires through one of the slots on the side of the unit. Using a
small screwdriver connect the black striped wire (-) to the terminal marked
"GRND" and the other wire (+) to the terminal just beside it marked "SIREN".
The polarity of the wires must be respected for the Siren to function. (Fig.9)
4. Close the back cover. The unit is now ready to be armed
TRIG GND GND SIREN
(Fig. 8)
TRIG GND GND SIREN
-
+
-
+
Black striped wire to GND(-)
-
+
PIR ON OFF
IMPORTANT NOTES:
1. Do not install alarm where it will be exposed to direct sunlight or rain.
2. The alarm siren is very loud, never put the unit close to your ear.
3. Keep away from heat sources such as radiators, heat ducts or stoves.
4. If the unit goes off at random, it is possibly located too close to a heat source.
Changing the location or direction of the unit can remedy this.
5. The unit is designed to be used with the built in AC adapter plugged into a
110V outlet. Batteries will provide short term back-up functionality.
6. It is recommended that batteries be replaced annually - like smoke detector
batteries.
7. For the most up to date installation instructions and trouble shooting
information consult our web site: www.idealinc.com
8. The system can provide valuable protection for your home and property if
utilized properly. However, this unit cannot guarantee complete protection
against burglary or robbery. Therefore, we can not be responsible for any
losses or damages which may occur.
WARRANTY:
This unit is warranted to be free of defective materials and workmanship for a
period of one year from date of purchase. In case of malfunction, this unit will be
repaired or replaced at no charge by Ideal Security Inc. Return the product
postage paid, along with your sales slip to Ideal Security Inc., 7111 Cordner
Street, Lasalle, Quebec, Canada, H8N 2J7. Warranty begins on date of consumer
purchase. Repair or replacement as described above shall be the sole remedy to
the consumer and there shall be no liability on the part of Ideal Security Inc. for
any special, indirect, incidental or consequential damages, including but not
limited to any loss of business or profits whether or not foreseeable.
CUSTOMER SERVICE:
Thank you for your purchase:
We are dedicated to customer service and will work to resolve any difficulties to
ensure customer satisfaction.
If you have any questions about the setup or function of this product, please call
us before returning this product to the point of purchase.
Tel: 800-361-2236 x 230 • Fax: 800-361-3423
e-mail: ideal@idealinc.com
www.idealinc.com • www.idealalert.ca
(Fig. 9)